DELL OptiPlex Wi-Fi Wireless Network Antenna Cable Adapter Kit Installation Guide
- July 20, 2024
- Dell
Table of Contents
DELL OptiPlex Wi-Fi Wireless Network Antenna Cable Adapter Kit
Product Information
Specifications
- Product: OptiPlex
- Model: Tower, Small Form Factor, Micro
- Antenna Installation Guide
- April 2022 Rev. A00
Product Usage Instructions
Before You Begin
- Save and close all open files and exit all open applications.
- Shut down your system by clicking Start > Power > Shut down.
- Disconnect your system and all attached devices from their electrical outlets.
- Disconnect all attached network devices and peripherals from your system.
- If installing on a monitor, disconnect power and display cables, remove the stand, and place the monitor on a clean surface.
Tools Required
The procedures may require a Phillips screwdriver #2 for installation.
OptiPlex Tower Antenna Installation
- Follow the “Before You Begin” instructions.
- Align and connect the antenna cables to the SMA connectors on the chassis.
- Tighten the bolts to secure the antenna cables to the SMA connectors.
- Slide the SMA cover over the antenna cables.
- Align the tabs on the SMA cover with the slots on the chassis.
- Push the SMA cover towards the chassis until it clicks into place.
- Tighten the captive screw to secure the SMA cover to the chassis.
OptiPlex Small Form Factor Antenna Installation
Follow the same steps as for the Tower Antenna installation.
OptiPlex Micro Antenna Installation
Follow the same steps as for the Tower Antenna installation.
FAQ
-
Q: Do I need any special tools for installing the antennas?
- A: The installation may require a Phillips screwdriver #2.
-
Q: Can I install the antennas without disconnecting all devices?
- A: It is recommended to follow the “Before You Begin” steps to ensure a proper installation.
OptiPlex
Antenna Installation Guide
Notes, cautions, and warnings
NOTE: A NOTE indicates important information that helps you make better
use of your product.
CAUTION: A CAUTION indicates either potential damage to hardware or loss
of data and tells you how to avoid the problem.
WARNING: A WARNING indicates a potential for property damage, personal
injury, or death.
© 2022 Dell Inc. or its subsidiaries. All rights reserved. Dell Technologies, Dell, and other trademarks are trademarks of Dell Inc. or its subsidiaries. Other trademarks may be trademarks of their respective owners.
Before you begin
Steps
-
Save and close all open files and exit all open applications.
-
Shut down your system: Click Start > **Power > Shut down.
NOTE:** If you are using a Linux operating system, see the documentation of your operating system for shut-down instructions. -
Disconnect your system and all attached devices from their electrical outlets.
-
Disconnect all attached network devices and peripherals, such as keyboard, mouse, and monitor from your system.
CAUTION: To disconnect a network cable, first unplug the cable from your system and then unplug the cable from the network device.
If the system unit or the adapter is being installed on the monitor:- Disconnect the power and all the display cables from the monitor.
- Remove the stand from the monitor and place the monitor on a clean and soft surface.
Recommended tools
The procedures in this document may require the following tool
Phillips screwdriver #2
OptiPlex Tower Antenna
Steps
- Follow the instructions in Before you begin.
- Align and connect the antenna cables to the SMA connectors on the chassis.
- Tighten the bolts to secure the antenna cables to the SMA connectors on the chassis.
- Slide the SMA cover over the antenna cables.
- Align the tabs on the SMA cover with the slots on the chassis.
- Push the SMA cover towards the chassis until it clicks into place.
- Tighten the captive screw to secure the SMA cover to the chassis.
OptiPlex Small Form Factor Antenna
Steps
- Follow the instructions in Before you begin.
- Align and connect the antenna cables to the SMA connectors on the chassis.
- Tighten the bolts to secure the antenna cables to the SMA connectors on the chassis.
- Slide the SMA cover over the antenna cables.
- Align the tabs on the SMA cover with the slots on the chassis.
- Push the SMA cover towards the chassis until it clicks into place.
- Tighten the captive screw to secure the SMA cover to the chassis.
OptiPlex Micro Antenna
Steps
- Follow the instructions in Before you begin.
- Align and connect the antenna cables to the SMA connectors on the chassis.
- Tighten the bolts to secure the antenna cables to the SMA connectors on the chassis.
- Slide the SMA cover over the antenna cables.
- Align the tabs on the SMA cover with the slots on the chassis.
- Push the SMA cover towards the chassis until it clicks into place.
- Tighten the captive screw to secure the SMA cover to the chassis.
Antenna Placement
Place the antenna in a suitable location.
SMA antenna
For SMA antenna removal and installation procedures, search for OptiPlex
Service Manual at www.dell.com/support
Getting help
Contacting Dell
Prerequisites
NOTE: If you do not have an active Internet connection, you can find
contact information on your purchase invoice, packing slip, bill, or Dell
product catalog.
About this task
Dell provides several online and telephone-based support and service options.
Availability varies by country and product, and some services may not be
available in your area. To contact Dell for sales, technical support, or
customer service issues:
Steps
- Go to Dell.com/support
- Select your support category.
- Verify your country or region in the Choose a Country/Region drop-down list at the bottom of the page.
- Select the appropriate service or support link based on your need.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>