LDARC Et Max Instruction Manual

LDARC Et Max Instruction Manual

ET MAX Configuration

Wheelbase：            185mm
KK Tower：            F4+OSD 4in1 20A BLheliS OFF/25/100/200mW 48CH
Camera：                 (1200TVL 1/3’COMS NTSC)
Motor：                   MB2204-2250KV
Prop：                     44.53
Weight：                 283g(not include battery and receiver)

Pack List

Frequency Table

KK Tower

Bule LED is channel (CH) indicator, flash 1~8 times mean CH-1~8.Green LED is band(BD) indicator ,flash 1~6 times mean
BAND-A~ F,Red is output power(PW)indicator, flash 1~3 times mean 25mW/100mW/200mW output power. In normal working state, quickly double-click button, R/G/B sync flash mean VTX turned off, and also quickly double-click can turn on the VTX.in normal working state, press and hold the key for 3s,only blue led flashes, now click the key change channel(CH).press and hold the key for 3s,only blue green flashes ,now click the key change band(BD) .press and hold the key for 3s,only red led flashes, now click the key change output power(PW).

Receiver Bind

AC900(S-FHSS+D16 non-EU) bind, transmitter(FRSKY X9D/Futaba T18SZ) RX2A PRO Bind(S.BUS),transmitter(FLYSKY FS-i6) -3- Bind: Check receiver mode before bind ,the first blink after power on indicate the setting, is S-FHSS, is D16 (non-EU) FUTABA S-FHSS BIND: Turn on the TX then power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key. Bind procedure is completed and the receiver is working normally when green LED is solid FRSKY D16(NO Telemetry) BIND :Power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key, then set your TX into D16 bind mode. red LED solid meaning bind finished, exit TX from bind mode, receiver’s green LED solid meaning working normally

RX2A PRO Bind(S.BUS),transmitter(FLYSKY FS-i6)

BIND:Power on the receiver while pressing the key,green LED fast blink meaning already in bind mode,user can release the key, then set your TX into bind mode.Green LED turn off and red LED solid mean bind finished,exit TX from bind mode,receiver’s green LED solid mean working normally.

FM800 bind (default S.BUS, nonsupport PPM), example (FUTABA T8FG)

1. Open remote control, hold receiver bind button to power
2. Green light constant lighting means bind success

Note:

$.BUS and CPPM mode switch
Close remote control, press bind button 6$ when red light flash, loosen until enter $.BUS and CPPM mode switch

1. Green light quick nashing, press bind button and disconnect power, power-on again, enter $.BUS mode
2. Green light slow flash, press bind button and disconnect power, power-on again, enter PPM mode
   

DSM bind, example (T-SIX)

1. Remote control in off state, bind button to power
2. Loosen until indicator light fast blink, enter to bind mode
3.  Open remote control bind mode, Indicator light constant lighting means bind success

Note 1:

OSM2 uses SPEKTRUM1024 or SPEKTRUM2048 protocol, according to the remote control model to choose corresponding serial port protocol (example T-SIX, set protocol as SPEKTRUM1024)

Note 2:

OSMX remote control bind to DSM2 and OSMX receiver, but DSM2 remote conlrol only bind to DSM2 receiver. DSM2: Old SPEKTRUM and JR remote control protocol, wiclely •used with good compatibilily. DSMX: Newest SPEKTRUM remote control protocol, DSMX backwards compatible DSM2

Product and Factory Code

  Name

|

  Factory Code

---|---
  ET MAX PNP|   PNP.ET MAX
  ET MAX KIT|   KIT.ET MAX
  ET MAX Canopy|   PART.ET MAX CANOPY
  C1200 Camera|   CAM.C1200
  MB2204-2250KV(CW)|   MB2204-2250KV(CW)
  MB2204-2250KV(CCW)|   MOTOR.MB2204-2250KV(CCW)
  KK Tower(3 Layer) 20A|   FLYTOWER.KK TOWER(3 LAYER) 20A
  4in1 ESC 20A(KK Tower part)|   ESC.KK TOWER 20A
  F4+OSD(KK Tower part)|   FC.KK TOWER(F4+OSD)
  VTX(KK Tower part)|   VTX.KK TOWER
  Wire(KK Tower part)|   PART.KK TOWER WIRE
  3 Layer Tower Screw(KK Tower part)|   PART.KK TOWER SCREW(3 LAYER)
  44.53 Prop(clear black)|   PROP.44.53
  4 Inch propeller bumper|   PART.4 INCH PROPELLER BUMPER
  Carbon plate(ET MAX part)|   PART.BOTTOM PLATE.ET MAX
  LED+Buzzer(ET V2/3S part)|   PART.LED+BUZZER(ET V2/3S PART)

Factory setting

The factory has already load the firmware, default angle mode, please set

directly

1. Open Beta flight

2. Click“ Calibrate Accelerometer”
   

3. Prot,open UART6 switchable and saved
   

4. Select ESC protocol“DSHOT600”，set up the receiver protocol, open LEDSTRIP,OSD,DYNAMIC,FILTER
   
   
   

5. 5.PID setting

6. 

7. Default angle mode, setting of receiver is 5th channel ARM(AUX1) 8.LED
   

8. LED setting, then saved
   

When the drone is not flying properly, try to load FC firmware, then restore factory settings

1. Open ，then click  ，select firmware
   

2. Click ，then click to download FW to FC， click after FW updating finish into setting menu
   Flip Over After Crash Setting
   

After Sale Service

1. Provide free reparation service when find the product defect after purchase.
2. Provide pay-needed reparation service when product damage because improper operation.
3. China customers please contact with the after-sales service, overseas client please contact the dealer.

PNP/RTF Test report ID :

Flight test                                                     Package check

• Flying in good condition                      PNP
• Camera OK                                         Frame
• VTX OK                                            All parts of the installation
• Insulating sleeves have been installed manual
• Complete accessories ,total packages

Read More About This Manual & Download PDF:

References

• vtx.in Domain Name Is Available to Buy - Domain Name Marketplace
• LDARC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>