Atlantic MD-Series Flexible Basin Plumbing Kit Instruction Manual

July 10, 2024
Atlantic

Atlantic MD-Series Flexible Basin Plumbing Kit

Atlantic-MD-Series-Flexible-Basin-Plumbing-Kit-product

Specifications

  • Product: Atlantic Flexible Basin Plumbing Kit (FFKIT1)
  • Designed for: TidalWave TT-Series and MD-Series pumps
  • Intended Use: Plumbing pumps to decorative features on Flexible Hardscape Basins
  • Includes: Fittings and silicone for installations
  • Warranty: One-year warranty for the original purchaser

Product Usage Instructions

Installation

  1. Install the bulkhead fitting and position the Flex Basin according to the provided instructions.
  2. Attach the pump discharge elbow to the TT-Series pump, ensuring a secure connection.
  3. Glue the included nipple into the tee assembly and position it opposite the threaded end.
  4. Insert the Cord Seal Fitting into the tee, allowing slack in the pump cord for maintenance.
  5. Align the tee downwards, tighten the union, and glue the pump discharge elbow into the assembly.
  6. Complete plumbing work on the backside of the wall by connecting a male thread adapter over the pump cord.
  7. Cut a piece of pipe to extend from the male thread adapter to the back of the wall and glue it securely.
  8. Connect a tee over the cord, aligning it towards the center of the back wall, and secure it with glue.
  9. Assemble a Cord Seal Fitting around the pump cord into the end of the tee.

ColorFalls and Spillways

Additional instructions for plumbing ColorFalls and Spillways are available. Refer to specific guidelines for these features.

Copper Bowls

Specific instructions for plumbing Copper Bowls are provided separately. Follow those guidelines for proper installation.

Introduction

Thank you for selecting an Atlantic Flexible Basin Plumbing Kit. Before using the Kit, please take a moment to review this manual. Atlantic also provides installation videos on the website www.atlantic-oase.com. We recommend that you review pertinent videos if possible before proceeding.
FFKIT1 Plumbing Kits are designed to seamlessly plumb TidalWave TT-Series and MD-Series pumps to decorative features on Flexible Hardscape Basins, and contain all the fittings and silicone needed to simplify installations.

Installation

Install the bulkhead fitting and position the Flex Basin in the block surround following the instructions included with the flex basin (figure 1). Attach the pump discharge elbow to the  TT-Series pump. Hand-tighten the assembly and orient the elbow so it is positioned over the pump body. Glue the included nipple into one of the long legs of the tee and glue the tee assembly into the union opposite the threaded end (figure 2).Screw the threaded end of the union into the bulkhead fitting. Pass the pump cord into the short leg of the tee and work the cord through the tee, union, and bulkhead fitting. The union may be disassembled if needed to facilitate cord passage. The Cord Seal Fitting will seal around the pump cord so it can pass through the plumbing without leaking. Disassemble the Cord Seal Fitting and slip the rubber gasket around the pump cord. Reassemble the Cord Seal Fitting Ensuring the molded-in nuts are facing towards the tee. Be sure to align the inner and outer halves at 90° to each other and then start the screws (figure 3).
Loosen the union as needed to orient the tee to a convenient position then push the Cord Seal Fitting into the tee, leaving enough slack in the pump cord to allow for pump maintenance and servicing. Tighten the Cord Seal Fitting. Align the tee downwards and tighten the union, then glue the pump discharge elbow into the union assembly (figure 4). Move to the back side of the wall to finish the remainder of the plumbing work. Slide a male thread adapter over the pump cord, apply silicone to the threads, and install the adapter in the bulkhead fitting. Then, measure and cut a piece of pipe to extend from the male thread adapter to the back of the wall. Slide the section of cut pipe over the pump cord and glue into the male thread adapter. Next,  slide a tee over the cord and glue that to the section of the pipe, aligning the side outlet of the tee towards the center of the back wall. Dissemble and reassemble a Cord Seal Fitting around the pump cord into the end of the tee (figure 5).

Atlantic-MD-Series-Flexible-Basin-Plumbing-Kit-
FIG-1

ColorFalls and Spillways

Apply silicone to a male thread adapter and install it into the Spillway. Measure and cut a short section of pipe to extend out from the male thread adapter to the back of the wall. Glue the short section of pipe into the male thread adapter and then glue an elbow, pointing downwards, to the end of the short section of pipe. Cut a 4-inch long piece of pipe and glue it into the bottom of the elbow. Place the rubber coupling over the short section of pipe and tighten to secure. Cut and attach the supply line between the tee and the rubber coupling to complete the plumbing (figure 6).

Copper Bowls

Set the Copper Bowl upside down on a piece of Styrofoam or cardboard packing to finish the plumbing. Apply silicone to the threads of the included plug and install the plug in the off-center inlet at the bottom of the bowl. Cut a 4 inch long piece of pipe and glue it into a male thread adapter. Then, install the male thread adapter with silicone into the center inlet at the bottom of the Copper Bowl. Place the rubber coupling over the short section of pipe and tighten to secure. Cut and attach the supply line between the tee and the rubber coupling to complete the plumbing (figure 7).

Atlantic-MD-Series-Flexible-Basin-Plumbing-Kit-
FIG-2

Warranty

This product carries a one-year warranty. This warranty is extended solely to the original purchaser commencing from the date of the original purchase receipt. A misused or abused product voids this warranty.

Warranty Claims
In case of a warranty claim, the complete Kit should be returned to the place of purchase accompanied by the original receipt.

FAQ

Warranty Information

Q: What is the warranty period for the product?

A: The product carries a one-year warranty from the date of the original purchase receipt for the original purchaser.

Warranty Claims

Q: How to process a warranty claim?

A: In case of a warranty claim, return the complete Kit to the place of purchase with the original receipt.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Atlantic User Manuals

Related Manuals