CyberTAN JB413-A1 BT Module User Manual
- June 16, 2024
- CyberTAN
Table of Contents
CyberTAN JB413-A1 BT Module
Specifications
- Model Name: JB413-A1 Bluetooth Module
- Version: V0.4.1
- Author : Ethan Lo
- Bluetooth Standard(s): Bluetooth 4.1
- Bluetooth Operation Frequency : 2.4GHz
- Bluetooth Data Rates: Up to 3 Mbps
- Power Requirements: [Not specified]
- Dimensions : [Not specified]
- Regulatory Conformance : FCC Statement
- Normal Operating Temperature: [Not specified]
- Functional Temperature: [Not specified]
Product Usage Instructions
Overview
Basic Specifications
The JB413-A1 Bluetooth Module is equipped with Bluetooth 4.1 technology operating at a frequency of 2.4GHz, supporting data rates of up to 3 Mbps.
Mechanical Characteristics
Pin Numberings
The logical definitions of the module’s pins are depicted below:
Pinouts and Signal Descriptions
Pin Definitions
- [Not specified]
EMI Certification Notes
- [Not specified]
Regulatory Information
FCC Statement
- [Include the FCC statement here]
FAQ
- Q: What are the power requirements for the JB413-A1 Bluetooth Module?
- A : The power requirements for the module are not specified in the user manual.
- Q : What is the normal operating temperature range for the JB413-A1 Bluetooth Module?
- A : The normal operating temperature range is not provided in the manual.
Revision History
Related Documents
CyberTAN Technology, Inc.
- No. 99, Park Avenue III
- Hsinchu Science Park
- Hsinchu, Taiwan 30077
- R.O.C.
CyberTAN® is a registered trademark of CyberTAN Technology, Inc. Bluetooth® is
a trademark of the Bluetooth SIG. All other trademarks appearing herein are
the property of their respective owners. This document may contain privileged
that is the property of CyberTAN Technology, Inc. and the improper disclosure
of which is an offence punishable under law. fits document may be viewed and
used only by the individual or other entity that received it directly from
CyberTAN. Redistribution of this document in any form is strictly prohibited.
The products described in this document are not intended or designed for use
in any application involving risk of harm to persons or property. CYBERTAN
PROVIDES
THIS DOCUMENT AS-IS, WITHOUT WARRANTY OF ANY KIND. CYBERTAN DISCLAIMS ALL
WARRANTIES, EXPRESSED AND IMPLIED, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-
INFRINGEMENT.
OVERVIEW
The CSR8811 WLCSP is a product from CSR’s Connectivity Centre. It is a single- chip radio and baseband IC for Bluetooth 2.4GHz systems including EDR to 3Mbits/s and Bluetooth low energy. CSR8811 WLCSP’s dual-mode radio enables it to connect to the billions of Bluetooth products already on the market, as well as a new generation of Bluetooth low energy devices. When used with CSR Synergy® Software and a CSR UniFi ® wireless chip, CSR8811 WLCSP provides a system fully qualifiable to Bluetooth v4.1 for faster file transfer.
Features
- Fully qualified Bluetooth® v4.1 system
- Full-speed Bluetooth operation with full piconet and scatternet support
- Class 1 Bluetooth power level supported
- High-sensitivity Bluetooth receiver
- On-chip SBC encoding
- On-chip balun
- Low-power selectable 1.2 to 3.6V 1/0
- Integrated 1/0 and core regulators
- High-speed UART port (up to 4Mbps)
- PCM/12S digital audio interface
- Support for IEEE 802.11 Coexistence
- HFP v1.6 wide-band speech supported on-chip
- Optimised for use on low-cost PCBs
- 28-ball 2.57 x 3.21 x 0.6mm 0.5mm pitch WLCSP
- Green (RoHS compliant and no
Basic Specifications
Table 1: Basic Specifications
MECHANICAL CHARACTERISTICS
Pin Number
The logical definitions of the module’s pins are depicted below
Pin Out Definitions
The logical definitions of the module’s pins are depicted below
Module Dimensions
PIN AND SIGNAL DESCRIPTIONS
Pin Definition
Table 2 : Pin Definition
EMI CERTIFICATION NOTES
It is recommended that the module be entirely encased in metal shielding to ensure meeting FCC and CE requirements.
REGULATORY INFORMATION
FCC Statement
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference instructions, which may cause harmful interference in radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Conne the squireen into an out equine circle district from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located with any other transmitters except in accordance with FCC multi-transmitter product procedures. Referring to the multi-transmitter policy, multiple-transmitters) and module(s) can be operated simultaneously without C2PC This device is restricted for indoor use.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator & your body.
IMPORTANT NOTE
This module is intended for OEM integrators. This module is only FCC-
authorized for the specific rule parts listed on the grant, and the host
product manufacturer is responsible for compliance to any other FCC rules that
apply to the host not covered by the modular transmitter grant of
certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.Additional testing
and certification may be necessary when multiple modules are used. 20cm
minimum distance has to be able to be maintained between the antenna and the
users for the host this module is integrated into. Under such a configuration,
the FCCradiation exposure limits set forth for a population/uncontrolled
environment can be satisfied. Any changes or modifications not expressly
approved by the manufacturer could void the user’s authority to operate this
equipment.
USERS MANUAL OF THE END PRODUCT
In the user’s manual of the end product, the end-user has to be informed to
keep at least 20cm separation with the antenna while this end product is
installed and operated. The end user has to be informed that the FCC radio-
frequency exposure guidelines for an uncontrolled environment can be
satisfied. The end-user has to also be informed that any changes or
modifications not expressly approved by the manufacturer could void the user’s
authority to operate this equipment. This device complies with Part 15 of FCC
rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following
“Contains TX
FCC ID: N89-JB413A1V1″. This device complies with Part 15 of FCC rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference and
- this device must accept any interference received, including interference that may cause undesired operation.