HOFSTEIN B085RTFJ52 Modern Outdoor Wall Light Instruction Manual
- July 9, 2024
- HOFSTEIN
Table of Contents
HOFSTEIN B085RTFJ52 Modern Outdoor Wall Light
Product Information
Specifications:
- Rated Voltage: 120V
- Frequency: 60Hz
- Maximum Bulb Wattage: 60W
Product Usage Instructions
-
Preparation
Before starting the installation process, ensure that the power supply is turned off and remains off throughout the installation. -
Installation Steps
-
Remove the screws on both sides of the lamp wall box using appropriate tools.
-
Detach the circular hanging plate of the lamp.
-
Secure the round hanging plate in the screw hole at the installation position using the hanging plate screws.
-
Connect the L wire (Live wire) of the lamp to the live wire of the power supply, the N wire (Neutral wire) to the neutral wire of the power supply, and the bare copper wire to the ground wire of the power supply using the wiring cap.
-
Attach the lamp wall plate onto the round hanging plate, aligning the hole centers.
-
Fix the screws on both sides of the wall box of the lamp to secure the lamp.
-
Gently rotate the glass and screw in an appropriate bulb into the lamp cap.
-
Screw the glass back on securely.
-
Once installation is complete, turn on the power switch to illuminate the lamp.
-
Additional Information
- The lamp is equipped with a Dawn to Dusk Sensor, which automatically turns on at night and off at dawn. Ensure it is directed towards an open space with sunlight for optimal performance.
- Avoid installing the lamp in an environment where objects constantly block sunlight or in areas that are always dark.
FAQ (Frequently Asked Questions)
-
Q: What should I do if the lamp does not turn on after installation?
A: Check the wiring connections to ensure they are properly connected. Make sure the power supply is active and try replacing the bulb if necessary -
Q: Can I use a bulb higher than 60W with this lamp?
A: No, it is recommended to use a maximum 60W bulb to prevent damage to the lamp and ensure safe operation. -
Q: How do I clean the lamp?
A: Use a clean, soft cloth to wipe the lamp. Avoid using harsh chemicals or cleaning agents that may damage the surface of the lighting fixture.
RELATED TO INSTALLATION
GENERAL
-
To ensure the success of the installation, be sure to read these instructions carefully before beginning.
-
Before installations, prepare the required tools, such as Blade screw driver, Adjustable wrench, Step ladder, Wire cutter.
-
All electrical connections must be in accordance with the National
Electrical Code. Qualified licensed electricians are required to conduct the installation of electrical wiring. -
The outlet box that is connected to the lighting must be directly supported by the building structure.
-
Before starting the installation, disconnect the power to prevent electrical shock.
NOTE :The important safeguards and installations appearing in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care are factors which can not be built into any product. There factors must be applied by the person(s) caring for and operating the fixture.
CAUTION
- Rated 120V/60HZ,bulb 60W maximum.
- Care should be taken to avoid damage to the surface of lighting and wire, wearing gloves are remanded when installing.
- Keep lighting away from acid, alkali and other corrosive chemical or gas, clean the lighting with clean soft cloth only.
- Installation must be carried out by qualified electrician only.
- Disconnect the power before installing, cleaning and replacing lighting.
- Never cover the lighting when power is connected.
INSTRUCTIONS
-
Take out all lamp parts. The picture below shows the exact items that you receive in this product. Please note that this picture may look different from the computer generate part table. The parts in the part table are not assembled but some parts in this part picture are assembled, so there may be fewer items in the picture than in the table.
-
Part Table
Please note : The parts in this table are completely unassembled, for illustrative purpose. In the actual product that you receive, some parts are assembled and attached together. -
Finish lamp installations according to below instructions
- WIRE CONNECTION DIAGRAM
- Wires meet safety standards are recommended to connect the supply circuit.
- CAUTION:FIRE RISK
CANOPY INSTALLATION
Please read all instructions carefully before you proceed to install ,make sure that the power supply is turned off and remains off until installation is completed. Please note that each part is marked with letter as below .Please proceed in an alphabetical order.
- Original electrical box
- Circular bracket
- Terminal cap
- Zero line (white)
- Ground wire
- Live wire (black)
- Bracket Screw
- Screw
- Lamp wallplate
- Before installing the lamp, use tools to remove the screws on both sides of the lamp wall box. Remove the circular hanging plate of the lamp.
- Then fix the round hanging plate in the screw hole of the installation position with the hanging plate screws. Connect the L wire marked on the lamp to the live wire of the power supply, connect the N wire to the neutral wire of the power supply, and connect the bare copper wire to the ground wire of the power supply using the wiring cap in the accessory assembly.
- Fix the lamp wall plate on the round hanging plate, Aligned the hole center on the both sides of the lamp wall plate and the round hanging plate.
- Use a tool to fix the screws on the holes on both sides of the wall box of the lamp to fix the lamp.
- Gently rotate the glass and screw down the appropriate bulb into the lamp cap. Screw the glass back on. The installation is completed, turn on the power switch, the light can be turned on.
It is Equipped With a Dawn to Dusk Sensor, Which Automatically Turns on at Night and Turns Off at Dawn. Needs to be Directed Towards the Direction of Open Space With Sunlight, and Cannot be Installed in the Place Where the Object is Always in Darkness or Cove.
( Note: The lamp can not be installed in the direction of the lamp probe light reflection environment, otherwise it will affect the normal use of the lamp.)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>