Skmei 1238 & 1215 Manual

: June 7, 2024
: Skmei

Table of Contents

Skmei 1238 & 1215 Manual
- Display and function keys
Features:
Button instructions
Operating instructions:
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Skmei 1238 & 1215 Manual

Display and function keys

Features:

Time calendar function
Normal Time: Hour, Minutes, Second, Day and Weekday;12/24 hr format;
Calendar ( Yr 2000-2099)
Week : English automatic display
Alarm function
The time of alarming :1 minute
Chime hourly
Countdown function
1/100 Second Chronograph ringing form Oto 59 : 59 : 99, with SPL function;
Stopwatch mode.
– On /off Pedometer function
– Smart step for 7 seconds
– Two types of pedometer: Time / steps/ average speed mode- sports time /calories/ mileage display mode
– Everyday 0:00(12:00am) ,the recording of sports will be back to zero automatically
– User Information settings: metric / imperial- weight- G-Sensor sensitivity.in59sec,
21-day automatic memory storage step function ;
Low-voltage prompt
TWO types backlight: EL
IC working Voltage: 3V

Button instructions

Press and hold for quickly adjust; Time mode- Pedometer mode–Step Memory(MEM) Mode
Under Setting mode , press and quickly change setting time.
[SET]
Press and hold 2 seconds to enter setting mode, press and quickly exit settings.
Press and quickly on/off alarm
Press to turn on/pause stopwatch
Press to downward check the history record, Press and hold for quickly inquire .
[UP]
Under setting mode,Press plus 1,press and hold for quickly adjust
Under Time mode, press to change the following mode: time – ALM – stopwatch
In pedometer mode, Press and hold 2 seconds on /off Pedometer function, Press and quickly to change the
following mode:Time / Total steps/ speed per hour display – exercise time / calories/ mileage display mode.
Press to upwa rd check the hi story record, Press and hold for quickly inquire.
[EL]
Press and quickly show backlight for 4 seconds.
Press and quickly turn on/ cancel SPL function or clear stopwatch

Operating instructions:

1.Reset or powe r on default di splay

Power on/ reset, All datas display for 2 seconds, then the sound “Bi” rings, backlight isn’t bright, the power
state detection one time.
Power on reset:

Power on reset

2. Time mode:

A. After reset default into time mode, the normal time display interface as shown below.

B. Alarm mode

Press [UP] to convert as following:

Alarm mode

The week display below:

C. Setting mode

Press and hold the [SET] for 2 seco nds to enter the time setting mode.
Press the [MODE] to Cyclically Switch the setting item: 12/24 hours format – hour – minutes – seconds
– chronological order – year – month – day – Chime hourly on/ off, then press [SET] to exit the setting
such as Picture (red part of the picture represents flashing) :

Setting mode

Press [UP] to increase the values, hold down [UP] for 2 seconds to increase quickly
Adjust the year, month, day, after exit settings, the week automatically updated after exit settings,
In time setting mode, if you do not perform any button within 30 seconds (except [ELI ),the watch will
automatically exit from settings, and then return to time mode;

3. ALARM MODE

A. In time mode

Press [UP] to ALM alarm mode.

B. Display mode

Press the [SET] to turn on/ off alarm. The alarm icon display on alarm

Display mode

In alarm display mode, no button operation ,does not automatically return to time di splay mode .

C. Setting Mode

Press and hold [SET] 2 seconds to enter the alarm setting , in setting mode ,press [ MODE] switch the
settings items: hour- minute and then press [SET] to exit the settings (red figure represents the flashing):

ALARM MODE

Enter the alarm setting mode, automat1ca11y open tne alarm, d1sp1ay alarm icon.
Press [UP] to increase the values, hold down [UP] for 2 seconds to increase quickly.
In setting mode,ifyou do not perform any button within 30 seconds (except [ELI ), the watch will automatically exit from alarm settings, and then return to alarm mode;

D. Ringing mode

When a larm time is reached, the alarm icon will flash ,and alarm tone will sound “BIBIBIBI” for 60 seconds,
press any button to stop the alarm.

4 . STOPWATCH MODE:

A. In alarm mode, press [UP] to switch stopwatch mode, the initial value:00′ 00″ 00;

B. Press [SET] to start/ stop stopwatch, press [EL] to zero when stop the time.

C. During the stopwatch timer, press [EL] to turn on the SPL function, “SPL” will flash on the screen, stopwatch
running, Press [EL] again to return to the stopwatch timer.

D. When start the SPL function and suspend the stopwatch, press EL key to back to timer, showing the stopped time.

E. Stopwatch reaching the maximum(59′ 59″ 99), the non-alarm prompted to restart the stopwatch timer.

NOTE: under turn on the SPL function , switch to other functions mode, automatically canceled SPL function ,
stopwatch to run continually. Daily alarm and hourly chime will not quit from SPL function.

STOPWATCH MODE

5. PEDOMETER MODE:

A. Display mode

Under the stopwatch mode, Press [MODE] to switch the pedometer mode.
In the Pedometer mode, Hold [UP] key for 2 seconds to ON/OFF pedometer function , when on pedometer
function, it will comes with pedometer signal.
Press [UP] to switch the display: Total time/steps/speed per hour- exercise time/calories/ mileage mode. As shown:

Display mode

Total time/steps/average speed: the time displays the up LCD screen, the steps display the middle LCD screen, the average speed displays the down LCD screen.
Exercise time/ca lories/mileage: the exercise time displays the down LCD screen, the calories displays the middle LCD screen, the mileage displays the up LCD screen.
Maximum:
1. Max step number :999999 Steps.
2. Maximum average speed: 99.99KM/H or 99.99MILE/H (Metric displays KM/H or imperial displays MILE/H)
3. Maximum time: 1999MIN.
4. Maximum calories: 99999.9KCAL.
5. Maximum mileage: 999.99KM or 999.99MILE
In two kinds of pedometer display modes, both can pedometer.
In the pedometer mode, hold [EL] key for 2 seconds, steps, calories, distance value will be return to zero automatically.
Every day 00:00 the sport record will be zero automatically at the end of day.

B. Setting mode

In each pedometer mode, hold [SET] key for 2 seconds to enter setting user information mode.
In the user information setting state, press [MODE] key to switch setting items: metric/ imperial- weight- step distance
– G-Sensor sensitivity, as shown:

metric / imperial : The default to metric, press [UP] key to switch the selected metric / imperial.Adjustment of metric / imperial system setting items, the weight and step distance restore the default value automatically;
Setting weight: the default value is 60KG(132LB), adjustable range:30-200KG / 66-440LB;
Setting step distance: default step distance is 70CM (28INCH) , adjustable range:30-150CM/12-59INCH
G-Sensor Sensitivity: default value: MID, the sensitivity level for choice: LOW- MIDDLE-HI.

Press [ UPI key increase the setting item value, press [ UPI key 2 seconds increase fast.metric/imperial and G-Sensor Sensitivity no fast increase function.
In the user information setting mode, no button operation for 30 seconds,(except [ELI key)automatically exit the setting mode
NOTE : Turn on the pedometer, Except M EM mode and In the user information setting mode,other modes (including the setting mode) all can count steps.

6. STEP MEMORY STORAGE MODE :

In pedometer mode,Press [UP] key switch to Step memory storage mode, the default value: 00;
The “MEM” display on the up LCD screen,sport record date display on the down LCD screen The steps,
calories and distance of the historical record display on the middle LCD screen with 1 second for the cycle of automatic switching display, as shown:

automatic switching display

Everyday 0:00.00, automatic record the day date into MEM.
When adjust the month,date,M etric / imperial , MEM date of the month ,date and distance of the historical
record and units will fellow to change too.
press [ UP] or [SET] check before /after historical record , hold for quickly adjust. Left arrow display can
increase , right arrow display can decrease, no display can not adjust
press [EL] for 2 seconds, historical record will be return to zero automatically. steps, calories, distance value
will be return to zero automatically, return to memory storage step mode
if you do not perform any button within 30 seconds (except [EL] key) , the watch will automatically exit from
memory storage step mode , and then return to time mode

7. Low power detection function :

Low power detection detect once every minute.
If the battery voltage less than 2.SV, the LCD will display the low power symbol ” OJ “
In low power mode, don! affect other function normal work.
Any mode, Low power detection function can be work.

8. EL Light

undergo a Power-On Reset , EL light not work.
Press EL light button ,the light keep 4 seconds , recalculate time on each press.
EL light can be work in any mode.