LG 82-1827-18 86 Inch Class 4K HDR Smart LED Instruction Manual

: July 31, 2024
: LG

Table of Contents

82-1827-18 86 Inch Class 4K HDR Smart LED
Product Specifications
Product Usage Instructions
Before You Begin
For Your Safety
Tools You Will Need
Installation Instructions
Q: Do I need any special tools for installing this

82-1827-18 86 Inch Class 4K HDR Smart LED

“`html

Product Specifications

Model: LG 82-1827-18
Parts Included:
- Trim Frame – 1
- Bottom Duct – 1
- Side Duct – 1
- Phillips screwdriver
- Pencil
- Drill with 7/64 bit or #35
- Awl or punch
- Tape measure
- Screws – 6 (4 required, 2 extra)
- 1/2 Screws – 15 (11 required, 4 extra)
- Anti-Tip Bracket – 1
- Bottom Bracket – 1
- Upper Duct – 1
- Template – 1

Product Usage Instructions

Before You Begin

Read these instructions completely and carefully. Share the
instructions with the consumer. Keep the instructions for future
reference.

For Your Safety

Before installation, switch power off at the service panel and
lock the service disconnecting means to prevent accidental power
switch on. If the service disconnecting means cannot be locked,
attach a prominent warning device to the service panel.

Tools You Will Need

Phillips screwdriver
Pencil
Drill with 7/64 bit or #35
Awl or punch
Tape measure

Installation Instructions

Install the Anti-Tip Bracket

A. Cut the front edge of the template and place it along the
cutout floor to mark the anti-tip bracket location.

Install Side Duct and Upper Duct

A. Connect the side duct to the upper duct by inserting tabs and
bending them up carefully. Clean the microwave oven surface before
attaching the ducts.

B. Drill holes for the anti-tip bracket and attach it using
screws.

C. Position the side duct and upper duct assembly on the
microwave cabinet, aligning with the bottom screw hole, and fasten
it to the cabinet.

Install Microwave Oven into Cabinet

A. Slide the microwave oven partway into the cabinet opening and
plug it in.

B. Ensure the bottom bracket is flat to the cutout floor, slide
the microwave back, making sure the power cord is not mashed or
cut.

C. Center the microwave oven within the cutout opening and slide
it in place, engaging the anti-tip bracket.

Frequently Asked Questions (FAQ)

Q: Do I need any special tools for installing this

product?

A: The installation requires common tools like a Phillips
screwdriver, drill with a specific bit size, awl or punch, and a
tape measure.

“`

This Owner’s Manual is provided and hosted by Appliance Factory Parts.
LG 82-1827-18 Owner’s Manual
Shop genuine replacement parts for LG 82-1827-18
Find Your LG Microwave Parts – Select From 955 Models ——– Manual continues below ——–

Installation Instructions

Built-In Trim Kits
82-1827 and 82-1830

Questions? In the U.S., call 1-800-944-9044. In Canada, call 1-866-213-9397 (English), 1-800-669-4606 ext. 8199 (French). Visit our Website at: www.frigidaire.com

BEFORE YOU BEGIN
Read these instructions completely and carefully.
· IMPORTANT Save these instructions for local inspector’s use.
· IMPORTANT Observe all governing codes and ordinances.
· Note to Installer Be sure to leave these
instructions with the Consumer.
· Note to Consumer Keep these
instructions for future reference.

· Unplug the microwave oven before attempting installation of this kit.
· Skill level Installation of this appliance requires basic mechanical and electrical skills.
· Completion time 1-3 hours
· Proper installation is the responsibility of the installer.
· Product failure due to improper installation is not covered under the Warranty.
· This kit is UL and CUL listed for installation alone or over any Frigidaire single electric wall oven.

FOR YOUR SAFETY:
WARNING Before beginning the
installation, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
TOOLS YOU WILL NEED

PARTS INCLUDED

PART

Trim Frame

QUANTITY 1

Bottom Duct

1

Side Duct

1

Phillips screwdriver Pencil

Drill with 7/64 bit or #35

Awl or punch

Tape measure

READ CAREFULLY.
KEEP THESE INSTRUCTIONS.

164D3370P160 49-40169-1

P/N 316137209 Rev. A

3828W5U 0149

1

Printed in Korea ( 05-01 JR)

1″ Screws

6

(4 required, 2 extra)

1/2″ Screws

15

(11 required, 4 extra)

Anti-Tip Bracket

1

Bottom Bracket

1

Upper Duct

1

Template

1

Installation Instructions

3
.

INSTALL THE ANTI-TIP BRACKET

A Fold or cut the front edge of the template, along the front guide line. Place the template flush along the front edge of the cutout floor, aligning the center line of the template with the center line of the cutout floor. Mark the center positions with an awl or center punch for the anti-tip bracket location as shown.

4
.

INSTALL SIDE DUCT AND

UPPER DUCT

A Connect the side duct to the upper duct as shown.

1. Insert projecting tabs of the upper duct into the holes of the side duct.

2. Bend the tabs up with caution as shown.

NOTE: Remove any oil or dirt on the surface of the microwave oven before the ducts are attached.

Upper Duct

Cutout Floor B Remove the template and drill two holes for the
anti-tip bracket. 1/2 Screws (2)
Anti-Tip Bracket
C Install the anti-tip bracket onto the cutout floor using two 1/2 screws.

3 Holes

3 Tabs

(1)

(2)

Side Duct

B Set the microwave upright, being careful not to bend the front flange. Remove the one existing screw from the left side of the microwave oven.
C Peel off the backing of the double sided tape. Carefully position the side duct and upper duct assembly on the microwave cabinet, aligning with the bottom screw hole. Press down firmly on the ducts. Fasten the duct assembly to the left side of the cabinet with the screw removed above.

Existing Screw (1)

3

Installation Instructions

5
.

INSTALL MICROWAVE OVEN

INTO CABINET

A Slide the microwave oven part way into the cabinet opening.

Bottom Duct

Anti-Tip Assembly

Anti-Tip Bracket

1/2 Screw

Bottom Bracket
B Plug in the microwave oven.
C Bottom bracket must be flat to the cutout floor to engage correctly with the anti-tip bracket as shown. Carefully slide the microwave back, making sure the power cord is not mashed or cut.
D Center the microwave oven within the cutout opening and slide the microwave oven in place, engaging the anti-tip bracket.
E Ensure the microwave oven is accurately centered.

6
.

INSTALLING THE TRIM FRAME

A Place the trim frame over the microwave oven.
B Make sure the trim frame is level and the microwave oven is centered within the trim frame. Mark four center positions through the four mounting holes of the trim frame.
NOTE: Center the trim frame equally on all four sides.
C Remove the trim frame and drill four pilot holes.

Pilot Hole

Cutout Opening

1 Screw

Trim Frame

Mounting Hole

D Attach the trim frame by using four screws.

Cutout Opening

1/2 Screw

Positioning Flange

F Drill pilot holes through the positioning flange and then install three 1/2 screws at the front of the bottom duct as shown.

7
.

REPLACE ANY LOOSE ITEMS

A Your trim kit is now fully installed. Replace any loose items that were removed from the inside of the microwave oven.
B Keep these installation instructions for future reference.
C Replace house fuse or close circuit breaker.

4