KitchenAid W11730247A Built In Refrigerator Handle Kit Instructions

: July 10, 2024
: KitchenAid

Table of Contents

KitchenAid W11730247A Built In Refrigerator Handle Kit
Specifications
Product Usage Instructions
FAQs
INTRODUCTION
How to read this diagram
INSTALLATION
Door Panel Installation and Alignment
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KitchenAid W11730247A Built In Refrigerator Handle Kit

Specifications

Width: 600 mm (23.5 inches)
Cabinet frame wall thickness: 16 mm minimum
Designed for use with custom wood panels with a thickness of 3/4 inch (19 mm)

Product Usage Instructions

Before You Begin
- The handle and handle mounting hardware must be installed before installing the custom wood panel. A qualified cabinet maker must perform the installation.
Parts and Tools Needed
- Parts Needed:
- Installation Kit supplied with Refrigerator
- Tee Nut
- Handle Mounts
- Handle – refrigerator door*
- Screw 10-24 X 1.000
- KitchenAid Badge
- Tools Needed:
- Tape measure
- Pencil
- Cordless drill
- 5/16 Drill bit
- 1/8 Hex key
- Torx T30 bit
- 11/32 socket driver
- Numbers may vary depending on the refrigerator model and handle type.
Installation Steps
- Verify panel dimensions before drilling any holes.
- For model-specific hole locations and spacing requirements, refer to Figure 1 and Figure 2 in the manual.
- Measure F’ from the top of the panel and measureG’ from the side of the panel. Mark the hole locations as shown in Figure 1.
- Drill a 5/16 hole in the two locations shown in Figure 1.
- Locate the supplied Screw and Handle Mount on the front side of the Panel, and attach the tee nut to the backside of the Panel in the locations shown in Figure 1.
- Place the Handle on the front of the panel and tighten the set screws located on the Handle Assembly using the Hex key provided.
- Note: Do not overtighten. Do not use an impact driver.

FAQs

Q: Can this handle kit be used with any type of refrigerator?
- A: No, this kit is designed to be used only with custom wood panels with a thickness of 3/4 inch (19 mm).
Q: What should I do if I don’t have all the tools listed for installation?
- A: It is recommended to gather all the required tools before starting the installation. Using the specified tools ensures proper installation and avoids damage to the handle or panel.

INTRODUCTION

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS, located in your appliance’s Owner’s Manual, before operating this appliance.
This manual covers several models. Your model may have some or all of the items listed. Refer to this manual or Frequently Asked Questions (FAQs) section of our website at www.kitchenaid.com/owner for more detailed instructions. In Canada, reference the Customer Service section at www.kitchenaid.ca/owners.

Door Panels Requirements (each door)

Maximum Weight: 26.5 lbs (12 Kg)

Minimum Panels Dimensions:

Refrigerator Door Panel: 417⁄8″ (1062.5 mm) x 23¼” (590 mm) x 3/4″ (20 mm)
Freezer Door Panel: 283⁄8″ (720.5 mm) x 23¼” (590 mm) x 3/4″ (20 mm) For maximum dimensions, please review the following diagram.

Cabinet frame wall thickness 16 mm

minimum R1 (mm)| B (mm)
594| 593| 592| 591| 590
A (mm)| 16| 0| 0| 0| 0| 0
17| 0| 0| 0| 0| 0
18| 0| 0| 0| 0| 0
19| 0| 0| 0| 0| 0
20| 0| 0| 0| 0| 0
21| 0.4| 0| 0| 0| 0
22| 2.6| 2| 1.3| 0.7| 0
23| 5| 4.4| 3.8| 3.2| 2.6
24| 7.5| 7| 6.5| 6| 5.5

How to read this diagram

For example if the door panel width dimension “B” is 593 mm and thickness of the door panel dimension “A” is 22 mm that means that the door panel requires a radius “R1” minimum of 2 mm.
BEFORE YOU BEGIN:

The handle and handle mounting hardware must be installed before installing the custom wood panel. A qualified cabinet maker must perform the installation.

IMPORTANT:

This kit is designed to be used only with custom wood panels with a thickness of 3/4″ (19 mm).
To avoid handle damage, lift the door and drawer panel(s) by the edges.

PARTS NEEDED:

Installation Kit supplied with Refrigerator (also sold separately; see your Quick Start Guide for Online Ordering Information).

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tape measure
Pencil
Cordless drill
5/16″ Drill bit
1/8″ Hex key
Torx✝ T30 bit
11/32″ socket driver

PARTS SUPPLIED:

Handle – freezer door
10-24 X 0.440 3–Prong Tee Nut
Handle Mounts
Handle – refrigerator door*
Screw 10-24 X 1.000
KitchenAid Badge

INSTALLATION

Install the Refrigerator Handle(s)

IMPORTANT:
- Verify panel dimensions before drilling any holes.
- For model-specific hole locations and the spacing requirements of KitchenAid handle mounting, refer to Figure 1 and Figure 2.
- NOTE: Figure 1 represents a (left-hinge) refrigerator door panel. Mirror the hole pattern around the vertical centerline for a left-hinge refrigerator door panel.

Measure ‘F’ from the top of the panel, and measure ‘G’ from the side of the panel. Mark the hole locations as shown in Figure 1.
Drill a 5/16″ hole in the 2 locations shown in Figure 1.
Locate supplied Screw and Handle Mount on the front side of the Panel, and attach the 3-prong tee nut to the back side of the Panel in the orientation and in the 2 locations shown in Figure 1. Tighten until 3 prong nut is fully seated but do not over-tighten.
Place the Handle on the front of the panel as shown in Figure 1 and tighten the set screws located on the Handle Assembly using the Hex key provided.
- NOTE: Do not overtighten. Do not use an impact driver.
- A. Door panel
- B. KitchenAid handle
- C. Bottom surface of a door panel
- D. 10-24 X 0.44″ 3–Prong Tee Nut (1)
- E. 3713/16″ (960 mm)
- F. 2″ (50 mm)
- G. 2″ (50 mm)
- H. 10-24 X 0.44″ 3–Prong Tee Nut (1)
- I. 1/4-20 X 1.5″ Screw (1)
- J. Handle Mount (1)
- K. Handle Mount (1)
- L. 1/4-20 X 1.5″ screw (1)

Install the Freezer Door Handle IMPORTANT:

Verify panel dimensions before drilling any holes.
The goal is to center the handle on the panel.
Verify before drilling that the hole pattern is at the center.
For model-specific hole locations and the spacing requirements of KitchenAid handle mounting, refer to Figure 2.
NOTE: Figure 2 represents a (left-hinge) freezer door panel. Mirror the hole pattern around the vertical centerline for a left-hinge freezer door panel.

Measure from the bottom edge and side edge of the Door Panel as shown in Figure 2 to locate the bottom hole, then measure from the centerline of that hole (and side edge) to find the remaining hole location.
Drill a 5/16″ hole in the 2 locations shown in Figure 2.
Locate supplied Screw and Handle Mount on the front side of the Panel, and attach the 3-prong tee nut to the back side of the Panel in the orientation and in the 2 locations shown in Figure 2. Tighten until 3 prong nut is fully seated but do not over-tighten.
Place the Handle on the front of the panel as shown in Figure 2 and tighten the set screws located on the Handle Assembly using the Hex key provided.
- NOTE: Do not overtighten. Do not use an impact driver.
- A. KitchenAid handle
- B. Door panel
- C. 10-24 X 0.44″ 3–Prong Tee Nut (1)
- D. 23/8″ (60.3 mm)
- E. 10-24 X 0.44″ 3–Prong Tee Nut (1)
- F. 2″ (50 mm)G. 235/8″ (600 mm)
- H. Handle Mount (1)
- I. 1/4-20 X 1.5″ Screw (1)
- J. Handle Mount (1)
- K. 1/4-20 X 1.5″ Screw (1)

Install the KitchenAid Badge (optional)

Peel the paper off of the adhesive backing on the Badge. Locate the bottom of the badge, 33/4″ (95.3 mm) from the bottom of the Freezer Door, and centered on the door.

Door Panel Installation and Alignment

Door Panel Installation

Assemble the panel alignment tool by inserting the long arm of the main piece into the cutout of the smaller piece, and adjust it so that the base is at the appropriate height, aligned with the base of the surrounding cabinet doors.
Use a screwdriver to tighten the panel alignment tool’s 9.5 mm screw and hold it in place.

Freezer Door Panel Installation

Mount the panel alignment tool onto the freezer door. Align the smaller piece with the screws on the bottom of the door, and slide it to the left.
Peel the protective paper covers off of the adhesive pads on each freezer door panel mount. There are two adhesive pads on each of the four panel mounts.
At an angle, rest the base of the freezer door panel on the panel alignment tool.
Slowly tilt the panel to attach it to the adhesive pads on the panel mounts. Firmly press against the corners of the door to ensure that the panel is properly attached to the adhesive pads.
Attach the freezer door with a panel by using only the upper 4 screws. Loosen the panel alignment tool’s screw and remove the tool from the freezer door by sliding it to the right and off of the door.

Refrigerator Door Panel Installation

Mount the panel alignment tool onto the refrigerator door. Align the smaller piece with the screws on the bottom of the door, and slide it to the left.
Peel the protective paper covers off of the adhesive pads on each refrigerator door panel mount. There are two adhesive pads on each of the four panel mounts.
At an angle, rest the base of the refrigerator door panel on the panel alignment tool.
Slowly tilt the panel to attach it to the adhesive pads on the panel mounts. Firmly press against the corners of the door to ensure that the panel is properly attached to the adhesive pads.
Attach the refrigerator door with a panel by using only the upper 4 screws. Loosen the panel alignment tool’s screw and remove the tool from the refrigerator door by sliding it to the right and off of the door.

Door Panel Alignment

Align the refrigerator and freezer door panels horizontally by adjusting the 4 screws shown in the figure. Once all adjustments are done lock the screws.
Align the refrigerator and freezer door panels vertically by adjusting side brackets with the help of a screwdriver within 1 mm. Once all adjustments are done lock the screws.
- NOTE: Do not use an impact driver. Secure screws by hand.
After proper alignment, fix the remaining brackets.
Place the screw covers on the all brackets of the refrigerator and freezer doors.