scheppach GP1400 Garden Pump Instruction Manual

scheppach GP1400 Garden Pump

Product Information

Specifications

• Dimensions: 450 x 230 x 280 mm
• Power Supply: 230 V~ / 50 Hz
• Power Consumption: 1300 W
• Flow Rate: 6000 l/h
• Max. Head: 48 m
• Max. Pressure: 4.8 bar
• Max. Suction Depth: 8 m
• Protection Class: IPX4
• Weight: 9.85 kg
• Noise Level: 85 dB

Product Usage Instructions

Unpacking

• Remove all packaging materials from the product.

Assembly

• Place the product on a stable, level surface.

Mounting a Suction Line:

• Attach a suction hose to the pump according to the provided diagram.

Preparing for Operation:

• Ensure the product is fully assembled before use.
• Electrical Connection
• Always disconnect the power plug before making any adjustments to the product.

Cleaning and Maintenance

• Clean and perform maintenance tasks with the power plug removed.
• Clean the product after each use.

Storage

• Store the product in a dry and safe place.

Disposal and Recycling:

• Dispose of packaging materials responsibly.

Frequently Asked Questions

Q: The pump is not drawing water, what should I do?

Possible Causes and Solutions

• No power supply – Check for power supply
• Pump impeller blocked – Disassemble and clean pump impeller
• Suction valve not   in water – Place suction valve in water
• Air in suction line – Bleed air from the suction line
• Suction valve leaking – Clean suction valve
• Suction valve clogged or dirty – Clean or replace the suction valve
• Rapid water level drop – Lower the suction valve or replace the suction valve components

symbols

Explanation of the symbols on the product

• Symbols are used in this manual to draw your attention to potential hazards.
• The safety symbols and the accompanying explanations must be fully understood.
• The warnings themselves will not rectify a hazard and cannot replace proper accident prevention measures.

Introduction

Manufacturer:

• Scheppach GmbH
• Günzburger Straße 69
• D-89335 Ichenhausen

Dear Customer,

• We hope your new product brings you much enjoyment and success.
• Note: Per the applicable product liability laws, the manufacturer of this product assumes no liability for damage to the product or caused by the product arising from it.
• Improper handling
• Non-compliance with the operating manual
• Repairs carried out by third parties, unauthorized specialists
• Installing and replacing non-original spare parts
• Application other than specified
• Failure of the electrical system in the event of the electrical regulations and VDE provisions 0100, DIN 57113 / VDE0113 not being observed
• Note: Read through the complete text in the operating manual before installing and commissioning the device. This operating manual should help you to familiarise yourself with your product and to use it for its intended purpose.
• The operating manual includes important instruc-tions for the safe, proper, and economical operation of the product, for avoiding danger, for minimizing repair costs and downtimes, and for increasing the reliability and extending the service life of the product.
• In addition to the safety instructions in this operating manual, you must also observe the regulations applicable to the operation of the product in your country.
• Keep the operating manual package with the power tool at all times and store it in a plastic cover to protect it from dirt and moisture. They must be read and carefully observed by all operating personnel before starting the work.
• The product may only be used by personnel who have been trained to use it and who have been instructed concerning the associated hazards.
• The required minimum age must be observed.
• In addition to the safety instructions in this operating manual and the separate regulations of your country, the generally recognized technical rules relating to the operation of such products must also be observed. We accept no liability for accidents or damage that occur due to a failure to observe this manual and the safety instructions.

Product Description

(fig. 1)

1. Pressure connection
2. Transport handle
3. On/off switch
4. Bracket for screws
5. Water drain plug
6. Suction connection
7. Screw-on pre-filter cap
8. Pre-filter

Scope of delivery

Proper use

• The machine may only be used in the intended manner. Any use beyond this is improper. The user/operator, not the manufacturer, is responsible for damages or injuries of any type resulting from this.
• An element of the intended use is also the observance of the safety instructions, as well as the assembly instructions and operating information in the operating manual.
• Persons who operate and maintain the machine must be familiar with it and must be informed about potential dangers.
• In addition, the applicable accident prevention regula-tions must be strictly observed. Other general occupational health and safety-related rules and regulations must be observed.
• The liability of the manufacturer and resulting damages are excluded in the event of modifications to the machine.

Area of application

• For watering and irrigation of green areas, vegetable beds, and gardens.
• For operating lawn sprinklers.
• With a pre-filter for drawing water from ponds, streams, rainwater barrels, rainwater cisterns, and wells.

Pumped media

• For pumping clear water (freshwater), rainwater, or light detergent solutions / domestic water.
• The maximum temperature of the pumped liquid must not exceed +35°C.
• This pump must not be used to pump flammable, gaseous, or explosive liquids.
• The pumping of aggressive liquids (acids, lyes, silo seepage juice, etc.), as well as liquids with abrasive (sanding) materials (sand), must also be avoided.
• The machine may only be operated with original parts and original accessories from the manufacturer. The safety, operating, and maintenance specifications of the manufacturer, as well as the dimensions specified in the technical data, must be observed.
• Please note that our equipment was not designed with the intention of use for commercial or industrial purposes. We assume no guarantee if the device is used in commercial or industrial applications, or for equivalent work.

General safety instructions

• WARNING – Read all safety information, instruc-tions, illustrations, and technical data for this elec-tric tool.
• Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.
  Save all warnings and instructions for future reference. The term “power tool” used in the safety instructions refers to mains-powered electrical tools (with a mains cable) and battery-powered electrical tools (without a mains cable).

General safety instructions

• This product is not designed to be operated by persons (including children) with impaired physical, sensory, or mental capabilities, or who have insufficient experience and/or insufficient knowledge unless they are being supervised by a person who is responsible for their safety or they are receiving instructions about how this Product is to be used. Children should not be left unattended, to ensure they do not play with the power tool.
  Persons who are unfamiliar with the operating man-ual may not use the product. The product is not to be used by persons under the age of 16.

• The product must not be operated if there are people in the water.

• Keep children away from the running engine.

• Dispose of the packaging material properly.

• Do not use the product in the vicinity of combustible fluids or gases. There is a risk of fire or explosion if disregarded.

• The pumping of aggressive, abrasive (scouring), corrosive, flammable (e.g. motor fuels) or explosive liquids, salt water, cleaning agents, and foodstuffs is not permitted.

• Store the product in a dry place and out of reach of children.

• The temperature of the pumped liquid shall not ex-ceed 35°C.

• Do not work with a damaged, incomplete, or modified product without the consent of the manufacturer. Before commissioning, have a specialist check that the required electrical protective measures are in place.

• Supervise the product during operation to protect the pump from automatic shut-down and against running dry. Check the function of the float switch regularly (see chapter “Commissioning”). Failure to do so will invalidate warranty and liability claims.

• Please note that the pump is not suitable for continuous operation (e.g. for watercourses in garden ponds). Regularly check the product for proper function.

• Please note that lubricants are used in the product, which may cause damage or contamination due to leakage. Do not use the pump in garden ponds with fish or valuable plants. If lubricants leak out, they may contaminate the liquid.

• Do not carry or attach the product by the cable or hose.

• Protect the product against frost and running dry.

• Only use original spare parts and accessories and do not modify the product.

• Please read the information on “Cleaning, maintenance, storage” in the operating manual. All additional measures, in particular opening the product, must be carried out by a qualified electrician. In the event of repair, always contact our service center.

Electrical safety instructions

• The mains plug must remain freely accessible when operating the product.
• Before you put your new pump into operation, have it professionally checked:
• Earthing, connection of the neutral line, and residual current circuit breaker must comply with the safety regulations of the power supply companies and function properly.
• Protect the electrical plug connections from moisture.
• If there is a risk of flooding, fit the plug connections in the flood-proof area.
• Ensure that the mains voltage corresponds to the specifications on the type plate.
• Carry out the electrical installation under national regulations.
• Only connect the product to a socket with a residual current circuit breaker (FI switch) with a rated residual triggering current of up to 30 mA; Fuse at least 6 amps.
• Before each use, always check the product, cable, and plug for damages. Defective cables must not be repaired but replaced with a new one. Have prod-uct damages repaired by a specialist.
• If the connection cable of this product is damaged it must be replaced by the manufacturer or their cus-tomer services personnel or by a similarly qualified person, to avoid hazards.
• Do not use the cable to pull the plug out of the out-let.
• Protect the cable from heat, oil, and sharp edges.
• Do not carry or attach the product by the cable. Use only extension cables that are splash-proof and intended for outdoor use. Always unroll a cable drum completely before use.
• Check the cable for damage. Pull out the mains plug before all work on the prod-uct, in work breaks and when not in use.
• Mains connection cables shall not have a smaller cross-section than rubber hose lines with the desig-nation H07 RN-F. The cable length must be 10 m. The conductor core cross-section of the extension cable must be at least 1.5 mm2.
• Lubricants are used inside the pump and can contaminate the drained fluids if the product is improperly operated or damaged.
• WARNING! This power tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under certain circumstances.
• To prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their physician and the manufacturer of the medical implant before operating the power tool.

Residual risks

• The product has been built according to state-of-the-art and recognized technical safety rules. However, individual residual risks can arise during operation.
• Health hazards due to electrical power, with the use of improper electrical connection cables.
• Furthermore, despite all precautions having been met, some non-obvious residual risks may remain.
• Residual risks can be minimized if the “Safety In-structions” and the “Intended Use” together with the operating manual as a whole are observed.
• Avoid accidental starting of the product: the operating button may not be pressed when inserting the plug in a socket. Use the tool attachment that is recommended in this operating manual.
• This is how to ensure that your product provides optimum performance.
• Keep your hands away from the working area when the product is in operation.

Technical data

Subject to technical changes!

Noise

• Warning: Noise can have serious effects on your health. If the machine noise exceeds 85 dB, please wear suitable hearing protection.
• Information about noise level measured by EN ISO 3744:2010

Unpacking

• Open the packaging and carefully remove the prod-uct.
• Remove the packaging material, as well as the packaging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport damage. In the event of complaints, the carrier must be informed immediately. Later claims will not be recognized.
• If possible, keep the packaging until the expiry of the warranty period.
• Familiarise yourself with the product by employing the operating manual before using it for the first time.
• With accessories as well as wearing parts and replacement parts use only original parts. Spare parts can be obtained from your specialist dealer.
• When ordering please provide our article number as well as the type and year of manufacture for the product.

WARNING!

• The product and the packaging material are not children‘s toys! Do not let children play with plastic bags, films, or small parts! There is a danger of choking or suffocating!

Layout

• Warning! Always remove the mains plug before carrying out adjustments on the product.

Fitting of a suction line (Fig. 1)

1. Screw a suction hose (plastic hose at least 19 mm (3/4”) directly or with a threaded nipple to the suction connection (6) approx. 30.75 mm (T1”) of the pump.
2. Lay the suction line from the water pick-up point to the pump on a continuously rising slope. Please do not lay the suction line above the pump height. Air bubbles in the suction line will delay and prevent the suction process.
3. Attach the suction and pressure lines so that they do not exert any mechanical pressure on the pump.
4. The suction line should be located deep enough in the water to prevent the pump from running dry if the water level drops.
5. A leaking suction line will prevent the water from being sucked in due to air ingress.
6. Avoid sucking in foreign bodies (sand etc.).

Filling the pump with water (Fig. 3)

NOTE! To reduce the start-up time of the pump and to prevent air from being sucked in, the pump must be filled with water beforehand!

1. The suction line should already be fitted for this purpose to prevent water from flowing out of the suction connection (6).
2. Use the opening of the pressure connection (1) to fill the pump with water. Alternatively, water can be poured in through the opening of the pre-filter plug (7).
3. Slightly tilt the pump now and then, to avoid air being trapped.
4. Now, attach the pressure line as described in the next point.

Fitting of a pressure line (Fig. 1)

1. Connect the pressure line (at least 19 mm (3/4”)) directly or via a threaded nipple to the pressure connection (1) approx. 30.75 mm (T1”) of the pump.
2. During the suction process, open the shut-off devices (spray nozzles, valves, etc.) in the pressure line completely so that the air present in the section line can escape freely.

Startup

Attention! Always make sure the product is fully assembled before commissioning!

1. Place the product on a firm, level, and horizontal location.
2. Open the pressure line.
3. Connect the mains lead.
4. Switch the product on using the on/off switch (3). Suction can take up to 5 minutes at max. suction head.
5. Switch the product off at the on/off switch (3) when you have finished working.

NOTE! The pump must be tight at the inlet and outlet. Therefore, regardless of your chosen connection, use a Teflon or any other sealing tape.

Electrical connection

• The electrical motor installed is connected and ready for operation. The connection complies with the applicable VDE and DIN provisions.
• The customer‘s mains connection as well as the extension cable used must also comply with these regulations.

Damaged electrical connection cable

• The insulation on electrical connection cables is often damaged.

This may have the following causes:

• Pressure points, where connection cables are passed through windows or doors.
• Kinks where the connection cable has been improperly fastened or routed.
• Places where the connection cables have been cut due to being driven over.
• Insulation damage due to being ripped out of the wall outlet.
• Cracks due to the insulation aging.
• Such damaged electrical connection cables must not be used and are life-threatening due to the insulation damage.
• Check the electrical connection cables for damage regularly. Ensure that the connection cables are disconnected from electrical power when checking for damage.
• Electrical connection cables must comply with the applicable VDE and DIN provisions. Only use connection cables of the same designation.
• The printing of the type designation on the connection cable is mandatory.
• For single-phase AC motors, we recommend a fuse rating of C 16A or K 16A for products with a high starting current (from 3000 watts)!
• AC motor 230 V~ / 50 Hz
• Mains voltage 230 V~ / 50 Hz.
• Mains power connection and extension leads must be 3-core = P + N + SL. – (1/N/PE).
• Extension leads up to 25 m must have a minimum cross-section of 1.5 mm².
• The mains power connection must be protected with a max. 16 A fuse.

Connection type Y

• If it is necessary to replace the mains connection cable, this must be done by the manufacturer or their representatives to avoid safety hazards.

Cleaning and maintenance

• Attention! Only carry out maintenance, cleaning, and adjustment work when the mains plug is pulled out.
• We recommend that you clean the product directly after every use.
• Clean the product at regular intervals using a damp cloth and a little soft soap.
• Do not use any cleaning products or solvents; they could attack the plastic parts of the prod-uct. Make sure that no water can penetrate the motor.
• We recommend regular inspections and care for a long service life.
• Before extended periods of inactivity or through the winter, the pump should be thoroughly flushed through with water, emptied, and then stored dry.
• To empty the pump housing, loosen the water drain screw (5) and tilt the pump slightly.
• If there is a risk of frost the pump must be completely emptied.
• After longer periods of storage check the pump by switching on/off briefly to check that the rotor turns normally.
• In the event of the pump being jammed connect the pressure line to the water supply line and remove the suction hose. Open the water supply line. Switch the pump on for ca. two seconds several times. This method rectifies blockages in most cases.
• To clean the pre-filter (8), loosen the pre-filter screw (7) and remove it. Afterwards, clean it with clear water.

Storage

• Store the product and its accessories in a dark, dry, and frost-free place that is inaccessible to children. The optimum storage temperature lies between 5 and 30 ˚C.
• Store the power tool in its original packaging. Cover the power tool to protect it from dust or moisture. Store the operating manual with the power tool.

Transport

• Always use the transport handle (2) for transporting the product.

Repair & ordering spare parts

• After repairs or maintenance, make sure that all safety-related parts are installed and are in perfect condition. All parts which may cause injury must be kept where they are inaccessible to children or others.
• Attention: According to the German Product Liability Act, no liability is accepted for damage caused by improper repairs or by not using original spare parts. Such work should be performed by a customer service center or an authorized specialist.
• The same applies to accessory parts.
• Spare parts and accessories can be obtained from our Service Centre. To do this, scan the QR code on the front page.

Connections and repairs

• Connections and repair work on the electrical equipment may only be carried out by electricians.

Please provide the following information in the event of any queries:

• Type of current for the motor
• Machine   data-type  plate
• Engine data-type  plate

Important note in the case of repairs:

• For return delivery of the product for repair, please ensure for safety reasons that it is free of oil and fuel when it is sent to the service center.

Ordering spare parts

• Please provide the following information when ordering spare parts.
• Model designation
• Item number
• Type plate data

Service Information

• With this product, it is necessary to note that the following parts are subject to natural or usage-related wear, or that the following parts are required as consumables.
• Wearing parts*: Pre-filter
• may not be included in the scope of delivery!

Disposal and recycling Notes for packaging

The packaging materials are recyclable. Please dispose of packaging in an environmentally friendly manner.

Notes on the electrical and electronic equipment act [ElektroG]

• Electrical and electronic appliances do not belong in household waste but should be collected and disposed of separately.
• Used batteries or rechargeable batteries that are not installed permanently in the old appliance must be removed non-destructively before disposal. Their disposal is regulated by the Battery Act.
• Owners or users of electrical and electronic devices are legally obliged to return them after use.
• The end user is responsible for deleting their personal data from the old device being disposed of!
• The symbol of the crossed-out dustbin means that waste electrical and electronic equipment must not be disposed of with household waste.
• Waste electrical and electronic equipment can be handed in free of charge at the following places:
• Public disposal or collection points (e.g. municipal works yards).
• Points of sale of electrical appliances (stationary and online), provided that dealers are obliged to take them back or offer to do so voluntarily.
• Up to three waste electrical devices per type of device, with an edge length of no more than 25 centimeters, can be returned free of charge to the manufacturer without prior purchase of a new device from the manufacturer or taken to another authorized collection point in your vicinity.
• For additional take-back conditions of the manufacturers and distributors, please contact the respective customer service.
• In the case of delivery of a new electrical device by the manufacturer to a private household, the latter may arrange for the free collection of the old elec-trical device upon request from the end-user. Get in contact with the manufacturer’s customer service.
• These statements only apply to devices installed and sold in the countries of the European Union and which are subject to the European Directive 2012/19/EU.
• Different provisions may apply to the disposal of electrical and electronic appliances in countries outside the European Union.

Troubleshooting

• The following table shows fault symptoms and describes remedial measures in the event of your product failing to work properly.
• If you cannot localize and rectify the problem with this, please contact your service workshop.

valve in the water
No water in the pump housing| Fill the pump housing with water
Air in the suction line| Check the suction line for leaks
Suction valve leaking| Clean suction valve
Suction valve clogged| Clean suction valve
Max. suction height exceeded| Check suction height
Inadequate pump delivery| The suction height is too high| Check suction height
Suction valve dirty| Clean suction valve
Water levels dropping rapidly| Position the suction valve lower
Pump performance is reduced due to hazardous substances| Clean the pump and replace worn parts

PARTS

EU Declaration of Conformity

hereby declares the following conformity under the EU Directive and standards for the following article

Warranty

Apparent defects must be notified within 8 days from the receipt of the goods. Otherwise, the buyerís rights of claim due to such defects are invalidated. We guarantee our machines in case of proper treatment for the time of the statutory warranty period from delivery in such a way that we replace any machine part free of charge which provably becomes unusable due to faulty material or defects of fabrication within such time. To parts not manufactured by us, we only warrant insofar as we are entitled to warranty claims against the upstream suppliers. The costs for the installation of the new parts shall be borne by the buyer. The cancellation of the sale or the reduction of the purchase price as well as any other claims for damages shall be excluded.

• www.scheppach.com
• https://www.scheppach.com/de/service

Documents / Resources

| scheppach GP1400 Garden Pump [pdf] Instruction Manual
GP1400 Garden Pump, Garden Pump, Pump
---|---

References

• Kontakt & Service | scheppach | scheppach

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>