FARPOINT FLSL75204 2 Ft LED Linkable Shop Light Installation Guide
- July 15, 2024
- FARPOINT
Table of Contents
FARPOINT FLSL75204 2 Ft LED Linkable Shop Light
2 FT LED LINKABLE SHOP LIGHT
With Motion Sensor Link Up to 4 Lights
7500 LUMENS
Ultra Bright Natural White Light Installation and User Manual
2 FT LED LINKABLE SHOP LIGHT
SPECIFICATIONS
- Dimensions: 24″ x 10.75″ x 2″ (61 cm x 27.3 cm x 5 cm)
- Motion Sensor Up to 26 Feet (8 meters)
- 7500 Lumens 180 SMD LEDs (45 each panel)
- Long Lasting – 50,000 Hours Lifetime
- Ultra Bright Natural White Temperature 4000k
- Electrical Specifications: 120V, 60Hz, 70W
HARDWARE INCLUDED
- 2- V-Hooks
- 2- Ceiling Hooks
- 1- Cable Tie
- 4 – Screws
- 6- Wall Anchors
- 2- Chains 6″
WARNING: This product and or packaging can expose you to chemicals including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov. California Proposition 65 warning listed above is provided to California consumers to ensure compliance with California Proposition 65.
WARNING: RISK OF ELECTRIC SHOCK. Keep children away. INDOOR USE ONLY. Not rated for outdoor use. Should not be exposed to moisture or other outdoor elements. Not for use with totally enclosed luminaires. RISK OF FIRE: Do not exceed electrical ratings 120V 60Hz 0.8A 56W. cETLus Approved. Farpoint® is a Reg. Trademark of West Coast Imports, Inc. and may not be used without prior written consent. Features displayed are based on manufacturer specifications; actual specifications may vary. Artwork and design of this package is protected by U.S. Copyright Law. Altering or removing any trademark or copyright notice from this package is prohibited. Dist. by WCI, Inc. Commerce, CA 90040
Product Support: www.wciimports.com/product- support
INSTALLATION
Note: For the motion sensor to work properly, the Linkable Shop Light must be 9 to 11.5 feet from floor. Installation surface must be capable of supporting the shop light. Do not use with dimmers.
V-Hook & Chain Mount
Feed the end of one chain link through each V-Hook. Insert the V-Hooks through
the side holes and out the top (key holes) of the light. Attach the chain to
each of the two ceiling hooks on the ceiling. Make sure the light is level and
secure. Use the cable tie to secure the power cord.
Flush Mount
Install screws and anchors into ceiling. Slide the light into the screw heads
so that screw heads fit firmly inside the Light. Make sure the light is level
and secure. Use the cable tie to secure the nower cord..
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Increase the separation between the equipment and receiver.
- Consult the dealer or an experienced radio/TV technician for help.
To satisfy FCC/IC RF exposure requirements, a separation distance of 8 inches (20 cm) or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
OPERATION
The Linkable Shop Light is equipped with a motion sensor. Set to “O” to turn
OFF and set to “I” to turn ON.
Set the time to turn the light off.
Adjust the time delay (TIMER) as desired. The range is 50 seconds to 5
minutes. Turning the (TIME) counterclockwise (to -) will decrease time and
turning clockwise (to +) will increase time. The motion sensor will turn the
light on when motion is detected from 5 to 8 feet around the shop light. The
Linkable Shop Light should be installed 9 to 11.5 feet from floor.
CAUTION:
- This product contains high intensity LED devices. To prevent permanent eye damage, do not stare into the light beam at close range
- Carefully read and understand the information given in this manual before beginning installation. Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.
- Not rated for outdoor use. Should not be exposed to moisture or other outdoor elements.
- Do not dismantle this light. There are NO replaceable LEDs or serviceable parts.
- When using product, basic precautions should always be followed.
- Save these instructions and warnings.
- NEVER submerge this product in water!
- Do not use near hot surfaces.
- Do not use in areas near a gas source. Do not use with dimmers.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>