Tech2Go B34 Series Wireless Headphones Instructions

June 27, 2024
Tech2Go

Model: B34 Series
Wireless Headphones
CHARGE BEFORE USE

B34 Series Wireless Headphones

CHARGING THE HEADPHONES – MUST ALWAYS BE CONDUCTED BY AN ADULT

POWER ON/OFF

  • Press and hold the Multi-Function Button (MFB) for 3 seconds to turn headphones ON
  • Press and hold the Multi-Function Button (MFB) for 3 seconds to turn OFF.

BLUETOOTH PAIRING – MUST ALWAYS BE CONDUCTED BY AN ADULT

  • When the headphones are ON, they will automatically enter pairing mode.
  • Select T2G-B34′ on your Bluetooth-enabled device to connect.
  • Headphones will automatically connect to your Bluetooth device whenever it is in range.
    To manually pair, press and hold the MFB for § seconds to enter pairing mode. To reset Bluetooth, press the MFB 3 times while in paifing mode.

CONTROLS

  • Short press the MFB to play/pause audio.
  • Short press Next/Previous Track Buttons to navigate tracks.
  • Press and hold Volume Up/Volume Down Buttons to adjust volume.
  • Short press the MFB to answer/end an incoming phone call
  • Press and hold the MFB for 2 seconds to reject an incoming phone call.
    Note : Headphones will automatically power OFF after 60 minutes of no activity.

AUX CABLE

  • Use a 3.5mm aux cable (included) for optional wired listening. (Please use adult supervision when using an aux cable, greater than 100cm (39.37in) for wired listening.)

LED INDICATORS

  • LED flashes red/blue while in Bluetooth pairing mode, and flashes blue when connected.
  • LED flashes red when battery is low, glows solid red while charging, and turns solid blue when the headphones are fully charged.

To prevent possible hearing damage, do not listen at high volume levels for long periods.
WARNING : For your safety, do not use headphones If they would prevent you from hearing warning sounds,such as while reding a bike, crossing the street, etc.
IMPORTANT SAFETY INSTRUCTIONS – Do not use or charge this product near a water source, and clean only vith dry cloth, Do not block any ventilation openings. Keep product away from heat sources. Only use accessories spcified by the manufacturer. Never leave unattended when charging

‘GENERAL BATTERY PRECAUTIONS  – Never Use or charge a battery If i appears to be leaking, or n any way abnormal. Avoid charging battery when the temperature is not within 5°C – 35° C (41″ – 95° Fahrenheit). Never expose a battery to any liquid, or to excessive heat such as direct sunlight or it. Always keep batteries out of the reach of infants and small children. Always charge lithium devices on a non-flammable surface – wooden tables/ carpeted floors are not recommended charring surfaces.
WARNING/DISPOSAL OF UNIT – Do NOT attempt to change or disassemble the built-in battery. Doing 50 will void the warranty and could cause personal injury and damage to your device. Do not dispose of batteries in the household trash or fire. Always dispose of used bateries/electronics in accordance with the prevailing community regulations. To find a crop-off location near you, visit www.call2recycle.com THIS IS NOT A TOY.

FCC Information

This equipment complies with FCC RF radiation exposre limits set forth for an uncontrolled environment:
This device complies with Part 15 of the FCC Rules, operation is subject to the following two con 1 This device may not cause harmful interference, and (2) this device must accept any interference received, Including interference that may cause undesired operation.

  • Warning: Changes or modifications to this unit not expressly approved by the party responsible for complance could void the user’s authority to operate the equipment
  • NOTE: This equipment has been tested and found to comply with the fomites for a Class B digital device pursuant to Part 15 of the FCC Rules.

These imits are designed to provide reasonable protection against harmful interference in a residential instalation. This equipment generates, uses and can radiate radio frequency energy and, it not installed and used i accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee the interference wil not occur n a particular instalation. I this equipment owes cause harmul interference to radio or television reception, which can be determined by terming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

ISED Information

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
This device contains licence-exempt ransmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device,

This device comply with ISED RF exposure requirement, seers can obtain Canadian information on RF exposure and compliance.
‘Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAN ICES-3 (8) / NMB-3(8)
Distributed by Tech 2 Go, LLC
B3V 051026-4 Srnted in Crina

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals