GADGETSWEAR Y17 Selfie Stick Instructions

GADGETSWEAR Y17 Selfie Stick Instructions

Product Information

Specifications

• Compliance: Part 15 of FCC Rules
• Conditions: Must not cause harmful interference and must accept any received interference
• RF Exposure: Meets general RF exposure requirement
• Usage: Portable exposure without restriction

Product Usage Instructions

Compliance with FCC Rules

Ensure that the device is operated by Part 15 of the FCC Rules to prevent harmful interference.

Interference Handling

The device must accept any interference received, including that which may cause undesired operation. Keep this in mind during device usage.

RF Exposure

The device meets general RF exposure requirements, allowing for portable use without restrictions. Follow general safety guidelines for RF exposure.

DESCRIPTION

REMOTE CONTROL OPERATION

Connect Bluetooth

Long press the on/off button. The LED light flashes blue, indicating that the phone is turned on. Then turn on the Bluetooth option of the phone, search for the device Bluetooth name: LY-2, dick to complete pairing, and the display shows that it is connected and completed.

REMOTE CONTROL OPERATION

1. Power on: Press and hold the camera button for 3 seconds to power on, and the indicator light will flash to enter the search state.
2. Bluetooth connection: Open the phone Bluetooth search for “LY-2” and click on the connection. After successful connection, the indicator light will tum off.
3. Take a photo: When the remote control is connected to the phone, dick the take photo button, and the indicator light will flash and take a photo.
4. After tuming on the device, connect Bluetooth and wait for 5 minutes without any operation. The device enters a low-power sleep state and can be awakened by any click. After 10 minutes of inactivity, disconnect the Bluetooth connection and automatically shut down.
5. Shutdown: In both power on and sleep mode, press and hold the camera button for 3 seconds, the indicator light will flash and turn off.
6. After restarting, Bluetooth will automatically reconnect and function normally.
7. The red light is always on during charging, but goes out when fuly charged, with a charging current of 100MA A Solution to the Problem of Individually Pressing the Remote Control to Increase Volume/Adjust Focus/or Not

Responding on Android System Mobile Phones

1. Open the camera to enter the photography interface.
2. Swipe left or find the camera settings.
3. Click on the volume button function.
4. Set the volume key function to shutter (do not select zoom or focus).
5. Individual mobile camera settings have different paths, please search for them yourself

HOW TO CLIP A PHONE

1. The direction of the small chuck is upward
2. Use your phone to push it out and clamp it in.

Attention: Do not use both hands to directly pull the chuck

REMOVING THE REMOTE CONTROL

CLIP ODD ROTATION

Flip freely horizontally and vertically, take photosRealizing multi-angle shooting

HOW TO OPEN THE QUADRUPED

Press PUSH at the bottom of the tripodPush button to open

PORTABLE STORAGE MODE

Small and portable, always portable

QUADRUPED MODE

Four-legged landing for more stability

PRODUCT PARAMETERS

• Color: black and white
• Clip phone size: 6.5-10cm

REMOTE CONTROL PARAMETERS

• Applicable system: compatible with Apple /Android/Hongmeng
• Bluetooth name: LY-2
• Remote control distance: 10 meters (30 inches)
• Battery: Polymer battery (150mAh)
• Charging current: 100MA
• Charging interface: Type-C
• Transmission frequency: 2.401GHZ-2.480GHZ
• Adapter charging voltage/current 5V/1-3A

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
The device has been evaluated to meet the general RF exposure requirement. The device can be used in portable exposure without restriction.

Frequently Asked Questions

Q: What should I do if the device causes interference?

A: If the device causes interference, try moving it to a different location or adjusting its orientation. Ensure other electronic devices are not causing interference as well.

Q: Can I modify the device?

A: No, any changes or modifications not approved may void your authority to operate the equipment. Contact the responsible party for compliance before making any modifications.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>