IO HFCL 24GE4XS Managed Switch User Guide
- June 16, 2024
- IO HFCL
Table of Contents
IO HFCL 24GE4XS Managed Switch
Applicable on
- HSP-IO-24GE4XS-C2A
- IO 24-Port Non-PoE, L2 Managed Switch with 4×1/10G SFP+ Uplinks and Single AC Power Supply
- HSP-IO-24GE4XS-C2AH
- IO 24-Port Non-PoE, L2 Managed Switch with 4×1/10G SFP+ Uplinks and Dual AC Power Supplies
- HSP-IO-24GE4XS-C2PAH
- IO 24-Port PoE+, L2 Managed Switch with 4×1/10G SFP+ Uplinks and Dual AC Power Supplies
Introduction
- Thank you for choosing the 24-port L2 commercial Switch from HFCL Switching Platform (HSP). PoE Variants Suitable in an enterprise/telco/campus environment to connect PoE clients like Wi-Fi AP, CCTV, P2P, P2MP, IoT, etc.
- Non-PoE Variants Suitable to connect Small Cells / BTS, P2P/P2MP, etc. in a telco environment and Desktops/Servers, IP-Phone, etc. in an Enterprise/Campus environment.
Packaging Content
- 24 Port Switch Qty: 1 number
- Mounting clamps with screws
- Standard power supply cord (1.5m)
Bracket Assembly
- The assembly of brackets for Rack mounting is described in the below diagram for the 24 Port L2 commercial Switch model.
- Step 1. Secure the brackets to the device using the supplied screws from the Mounting Accessory.
- Step 2. Install the device in the rack using four rack-mounting screws. Ensure that you secure the lower rack-mounting screws first to prevent the brackets from bending due to the Switch’s weight.
- Step 3. If installing multiple Switches, mount them in the rack, one below the other, in any order.
- Step 4. Turn on the power supply in the Switch securely.
Login access
The console access to the Switch can be obtained via the console port using the RJ45 to DB9 serial port adapter. An administrator can access the device using the command line interface (CLI) with the following console port setting as part of the factory default configuration.
- Speed: 115200 bps | Data bits: 8
- Stop bit: 1 | Parity: none
- Flow control: Hardware
Product specification
24 Port L2 Managed Switch Specifications
Capacity| Switching: 128 Gbps,
Forwarding: 95.232 mpps
---|---
Port Configuration| 24×10/100/1000 Base-T Gigabit Access Ports (PoE+ variants
and Non-PoE variants)
Uplink Ports| 4×1/10G SFP+ Uplink Ports
PoE Feature| Smart PoE, PoE variants suitable as access or aggregation Switch
and deployment of Wi-Fi AP/CCTV/IP Phone
L2 features| Support 4094 VLAN IDs, 16K MAC Table
Security| L2, L3, L4 ACLs, 802.1X Authentication (RADIUS, TACACAS+)
Storm Control| Broadcast, Multicast, and Unknown Unicast
Management| CLI, Telnet, SSHv2, SNMP v1/v2/v3 and ZTP
Temperature| Operating: 0 to 55 degrees C
Power Input| 100V to 240V for AC
Port LED status
LED Label | LED Colour | Indication | Status |
---|---|---|---|
ACT | Green/Yellow | Yellow blinking | Non-PoE with activity |
Green blinking | PoE on with the activity | ||
Solid Green | PoE on with no activity | ||
OFF | Non-PoE with no activity | ||
LINK | Green/Yellow | Solid Green | Link Up at 1000Mbps speed |
Solid Yellow | Link Up at 100Mbps speed | ||
OFF | No Link |
System LED status
LED Label | LED Colour | Indication | Status |
---|---|---|---|
SM | Blue | OFF | The system is powered OFF |
Blinking | Power up sequence in the process | ||
Solid ON | The system is booted and operational | ||
ALM | Red | OFF | No alarms reported |
Blinking | Alarm reported | ||
Solid ON | Critical alarm reported |
Safety Precautions
Observe the following safety precautions to avoid damage to the Switch:
- Do not power the device during installation.
- Keep away from high-voltage cables.
- Do not power off the unit in the middle of an upgrade process.
- Do not open the enclosure.
- Part Number: QSG-04-0004 Revision: A
Contact Us:
- iosupport@hfcl.com
- hfcl.com
- io.hfcl.com
- 8, Commercial Complex, Masjid Moth, Greater Kailash-II, New Delhi- 110048
- HFCL Limited All Rights Reserved. HFCL and io by HFCL are trademarks or registered trademarks of HFCL Ltd. Specifications are subject to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>