Panda Wireless Inc LGPAU0F AXE3000 WIFI 6E USB Adapter User Manual
- June 27, 2024
- Panda Wireless Inc
Table of Contents
Panda Wireless Inc LGPAU0F AXE3000 WIFI 6E USB Adapter
Introduction
The Panda Wireless Tri-Band (2.4GHz/ 5GHz/ 6GHz) 802.11ax| USB Adapter is easy
to use and set up. If you are tired of dealing with all those messy wires to
connect a laptop or PC to your home or office network, this Panda Wireless
adapter is an ideal access
solution for wireless connection via your wirelessrouter to the. Internet.
Key Features
- Compatible with IEEE 802.11a, IEEE 802.11b, IEEE 802.11 g.
- IEEE 802.11n. IEEE 802.11ac and IEEE 802.11ax wireless standards
- Compatible with USB 2.0 and 3.0 interfaces
- Transmission Data Rate: up to 600 Mbps on the 2.4GHz band and 1200 Mbps on the 5GHz and 6GHz bands
- Supports WEP, WPA, WPA2 and WPA3 wireless authentication protocols
- Supports TKIP and AES data encryptions
- Supports infrastructure and Ad-Hoc modes
- Supported operating systems: Windows 10/11 and Linux distributions like Ubuntu, Linux Mint, etc.
Wireless Networking Overview
A typical Internet access application for the USB wireless adapter is shown in the following diagram:
There are two different ways to access the Internet:
- With a wireless adapter, you can receive and transfer signals via a wireless router, then pass them to a Cable/DSL modem, and then to a local Internet service provider.
- With a wireless adapter, you can receive and transfer signals via ocal AP (Access Point) or so-called WiFi Hotspot directly.
Package Contents
- Panda Wireless PAUOF 802.11ax USB Adapter
- CD
- USB 3.0 Cable For USB-C port
- User Manual
Product Warranty
Panda Wireless® warrants to the end user (“Customer”) that this adapter will be free from defects in workmanship and materials, under normal use and service, for twelve (12) months from the date of purchase from its authorized reseller. Information in this document is subject to change without prior notice.
Driver Installation for Windows 10/11
To install the driver of the USB adapter, please log into a user account with
the administrator’s privilege before you follow the installation instructions
below:
Tips: Please get the latest update for Windows 10/11 from Microsoft.
Please send an email to support@pandawireless.com if you don’t know how to do
it. The Panda PAUOF adapter will connect to a 6GHz WiFi network on a computer
running Windows 11 or higher.
Notes
- Due to frequent updates, the contents in the CD are probably outdated upon receipt. You can get the latest drivers and manuals on the Panda Wireless website: www.pandawireless.com.
- Some anti-virus/firewall software blocks Windows to load the drivers for the Panda adapter. i.e. Zone Alarm, AVG, Avast, Kaspersky, Bit Defender, etc. You need to uninstall the software before you install a driver for the Panda adapter.
Follow the instructions and prompts of the “Install Shield Wizard” to finish the driver installation:
- Select “I accept the terms of the license agreement” and then click “Next”
- Select “Install Driver Only” and click “Next”.
Notes
Select “Install driver and WLAN Utility” if you want to set up your computer
as a WiFi Hotspot/WiFi repeater with the Panda adapter.
- Click the “Install” to confirm the installation and then wait a while.
- Click “Finish” to finish the driver installation.
How to connect to your own
Plug the Panda Wireless® adapter into one of the USB ports of your computer.
For Windows 10/11
- You move the mouse to the lower right-hand corner of the screen.
- Select the wireless icon in the red rectangle and select your wireless network from the list.
- Click the “Connect” button to connect to your wireless network.
- If your wireless network has been configured with wireless security, enter the network password.
- The following is an example of password password-protected network.
- Your computer is connected to your wireless network if you see “Connected” next to your wireless network.
Product Specifications
Federal Communication Commission
Interference Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, under Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used by the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution
To assure continued compliance, (For example – use only shielded interface
cables when connecting to computer or peripheral devices) any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation. The 6 GHz device cannot be used for the
control of unmanned aircraft.
FCC regulations restrict the operation of this device to indoor use only. The
operation of this device is prohibited on oil platforms, cars, trains, boats,
and aircraft, except that operation of this device is permitted in large
aircraft while flying above 10,000 feet. The device has been evaluated to meet
general RF exposure requirements. The device can be used in portable exposure
conditions without RF restriction.
Note: The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. Such
modifications could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment must not be co-located or operating in conjunction with any
other antenna or transmitter. End-users and installers must be provided with
antenna installation instructions and consider removing the no-collocation
statement. Applications for equipment authorization of portable RF sources
subject to routine environmental evaluation must contain a statement
confirming compliance with the limits specified in § 1.1310 of this chapter as
part of their application.
CE Mark Warning
This is a class 8 product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
WEEE Regulation
To avoid the potential effects on the environment and human health as a result
of the presence of hazardous substances in electrical and electronic
equipment, end users of electrical and electronic equipment should understand
the meaning of the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste and have to collect such WEEE separately.
2023 Panda Wireless, Inc. All rights reserved. Information in this manual is subject to change without notice and does not represent a commitment on the part of the company. Panda Wireless, Inc. shall not be liable for any loss or damage whatsoever arising from the use of information or any error contained in this manual No part of this manual may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, electrical, mechanical, optical, chemical, including photocopying and recording. for any purpose without the express written permission of Panda Wireless, Inc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>