AITEMAY P20 Helmet Headset Instruction Manual
- July 11, 2024
- AITEMAY
Table of Contents
P20 QUICK MANUAL INSTRUCTION
P20 Helmet Headset
Switch on/off
Wireless connection
Voice assistant / lighting
Pairings
Connection conditions: the machines need the same model to be paired,
unlimited number of people within the effective distance.
First connection: after the two machines are switched on, press the mode key
to switch to single-channel intercom mode, when one of them needs to speak,
press and hold the single channel intercom key without letting go, it can
speak and let go to exit; when the other one to speak, the same operation can
realize the single-channel intercom.
Music function
Matching reset
Introduction to Wireless intercom connection operation (Single channel
Intercom and music sharing are tumed off by default every time you switch on)
I: Single channel Intercom mode (unlimited number of persons within
effective distance)
After the two machines are switched on, both short press the mode key to
switch to the single channel intercom mode, when one of them needs to speak,
press and hold the single channel intercom key without letting go, you can
speak, let go and exit; when the other one needs to speak, press and hold the
single channel intercom key without letting go, you can speak, let go and
exit, and so on and so on, and repeat the operation, you can realise the
single channel intercom.
II: Restore Factory Settings
Switch on the computer without connecting Wireless and Single channel
Intercom, press and hold the volume down and volume up buttons at the same
time for 5S, after the indicator light blinks fast, it restores the factory
settings and clears all the pairing information.
III: Music sharing (unlimited number of people within effective distance)
When both devices are switched on, both short press the mode button to
switch into music sharing mode. A mobile phone is connected to the device to
play music wirelessly, and the prompt tone “Music Sharing Transmit Mode” or
“Music shanng Receive Mode” is played. Start the music shanng pairing: one
device needs to be in the music sharing transmitting mode and other devices
are in the music sharing receiving mode. After the pairing ts successful, the
music sharing receiving mode terminal will have a successful connection prompt
tone accompanied by the “Music sharing connection success” prompt tone,
indicating that the music shaming ts successful. Please note that the music
sharing transmitting terminal will not have a successful connection prompt
tone. If two devices are connected to play music wirelessly, they can only be
shared by entering the music sharing transmitter.
IV: Telephone pnority
After switching on the machine, the machine is connected to Wireless, no
matter which mode the machine is in, when the machine calls or goes to the
phone, it will automatically enter the phone mode as a pnority, and after
hanging up, it will resume the corresponding mode.
Product Overview
Important Reminder:
Before installing the headset, please connect your mobile phone according
to the quick manual guide to test the sound effect and volume.
If there is a big difference in sound effect and volume after installing into
the helmet, please adjust the position of the speaker inside the helmet.
Single channel intercom schematic
Single channel intercom: only one channel can be allowed to enter the speaking state, and the others cannot be in the speaking state
Music Sharing
Telephone function
Product List
Caveat
- Please do not put the product into the open fire to avoid explosion;
- Please do not disassemble the product to avoid damage to the electronic devices;
- Please do not close to sharp objects to cause damage to the product;
- Long time no use, please place in a dry place;
- Before using the Wireless device, please fully charge it;
- If the red light does not come on when charging, it may be the voltage is too low;
- To extend the life of the built-in polymer battery, please charge the device at least once a month.
FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC RF warning statement: the device has been evaluated to meet general
RF exposure requirement, The device can be used in portable exposure condition
without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>