Business Solutions MW09 WiFi 6 AX1800 Wireless Access Point User Manual

Business Solutions MW09 WiFi 6 AX1800 Wireless Access Point

Product Information

Specifications

• Model: MW09
• Version: 1.1
• WiFi Standard: WiFi 6 AX1800
• Antenna: 2×2 Dual Band
• Location: Outdoor
• Product Type: Wireless Access Point

Product Usage Instructions

Chapter 2: Before You Begin
Ensure computer settings are configured properly before hardware installation.

Chapter 3: Configuring Your Access Point
Configure the Access Point using either the Web Interface or the EnWiFi App.

Chapter 4: Building a Wireless Network
Choose the appropriate mode for your network – Access Point, WDS AP Mode, WDS Bridge Mode, or WDS Station Mode.

Chapter 5: Status
Check the main status, connection details, and real-time information of the Access Point.

Chapter 6: Network
Set up basic IP settings, configure the Spanning Tree Protocol, and adjust wireless network settings including SSID Profile and Wireless Security.

Chapter 8: Management
Access advanced settings, configure CLI settings, set up email alerts, manage time zone, schedule Wi-Fi, and utilize various tools for management.

Frequently Asked Questions (FAQ)

1. Q: Where can I find the Quick Installation Guide?
   A: The Quick Installation Guide is included in the product packaging.

2. Q: Can this Access Point be used indoors?
   A: No, this Access Point is designed for outdoor use.

3. Q: How do I reset the Access Point to factory settings?
   A: To reset to factory settings, locate the reset button on the device and hold it down for at least 10 seconds.

IMPORTANT
To install this Access Point please refer to the Quick Installation Guide included in the product packaging.

Chapter 1

Product Overview

KEY FEATURES

• Dual concurrent 802.11ax architecture and backward compatible with ac wave2/ac/a/b/g/n client devices.
• Advanced 1024-QAM allows Access Points to carry more packets one time could work for delivering high speed rate than the legacy 11AC Access Points
• Bi-Directional (DL/UL) OFDMA utilizes air resource for Access Points and client devices efficiency.
• Bi-Directional (DL/UL) MU-MIMO will reduce usage of airtime for each transmission between Access Point and client devices.
• 360° Dipole-directional antennas to achieve comprehensive coverage for networking client devices under a pervasive environment.
• Power source is complianced with 802.3at PoE Input for flexible installation and implementing remotely reset/reboot over 100 meters (328 feet).
• Robust housing with IP67 enclosure rated to deploy at extremely weather .
• Systemic and distributed management over Meter ezMaster, Skykey controller, and EWS Management switch without licensing or subscription fee.

Introduction
Meter Wireless Long Access Point solution MW09 is designed for deploying on the versatile indoor and outdoor application. To meet today’s requirement on varied networking environment, Meter would like to provide the solution as flexible, robust and effective as the organization they desire. The state-of- the-art OFDMA and MU-MIMO technology brings revolutionary connecting speed and bandwidth for diversity of multimedia applications. MW09 11ax solution engineers with powerful RF interfaces that support maximum 2×2 spatial streams with 1201 Mbps in 5GHz frequency band and 574 Mbps in 2.4GHz frequency band. With robust IP67 certified casing, these access points is designed to withstand harsh environment conditions including serve and prolonged exposure to sunlight, extreme cold, frost, snow, rainfall, hail and humidity.

DL/UL MU-MIMO with OFDMA via Beamforming
Be a prior AX solution, Meter MW09 is not only built in powerful RF interfaces, but it also features advanced Multi-Users Multiple input Multiple output (MU-MIMO) on both download side and upload side, which enhances a dramatic breakthrough in the performance and flexible transmission between Access Points and wireless client devices.
MU-MIMO allows multiple spatial streams to be allocated to different clients simultaneously, increasing totally throughput, reduce latency, capacity of the WLAN system and increase spectral efficiency on download side. Compared to download side, MU-MIM Oupload side will manage varied  client devices to contest air resource within a channel under a pervasive environment. The MU- MIMO upload side coordinates with OFDMA upload side to arrange different types of traffic for using a proper bandwidth within a channel. The intelligent technology will carry multimedia content and web browsing data easily without consuming more time on round-trip between AP and client devices. The smoothly transmission will reduce collision times and enhance capacity of air resource, as well as optimize users experience.
Beamforming is a standard in 11ax which allows Access Points to focus energy of multiple antennas to transmit to a particular client device in that direction of that client. The innovative technology significantly enhances the higher signal-tonoise ratio and greater throughput of that client higher signal-to-noise ratio and greater throughput of that client. Meter

Enhance Capacity and Efficiency
Compared to 11ac solution, 11ax solution could carry 4x symbol OFDM symbol which can be significantly enhanced efficiency and transmitting PHY rate, as well as extend coverage on both indoor and outdoor application easily. To carry more data at the same time, modulation has been expanded from 11ac 256-QAM to 1024-QAM which can be enhanced 25% capacity of bit and reduce error margin during delivering data. The other breakthrough innovation of 11ax is to introduced BSS coloring technology for marking different colors on each data which will allows client devices to stop receiving a frame and return to sleep mode as soon as they recognize these frames are not of interest to them. The benefit of BSS coloring also reduces channel interference and channel collision of an access point, as well as improve to transmit signal easily.

System Requirements
The following are the Minimum System Requirements in order to configure the device.

• Computer with an Ethernet interface or wireless network capability
• Windows OS (XP, Vista, 7, 8, 10), Mac OS, or Linux-based operating systems
• Web-Browsing Application (i.e.: Internet Explorer, Firefox, Safari, or another similar browser application)

Package Contents

**The package of MW09 contains the following items:***

• MW09
• Detachable Antennas -2.4GHz2/5GHz2
• Pole Mount Strap*2
• Mountng Screw Set*2
• Mountng Bracket
• Ground Wire and Screw Set

*(all items must be in package to issue a refund):

Technical Specifications

• Standard
  IEEE802.11architecture and backward compatible with ac wave2/ac/a/b/g/n client devices.

• Antenna
  External 2.4GHz5dBi2 and 5GHz5dBi2 detachable antenna

• Physical Interface
  1 x 2.5 Gigabit ethernet port supports 802.3at PoE Input

• LED Indicator
  Power
  LAN
  2.4GHz
  5GHz

• Power Requirements
  MW09 Include 802.3at PoE Adapter

• Operation Modes

• Access Point
  Mesh
  WDS AP
  WDS Bridge
  WDS Station

• Advance RF Management
  OFDMA-UL/DL
  BSS Coloring

• Distance Control (Ack Timeout)
  Multicast Supported
  Data Rate Selection
  Auto Channel Selection
  Auto Tx Power Selection
  Site Survey
  Fast Roaming (802.11k/v)
  Band Steering
  RSSI Threshold
  MU-MIMO-UL/DL
  Tx Beamforming-UL/DL

• Easily Management
  VLAN Tag / VLAN Pass-through
  Guest Network
  QoS: Complaint with IEEE 802.11e /WMM RADIUS Accounting
  Wireless STA (Client) connection list Traffic Shaping (Per SSID/User)
  Multi SSID
  Management VLAN
  VLAN per SSID
  E-mail Alerts
  WiFi Scheduler

• Intuitive Tools
  SNMP v1/v2c/v3 support
  MIB I/II, Private MIB
  Save Configuration as Default
  CLI Support
  WiFi-Scheduler/Auto Reboot
  E-mail Alert

• Reinforcement Security
  WPA3/WPA2 Personal/Enterprise
  802.1x Authentication
  Hide SSID in beacons
  MAC address filtering, up to 32 MACs per SSID Wireless STA (Client) connection list
  Https Support
  SSH Support

• Optimal Performance
  QoS-Complaint with IEEE 802.11e standard Power Save Mode (UPASD)
  Pre-Authentication
  PMK Caching
  Fast Roaming (802.11r)
  Multicast to Unicast
  1024-QAM both on 2.4GHz/5GHz

• Physical/ Environment Conditions

• Operating:
  Temperature: -20 °Cto 60 °C(-4 °F to 140 °F)
  Humidity (non-condensing): 90% or less

• Storage:
  Temperature: -30 °Cto 80 °C(-22 °F to 176 °F )
  Humidity (non-condensing): 90% or less

Physical Interface – MW09

Mechanical & Environment

• Length: 190 mm (7.48”)
• Width: 124 mm (4.88”)
• Depth: 47 mm (1.85”)
• Weight: 720g

*Above information is device Only

• Protection Level: IP67
• Surge Protection: 1KV
• ESD Protection: Contact 4KV / Air 8KV

1. 2.4GHz Antennas Detachable 5.17dBi 5GHz Dipole-directional Antennas
2. 5GHz Antennas Detachable 5.17dBi 2.4GHz Dipole-directional Antennas
3. LAN Port (802.3af/at PoE): Ethernet port for RJ-45 cable.
4. LED Indicators: LED lights for Power, LAN Port , 2.4 GHzConnection and 5 GHz Connection. The color of LED light and active behavior is as below.
5. Mounting Holes: Using the provided hardware, the AP can be attached to a wall or pole.

• The installation angle of antenna must be vertical to the ground.
• This equipment is not suitable for use in locations where children are likely to be present.

Chapter 2  Before You Begin

Hardware Installation MW09

1. Connect one end of the Ethernet cable into the LAN port (PoE) of the AP and the other end to the PoE port on the PoE adapter.
2. Connect the Power cord with the PoE Adapter and plug the other end into an electrical outlet.
3. Connect the second Ethernet cable into the LAN port of the PoE adapter and the other end to the Ethernet port on the computer.
4. Screwonthe provided antennas to the top of this device
5. When all the process is completed, the LED light will be active as below.

This diagram depicts the hardware configuration.

Mounting the MW09

Using the provided hardware, the device can be attached to a wall or a pole. The height should not exceed 2 meter.

Wall Mounting Kit
Screw Set 1

• Anchors: Φ6.6*16 mm

Bolts: Φ8*25mm *Pole Mounting Strap2*
-Φ6612.6 mm

Screw-Set 2

• Screw – X type: Φ13*42 mm
• Screw – P type: Φ5.8*32 mm

Wall mounting the MW09

• A. Determine where the Access Point to be placed and mark location on the surface for the four mounting holes of wall mount base.
• B. Use the appropriate drill bit to drill two 8.1mm diagram and 26mm depth holes in the markings and hammer the bolts into the openings. Screw the anhors into the holes until they are flush with the wall.
• C. Screw the included screws into the anchors.
• D. Slide the mount bracket into the slot of the Access Point.

Pole mounting the MW09

• A. Thread the open end of the Pole Strap through the two tabs on the Pole Mount Bracket.
• B. Lock and tighten Pole Strap to secure Pole Mount Bracket to the pole.

*The installation angle of antenna must be vertical to the ground.

Appendix

Appendix A – FCC Interference Statement
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. Section 15.204(b) states that an approved “transmission system” must always be marketed as a complete system including the antenna.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IMPORTANT NOTE:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 26 cm between the radiator & your body.

Appendix B – Professional Installation Instruction (FCC)
Installation Personal
This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.

Installation Location
Theproductshallbeinstalledatalocationwheretheradiatingantennacanbekept26cmfromnearbypersoninnormaloperationconditionto meet the regulatory RF exposure requirement.

External Antenna
Use only the antennas which have been approved by the applicant. The non- approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of FCC limit and is prohibited.

Installation Procedure
Please refer to user’s manual for the detail.

Warning:

In order to make sure that the final output power does not exceed the limit set force in relevant rules, please carefully select the installation position and the installation angle of antenna must be vertical to the ground. The violation of the rule could lead to serious federal penalty.

Appendix C – IC Interference Statement
Industry Canada statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Caution:
where applicable, antenna type(s), antenna models(s), and worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in section 6.2.2.3 shall be clearly indicated.

IMPORTANT NOTE:
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 26cm between the radiator &your body.

DETACHABLE ANTENNA USAGE
This radio transmitter (IC: 10103A-MW09 ) has been approved by ISED to operate with the antenna type listed below with maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Approved antenna(s) list
MW09

Appendix D
Professional installation instruction (IC)

1. Installation personal
   This product is designed for specific application and needs to be installed by a qualified personal who has RF and related rule knowledge.The general user shall not attempt to install or change the setting.

2. Installation location
   The product shall be installed at a location where the radiating antenna can be kept 26cm from near by person in normal operation condition to meet regulatory RF exposure requirement.

3. External antenna
   Use only the antennas which have been approved by the applicant.The non- approved antenna(s) may produce un-wanted spurious or excessive RF transmitting power which may lead to the violation of FCC/ISED limit and is prohibited.

4. Installation procedure
   Please refer to user’s manual for the detail.

5. Warning
   Please carefully select the installation position and make sure that the final output power does not exceed the limit set forcein relevant rules. The violation of the rule could lead to serious federal penalty.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>