runcom Scope cam 2 User Manual

runcom Scope cam 2 User Manual

Instruction Diagram

1. WiFi Button
   

2. Powering on /off Switch

3. LED1 Red Light（Recording Status）/ Blue Light(WiFi Status)

4. LED2 Red Light( Recording Status)/ Green Light (Charging Status)
   

5. Type-C

6. Micro-SD Card Slot

7. MICROPHONE

Charging:

Type-C only supports DC 5V power supply, please use conventional phone charger or power bank.
Green light will turn on during charging, while it will tun off when it is fully charged.It takes about 2
hours to get fully charged.

Low Battey Reminder:

When the battery is lower than 8%, the camera vibrates 4 times continuously, 30s each vibration.

MicroSD Card

Capacity up to 128GB; High Speed SD card (Class 10/UHS-I/UHS-II/UHS-III )is highly recommended
Note: The camera only supports FAT32 or exFAT format, SD cards over 64GB must be formatted via the App.

Basic Camera Operation

  Start Recording|   Push button up,
LED1, LED2(Red Light) have a slow flash at 1s interval simultaneously
---|---
  Stop Recording|   Push button down,
LED1 and LED2(Red Light) turn off simultaneously
  Open WIFI|   Operation1: Long Pressing WIFI button 3s in recording status
Waiting for a connection: LED1( Blue light flashes slowly at 1s interval),
Connected: LED1(Blue Light is on)
  Operation2: Long Pressing WIFI button 3s in shutdown status
Waiting for a connection: LED1( Blue light flashes slowly at 1s interval)
Connected: LED1(Blue Light is on)
  Close WIFI|   Long pressing WIFI button 3s,
LED1 (Blue light) off, the camera turns off simultaneously
Forced shutdown|   Long pressing WIFI button 8s
  Abnormal Status|   No SD card or SD card abnormality, LED1,
LED2 have a quick flash simultaneously

Connection to the Computer

U Disk Mode:

Connecting to PC via TYPE-C to USB, the camera will enter into U disk mode automatically, recording indicator(red light） is on

WEBCAM/PCCAM/UVC Mode

Short pressing WIFI button to switch to WEBCAM/PCCAM/UVC mode in U disk mode, then Short pressing WIFI button can switch back and forth to U Disk or WEBCAM mode.
NOTICE: If the camera cannot be recognized after connecting to the computer, please confirm whether there is microSD card in Scope cam 2.
If the information in the SD card cannot be read normally, please replace the USB cable or retry the computer USB port.

APP

1. Long press WiFi button 3s, LED1(blue light) flashes, WiFi is started and waiting for connection.
2. Find the SSID connection of the Scope Cam 2 in the wireless network of the mobile phone and enter the password, after successful connection, firmware update/WIFI indicator（blue light) is constantly on
3. Default SSID: RCSC02_*****PW:1234567890

Android and iOS APP:

Search ‘RunCam App’ on Google Play/App Store, or download on our website: https://runcam.com/download/scopecam2

Firmware Upgrade

Firmware Upgrade Status (Blue light blinks)Ensure that the Scope Cam battery is more than 50% before the upgrade
Manually copy the firmware file (FWSCLITE.bin) onto the microSD card. Follow the instruction on
https://runcam.com/download/scopecam2
To get the latest features and best performance from your Scope Cam, make sure you are using the
most current camera software. You can update your firmware with the RunCam App or at
https://runcam.com/download/scopecam2

Parameter

Technical Support

Please visit: https://support.runcam.com/hc/en-us

Read More About This Manual & Download PDF:

References

• RunCam - RunCam Scope Cam 4K - download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>