Stackable 9 Cube Organizer Installation Instruction Manual

Stackable 9 Cube Organizer Installation Instructions

BEFORE BEGINNING

• Please read all instructions carefully.
• Familiarize yourself with all parts (see “PARTS”) and check quantities.
• Follow all safety precautions (see “SAFETY PRECAUTIONS”).

SAFETY PRECAUTIONS

WARNING

• This unit contains small parts which could be a choking hazard for small children. Children should be under adult supervision at all times or serious injury could occur.
• Always unload unit prior to moving the unit. The weight of personal belongings can cause the unit to become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.
• Do not overload unit. If any shelf, top, or bottom of unit bows or bends, it is overloaded. The shelf, top, or bottom could collapse and cause serious bodily injury and/or damage to personal belongings.
• Do not climb or step on the unit. The unit may become unstable and either tip or collapse. Serious bodily injury and/or damage to personal belongings may occur.
• Do not mount or attach anything to the sides, rear or front of the unit as this can create a force which can cause the unit to tip. Serious bodily injury and/or damage to personal belongings may occur.
• Do not hang this unit on the wall. The product structure is not designed for wall hanging. Serious bodily injury, damage to personal belongings, and/ or damage to the wall may occur.
• All units must be secured individually to wall stud using L-Bracket and Wall Screw (#10 x 1-1/2”) provided. If wall stud is not accessible, consult your local hardware store for appropriate mounting hardware. Failure to do so may create an unsafe tipping hazard that could lead to serious bodily injury and/or damage to personal belongings.
• Follow proper safety procedures when using power tools and ladders.
• We recommend you protect your work surface during assembly to prevent scratching or damage to table tops, wood floors, etc.

PARTS

A. side panel (2)
B. top/bottom panel (2)
C. horizontal divider (2)
D. vertical divider (6)
E. back panel (5)

HELPFUL HINTS

PART IDENTIFICATION

PART IDENTIFICATION SAMPLE

Use “PART IDENTIFICATION” picture (in each step) and exploded view (on previous page) to identify parts!

Look for part letter “stamping” in unfinished edges of part.

• Note overall shape of part. Count and locate holes in each part.

FINISHED VS. UNFINISHED

It is important to understand how finished edges go together. Take a moment to lay out all the wood pieces and note the finished and unfinished (raw wood) edges. Arrange pieces so all finished edges are facing the same way. While assembling, take care to note in each diagram which way finished edges are facing. In general, all finished edges will face forward and all finished sides (large area of piece) will face up when product is fully assembled and upright.

• Unfinished surfaces are shaded in gray.

HAND TIGHTEN SCREWS

We recommend you hand-tighten screws. Use care not to overtighten if using power tools.

STEP 1. Push short dowels into top and bottom panels.

NOTE:

• See “HELPFUL HINTS” for aligning finished and unfinished edges!
• Install dowels into top/bottom panels as shown. Top/bottom panels are the same.

• Unfinished surfaces are shaded in gray.

STEP 2. Attach top/bottom panel to one side panel.

NOTE:

• See “HELPFUL HINTS” for aligning finished and unfinished edges!

STEP 3. Attach one set of vertical dividers.

STEP 4. Insert long dowels. Attach horizontal divider.

• Be sure to assemble with all finished edges to front!

NOTE:

• Push LONG dowels into vertical dividers.
• Push horizontal divider down over dowels. (Holes in horizontal dividers go all the way through.) Secure horizontal divider with two screws through side panel.
• Attach one set of vertical dividers, repeat steps 1 and 2 and attach another (final) set of vertical dividers.

STEP 5. Attach top fixed shelf, and attach other side panel.

• Be sure to assemble with all finished edges to front!

NOTE:

• Align holes in dividers with dowels in underside of top panel. Push together. Secure top panel with two screws through side panel.
• Secure top vertical dividers with two screws through top panel.
• Attach other side panel.

STEP 6. Push on screw covers. Attach back panels.

• Unfinished surfaces are shaded in gray.

NOTE:

• Lay unit so finished (front) edges face down (unfinished edges will face up).
• Push screw covers onto all screw heads.
• Position the back panels in a staggered pattern as shown.
• Nail the back panels into place through the holes provided, being careful not to angle the nails.

STEP 7. Install dowels or hole plugs.

NOTE:

• For stacking units: Insert dowels into top holes.
• For single unit: Place hole covers over top holes.

STEP 8. Attach unit to wall (at wall stud location).

WARNING All units MUST be fastened to the wall. When stacking units, the unit on the bottom must be attached to the wall first before setting another unit on top. Do not stack units more than 72” high.

NOTE:

• Align center of unit with wall stud.
• Place short end of L-bracket against wall/wall stud. Use 1-1/2” screw to secure L-bracket to wall stud.
• Use 1/2” screw to secure L-bracket to top panel.

Stackable 9 Cube Organizer Installation Instruction Manual – Download [optimized]
Stackable 9 Cube Organizer Installation Instruction Manual – Download

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>