8BIT-LW01H Application Owner’s Manual

8BIT-LW01H Application

Specifications

• Product Name: 8BIT-LW01H
• Manufacturer: Xi’an Babbit Technology Co., Ltd.
• Chip: ASR6601
• Operating Frequency: 902MHz-928MHz
• Operating Voltage: 3.3V
• Transmit Power: +22dBm (maximum)
• Sensitivity: -136dBm @125Kz SF12
• Memory: 128KB FLASH, 16KB SRAM
• Modulation: LoRa
• Power Consumption: 1.3uA (sleep mode)f the 8BIT-LW01H module includes details

Specifications
The specifications of the module provide detailed information on its technical aspects such as operating frequency, voltage, power consumption, memory size, and modulation support.

FAQ :
Q: Can the 8BIT-LW01H module be used in smart agriculture applications?
A: Yes, the 8BIT-LW01H module can be widely used in smart agriculture scenarios due to its ultra-long-range communication capabilities and low power consumption.

Important Notice:

Copyright Notice
Copyright: Xi’an 8Bit Information Technology Co., Ltd.
This material and all content contained therein are the property of Xi’an 8Bit Information Technology Co., Ltd. and are protected by the laws of the People’s Republic of China and applicable international conventions on copyright laws. Without the written authorization of Xi’an 8Bit Information Technology Co., Ltd., no one shall copy, disseminate, distribute, modify or otherwise use part or all of the content of this information in any form, and the offender will be held accountable according to law.

No Warranty Statement
Xi’an 8Bit Information Technology Co., Ltd. makes no representations or warranties, express or implied, about any content in this document, and does not assume any responsibility for the merchantability and suitability for a particular purpose or any indirect, special or consequential loss.

Confidentiality Statement
The information contained in this document (including any attachments) is confidential. The Recipient understands that the Document obtained by the Recipient is confidential and may not be used for any purpose other than that specified, and that the Document may not be disclosed to any third party.

disclaimer
The Company shall not be liable for property or personal injury caused by the abnormal operation of the customer. Customers are requested to develop corresponding products according to the technical specifications and reference designs in the manual. The Company reserves the right to make changes to the contents of this manual according to the needs of technological development, and the changed version will not be notified before the announcement.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Exposure to Radio Frequency Radiation. This equipment must be installed and operated in accordance with provided instructions, and the antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
This Modular Approval is limited to OEM installation for mobile and fixed applications only. The antenna installation and operating configurations of this Modular, including any applicable source based time averaging duty factor, antenna gain and cable loss must satisfy MPE categorical

Exclusion
Requirements of 2.1091. if the host is marketed so that end users do not have straight forward commonly used methods for access to remove the module so that the FCC ID of the module is visible; then an additional permanent label referring to the enclosed module: Contains Transmitter Module FCC ID: 2BGK68BIT-LW01H or Contains FCC ID: 2BGK68BIT-LW01H must be used.

Maintain records

commands

Product Introduction

Product Overview
8BIT-LW01H is a LoRaWan module designed and developed by Xi’an Babbit Technology Co., Ltd., which is used for ultra-long-distance spread spectrum communication. The chip ASR6601 is a general-purpose LPWAN wireless communication SoC that integrates an RF transceiver, modem, and a 32-bit RISC MCU. The MCU uses an ARM core and operates at up to 48MHz. The 8BIT-LW01H module supports LoRa modulation.
The 8BIT-LW01H module provides ultra-long-range and ultra-low ower communication for LPW AN applications and can be widely used in many application scenarios such as smart metering, smart logistics, smart buildings, smart cities, and smart agriculture.

Functional features of the module:

• Stamp hole encapsulation
• Frequency bands: 902MHz-138MHz
• The operating voltage is 3.3V, and the theoretical maximum transmit power is +22dBm
• High sensitivity: -136dBm @125Kz SF12
• Spread spectrum factor: SF5/SF6/SF7/SF8/SF9/SF10/SF11/SF12
• 128KB FLASH，16KB SRAM
• Supports LoRa modulation
• Power consumption is as low as 1.3uA in sleep mode

Model description

 Specifications

Electrical characteristics

Digital port features

The input logic level

is low

| VIL| One| ****

One

| 0.2| V
The input logic level

is high

| VIH| 0.8| One| One| V
The output logic

level is low

| VOL| One| | 0.1| V
The output logic

level is high

| VOH| 0.9| One| One| V

RF parameters

Output power

mode| Band| minimum| Typical| maximum| unit
Transmit power             902.45MHz                                  22| dBm
Transmit power             915.00MHz                                  22| dBm
Transmit power             927.55MHz                                  22| dBm
Receiver sensitivity, modulation bandwidth, 125kHz
mode| | minimum| Typical| maximum| unit
SF7| | | -124| | dBm
SF8| | | -126| | dBm
SF9| | | -128| | dBm
SF10| | | -131| | dBm
SF11| | | -135| | dBm
SF12| | | -136| | dBm

Module application guidance circuit

Explanation

1. The customer’s antenna should be located at the corner or edge of the main circuit board and connected to the RF-ANT pin of the module through a microstrip line. The impedance matching of the microstrip line must be controlled at 50 ohms. The circuit needs to reserve a π matching circuit to optimize RF performance. The default R1 resistance is 0 ohms, and C1 and C2 are not soldered.
2. The power pins of the module need to be designed with 100nF and 10uF capacitors, as well as TVS components.
3. The IO port of the module needs to be connected in series with a resistor to suppress interference. If the IO port level of the control chip is not 3.3V, then the level-matching problem needs to be considered.

Exterior dimensions

Pin layout

List of functional pins

3

| ****

IO1

| Serial     data indication pin| ****

O

| The serial port of the module is used to notify the MCU when data is sent, and the pin outputs a 100us high pulse, and the high pulse

time can be set

5

| IO2 BOOT0| ****

Boot pin

| ****

I

| It is used to enter the boot when burning and pull

up the boot foot to enter boot-burning mode when the module starts

6| IO6

SWDIO

| SWDIO| /|
7| IO7

SWCLK

| SWCLK| /|
8| IO16

RXD

| Burn        the

serial RX

| I| It is used to receive data during firmware

burning

9

| IO17 TXD| Burning/AT serial TX| ****

O

| It is used to send serial port data during firmware programming and AT command

interaction

---|---|---|---|---

14

| IO60 LPRXD| AT        serial port

reception

| ****

I

| It is used for serial port reception during AT command interaction, and supports LPUART
15| RSTN| Reset pin| I| It is used for the hardware reset of the module
19| RF ANT| Antenna

interface

| /|

A summary of common AT commands

Apply pin recommendations

IO1 is used to wake up the MCU, when a module has data sending, IO1 first pulls up 100us to wake up the MCU, and then sends the data to the MCU.

Manufacture:Xi’an 8Bit Information Technology Co., Ltd.
Add:Room 10908-10909, Building C, Xi’an National Digital Publishing Base, West Section of Keji 6th Road,High tech Zone, Xi’an City, Shaanxi Province

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>