Haier HDW15U3S1 Built Under Dishwasher Installation Guide

Haier HDW15U3S1 Built Under Dishwasher

Product Information

Specifications

• Model: HDW15U3S1 & HDW15U3B1
• Type: Built-under Dishwasher
• Installation Guide: NZ AU
• Indoor use only
• Earthed appliance

Product Usage Instructions

Safety and Warnings

• Ensure all water connections are turned OFF before installation.
• Install the dishwasher between cabinetry for stability.
• Use new hoses supplied with the dishwasher for connections.
• Avoid exposure to freezing temperatures or weather.
• Do not use extension cords or multi-socket outlet boxes for power supply.
• Keep the power supply cord away from potential damage or stress.

Servicing:

• Only recommended repairs should be done by trained technicians.
• If relocating the dishwasher, keep it upright to prevent water spillage damage.
• Do not operate the appliance if damaged or with missing parts.

Installation Components Required

• 4mm / 6mm Allen Key
• Moisture protection tape
• Toe kick brackets (2)
• Pre-finished toe kick assembly
• Drain hose support
• Various screws and washers
• Sound seal and spacers

Frequently Asked Questions

Q: Can I use old hoses for connection?

A: No, only new hoses supplied with the dishwasher should be used to ensure proper installation and avoid damage.

Q: Can the dishwasher be operated if damaged?

A: No, do not operate the appliance if it is damaged, malfunctioning, or has missing parts to prevent further issues or hazards.

SAFETY AND WARNINGS

WARNING! Electric Shock Hazard

• Failure to follow this advice may result in electrical shock or death.
• This appliance must be earthed. This appliance has a cord with an equipment-earthing conductor and an earthing plug. The plug must be plugged into an appropriate outlet that is installed and earthed under all local regulations.
• WARNING – Improper connection of the equipment-earthing conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are unsure if the appliance is properly earthed.
• Do not modify the power supply plug provided with the appliance. If a different outlet is required have it installed by a qualified electrician. Do not use an extension cord, adapter plug, or multi-box.

WARNING Cut Hazard

• Failure to use caution could result in injury.
• Take care – panel edges are sharp.

Weight Hazard

• Failure to follow this advice may result in damage or personal injury.
• Do not attempt to lift this product unassisted.
• To reduce the risk of fire, injury to persons, or damage when using the appliance, follow the important safety instructions listed below. Read all the guidance before using the appliance.

Servicing

• Do not repair or replace any part of the appliance unless specifically recommended in this guide. All other servicing should be undertaken by a Haier-trained and supported service technician or qualified person.

Installation

• Ensure all water connections are turned OFF. It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Regulations.
• The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.
• The switched power outlet must be outside the dishwasher cavity so that it is accessible after installation.
• This dishwasher is manufactured for indoor use only.
• Care should be taken when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord and hoses.
• If the dishwasher is to be relocated from one installation to another it must be kept upright to avoid damage from water spillage.
• Make sure only new hoses are used for connection (supplied with the dishwasher). Old hoses should not be reused.
• Failure to install the dishwasher correctly could invalidate any warranty or liability claims.
• Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an unstable product, which may cause damage or injury.
• Do not operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged power supply cord or plug.
• Do not store or use petrol, or other flammable vapors and liquids in the vicinity of the dishwasher.
• Connect to a properly rated, protected, and sized power supply circuit to avoid electrical overload.
• Make sure that the power supply cord is located so that it will not be stepped on, tripped over, or otherwise subject to damage or stress.
• Do not install or store the dishwasher where it will be exposed to temperatures below freezing or exposed to weather.
• Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket outlet box) to connect the dishwasher to the power supply.
• This appliance must be earthed. In the event of a malfunction or breakdown, earthing will reduce the risk of electric shock by providing a path of least resistance to electric current.
• This appliance is equipped with a cord having an equipment-earthing conductor and an earthing plug.
• The plug must be plugged into an appropriate outlet that is installed and earthed under all local codes and ordinances.
• EARTHING INSTRUCTIONS – This appliance must be connected to an earthed metal, permanent wiring system, or an equipment-earthing conductor must be run with the circuit conductors and connected to the equipment-earthing terminal or lead on the appliance.
• Installation must comply with your local building and electricity regulations.
• Failure to install the custom panels correctly could invalidate any warranty or liability claims.
• Installation of this dishwasher requires basic mechanical and electrical skills.
• Be sure to leave these Instructions with the Customer.
• Installation must comply with your local building and electricity regulations.
• After the dishwasher installation, the Installer must perform the Final Checklist.
• Remove all packaging materials supplied with the dishwasher.
• If the product is installed in a motor vehicle, boat, or similar mobile facility, you must bring the vehicle, boat, or mobile facility containing the product to the service shop at your expense or pay the service technician’s travel to the location of the product.

COMPONENTS REQUIRED

TOOLS Not supplied

• Powered driver
• Phillips screwdriver
• Flat-head screwdriver
• Box cutter
• 5mm Allen key

Supplied

• 4mm / 6mm Allen Key

PARTS Supplied

• Moisture protection tape
• Toe kick brackets (2)
• Pre-finished toe kick assmebly
• Drain hose support
• 4 x 25mm screws (4)
• 4 x 13mm screws (5)
• 4.2 x 50mm screws (2)
• Washers (2)
• Sound seal
• Spacers (4)

PRODUCT DIMENSIONS

CABINETRY DIMENSIONS

depending on feet height

CLEARANCES

SERVICE ACCESS

• We recommend locating the service holes on either side of the Dishwasher as shown.
• If the holes are created through wood, ensure the edges are smooth and rounded
• If the holes are created through metal, ensure an edge protector is fitted.
• based on a cabinetry depth of 580mm
• depending on the adjustment of leveling feet

PLUMBING AND ELECTRICAL CONSIDERATIONS

• excluding plug
• standpipe install illustrated.
• Distance is the same for all plumbing installs.

Hose and cord lengths

• Your services can be installed on either the left-hand or right-hand side of the product in an adjacent cabinet. Refer to ‘Cabinetry preparation’ for service access requirements.
• The drain hose should not extend more than 4m. A longer drain hose will cause reduced performance.

Water connection

• The dishwasher should not be connected to a water system where there is no temperature control unless the system is fitted with a suitable tempering valve.
• The dishwasher must not be connected to an undersink high-pressure push-through hot water system, as damage to the system will result.
• Maximum water temperature: 60°C
• 3/4 BSP connector water inlet hose
• Ensure the water connection complies with local plumbing regulations.

Water pressure

• 0.03–1MPa

Electrical requirements

• Power voltage: 220–240V (50Hz)
• Maximum current intensity: 10A
• Total absorbed power: 1720–2050W

Anti-flood protection

• This dishwasher has anti-flood protection, which will stop the water from flowing in the event of a leak within the machine.

PRIOR TO INSTALLATION

1. Unpack product.
   • Dispose of packaging responsibly.
2. Ensure all minimum cabinetry and service specifications have been met and that all services will be accessible after installation.
3. Remove the install kit, any internal packaging, all rubber bands, and all tape.
4. Ensure the cabinetry floor is free from bumps and obstructions that could prevent the Dishwasher from sliding into the cavity.
5. Align the supplied moisture protection tape to the cabinetry as shown.
   • Ensure this area is free of debris before carefully applying the tape to the surface.

PUSH INTO CAVITY

1. Using a flat-bladed screwdriver, turn to raise the leveling feet. Level the rear, outside legs first followed by the front legs. Do not adjust the rear middle leg yet.
2. Remove both screw covers before partially pushing the product into the cavity, pulling the hoses through as you push to avoid crushing or twisting them. Take care not to bend the legs.
   • Push the product from the outside edges to avoid door damage.
3. Check the product sits level within the cavity.
   • If required, the rear middle leg can be adjusted from the front of the product using a 5mm Allen key.
4. Select the desired spacer width and cut to size. Remove the adhesive and fit two spacers to each side of the product.
   • Push the product into the cavity from the outside edges.

SECURE TO CAVITY

1. Loosely fit 2 x side fixing screws
2. If needed, adjust the Dishwasher within the cavity before tightly securing it in place. Replace the screw covers.
3. Secure to benchtop using 2 x screws if possible.
4. Align both sound seal sheets to the base of the dishwasher. If required, trim excess felt.
5. Ensure door swing is unobstructed before securing the seals using the provided washers and 4.2 x 50mm screws.

INSTALL TOE KICK

PRE-FINISHED TOE KICK

1. Measure the distance between the floor and the base of the door. Refer to the table and mark out the cut location.
   • Score at the marked height, snap off excess material, and smooth edges.
2. Ensure brackets are oriented correctly before fitting to the panel using 2 x screws per bracket.
3. Measure the toe kick depth: toe kick recess panel thickness toe kick depth
   • Use Z to determine which tooth to bend back on each toe kick bracket.
   • Align the brackets to the slots on the product and slide them into place.

CUSTOM TOE KICK

1. Mark the pilot hole locations for each bracket. Measure the center of the panel and mark 237mm to each side.
   • To determine the height of the brackets, measure the height of the lowest bracket hole against the toe kick panel.
2. Ensure brackets are oriented correctly before fitting to the panel using 2 x screws per bracket.
3. Measure the toe kick depth: toe kick recess panel thickness toe kick depth
   • Use Z to determine which tooth to bend back on each toe kick bracket.
   • Align the brackets to the slots on the product and slide them into place.

CONTINUOUS TOE KICK

1. Align toe kick to product and ensure all door swing clearances have been met.
2. Fit panel to surrounding cabinetry.

Ø38MM STANDPIPE INSTALLATION

1. Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to ‘Plumbing & electrical considerations’ for minimum install heights.
2. Pull the hose through the support guide and rest in the standpipe. Ensure the drain hose does not extend into water retained in the trap; an air gap is required to prevent wastewater from siphoning back into the tub.
3. Ensure the rubber washer is fitted when connecting the inlet hose to the tap. Hand-tighten into place.
   • Using a spanner or pliers, turn a further 180° to secure. Avoiding over-tightening.
   • Do not turn the water supply on. The Dishwasher must be powered on for the flood protection feature to be enabled.
   • Plug the product in.

SINK TRAP/WASTE TEE INSTALLATION

1. Install the drain hose support to the back wall, as close to the underside of the countertop as possible. Refer to ‘Plumbing & electrical considerations’ for minimum install heights.
2. Pull the hose through the drain hose support before threading the hose clamp onto the hose and fitting it to the sink trap. Secure to trap using the clamp. Ensure the hose is routed straight to the trap.
   • Unplug or drill out the waste tee before securing the joiner to the sink trap or waste tee.
3. Ensure the rubber washer is fitted when connecting the inlet hose to the tap. Hand-tighten into place.
   • Using a spanner or pliers, turn a further 180° to secure. Avoiding over-tightening.
   • Do not turn the water supply on. The Dishwasher must be powered on for the flood protection feature to be enabled. Plug the product in.

INSTALLER CHECKLIST

TO BE COMPLETED BY THE INSTALLER

Installation

• Check all parts are installed correctly and are secure.
• Ensure all packaging, tape, and rubberbands have been removed.
• Ensure all clearance gaps have been maintained.
• Ensure the Dishwasher is securely fastened to the cabinetry and the door opens and closes freely with no resistance.
• Ensure the panel is fitted correctly to the Dishwasher
• Check the spray arm is in place, mounted correctly, and rotates freely.

Plumbing

• Ensure any knock-outs or plugs in the drain connection have been drilled out and the drain connection has been made.
• The drain hose joiner must not support the weight of excess hose material. Keep the drain hose as fully extended as possible to prevent sagging. Any excess length of drain hose should be kept on the dishwasher side of the drain hose support.
• Ensure the inlet hose has supplied rubber washer fitted, and that it is tightened.
• If connecting the drain hose to the sink trap, ensure the high loop is a minimum of 150mm higher than the drain hose joiner.
• Water softener models: adjust the water softener setting from the default setting to suit the water hardness of the area. Refer to your user guide.
• Ensure the water supply is turned off until the power is connected and turned on. The Dishwasher must be powered on for the flood protection feature to be enabled.

Electrical

• Ensure all electrical tests have been conducted under local regulations.
• If the site is left without power after installation is complete, ensure the water supply is turned off to prevent flooding.

TEST OPERATION

1. Turn the power and water supply on and open the dishwasher.
2. Press to select Rinse.
3. Press to begin the cycle.
4. After the Rinse cycle has finished, ensure the dishwasher has run and drained correctly.

Complete and keep for safe reference:

• Model ———————————-

• Serial no. ————————————

• Purchase date —————————–

• Purchaser ——————————-

• Dealer Address ——————————-

• Installer’s name ———————————-

• Installer’s signature —————————

• Installation Company ————————–

• Installation date —————————-

• WWW.HAIER.COM.AU
  WWW.HAIER.CO.NZ

• 432475A (01205 06825)

Documents / Resources

| Haier HDW15U3S1 Built Under Dishwasher [pdf] Installation Guide
HDW15U3S1, HDW15U3S1 Built Under Dishwasher, Built Under Dishwasher, Dishwasher
---|---

References

• Home Appliances | Haier New Zealand
• Home Appliances | Haier Australia

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>