MantelMount Pulldown TV mount Installation Guide

June 7, 2024
MantelMount

MantelMount Pulldown TV mount Logo

MM750 Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

Please read this entire manual before you begin. Do not unpack any contents until you verify all requirements on PAGE 3. If you have any questions, visit MantelMount.com or call (800)-897-9755.

WARNING!
This product contains small parts that can be a choking hazard. Do not let children play with any of these small parts! Keep children away from the work area during installation.

WARNING!
Do not let small children operate, pull on, or hang from MantelMount. Do not operate MantelMount when anyone is near or behind the mount. MantelMount is very strong and can result in crushing injuries.

WARNING!
MantelMount must be installed to a wall or structure that is able to hold five times the combined weight of all equipment. If you are unsure about your structure, a contractor must evaluate your installation.
WARNING!
Exceeding the weight capacity can result in serious personal injury or damage to equipment! The combined weight of all components must not exceed 110 lbs (50 kg).

CAUTION:
This product is intended to be installed by professional installation contractors, or persons familiar with the tools and methods required for this installation. If you are not sure about your ability to perform this installation, you must contact a professional. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.
CAUTION:
Do not use this product in any way, or for any purpose, that is not specifically described in these instructions. MantelMount is not responsible for damage or injury caused by incorrect installation or improper use.

IMPORTANT:
MantelMount has three different adjustments that must be made after the installation is complete in order to operate properly.

U.S. Pat. No. 8,864,092

MantelMount Pulldown TV mount Cover

MantelMount Pulldown TV mount MantelMount Pulldown TV
mount

Before you begin, please verify that all components are included and undamaged. If any parts are missing or damaged, contact MantelMount. Never proceed with missing or damaged parts! Layout all components and make sure you identify that each one has a match in the diagram. Some of the parts included will not be used during installation. Do not proceed if you do not understand and identify all of the components.
MantelMount Pulldown TV mount Overview 1MantelMount Pulldown TV mount Overview
2

Please verify that your installation meets all of these CRITICAL

requirements:

A
MantelMount is designed for use only with decorative fireplaces that are not the primary heat source for a house. Temperature at the front edge of mantle should never exceed 110° F.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
A B
Wall must be WOOD STUD FRAME only. There must be at least 2 studs available for mounting. Wall covering must not exceed 5/8 inch thick.
For other types of walls or other types of installations please visit the FAQ section at www.MantelMount.com.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
B C
Mantle must not extend from mounting surface more than 19 inches (22 inches for non-recessed installations). MantelMount can not extend past a mantel larger than 19 inches. Larger mantels will also reduce the amount of side-to- side swivel.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
C D
TELEVISION REQUIREMENTS:

  1. Weight must be below 110 pounds (56 Kg).
  2. Screen size larger than 50 diagonal inches.
  3. Mounting screw holes are VESA compliant. For non-VESA hole patterns, please visit the FAQ section at www.MantelMount.com.
    MantelMount Pulldown TV mount MantelMount Pulldown Installation
D

E
Note: This is not an installation step, only a verification. Do not use these dimensions during installation.
The space above the mantle must be taller than the TV. The required space depends on how far out the mantle extends. Refer to chart below and add this additional height to the TV height to determine if space is tall enough.

If mantle extends: This is required space height:
Less than 10 inches TV height plus 6 inches
10 – 14 inches TV height plus 8 inches
14 – 16 inches TV height plus 10 inches
16 – 19 inches TV height plus 15 inches

MantelMount Pulldown TV mount MantelMount Pulldown Installation
E

Use a Vertical Brace {27} to determine if your television is a flat back or an irregular back. An irregular back will require spacers and longer screws to fill any spaces between the Vertical Brace and the TV. The Braces must be parallel to your television screen.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
1 Choose the correct screw diameter and length for the TV. Hand-thread screw combination into the TV to ensure there is adequate thread engagement without hitting the bottom of threaded insert. Use only minimum amount of spacers (if required).
MantelMount Pulldown TV mount MantelMount Pulldown Installation
2
CAUTION:
Do Not use screws that are too long for the threaded inserts of Television. This can damage internal components.

Possible Screw Combinations shown with maximum spacer usage (if spacers are required).
MantelMount Pulldown TV mount MantelMount Pulldown Installation
3 IMPORTANT INFORMATION: The Vertical Braces {27} are a fixed distance higher than the bottom of the Lift Housing Frame {30}. This relationship can be used to calculate most mounting situations such as centering the TV in an alcove or mounting the TV at a specific height on the wall.
If you measure the distance from the bottom of your TV (or Sound Bar) to the bottom of the Vertical Braces {27} (see: page 5) you will automatically know the distance from the bottom of your TV to the bottom of the Lift Housing {30}.
You can use this information to install the Lift Housing on the wall in order to locate your TV to any specific height you desire.
Example: If the Vertical Braces are attached 10 inches from the bottom of the TV, then the bottom of the cutout opening should be 4 inches higher than where you want the bottom edge of the TV on the wall (10″ – 6″ = 4″).
If you are installing above a mantel, then your installation must still have the additional clearance for downward motion stated in the chart in Step 9.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
4

The Vertical Braces {27} are always mounted higher than the bottom of the TV. However, the Brace Extenders {28} will be mounted one of two ways:
Without a Sound Bar – The Brace Extenders are installed within a few inches above the bottom of the TV.
With a Sound Bar – The Brace Extenders are installed below the TV with enough room to install the Sound Bar onto the Horizontal Brace {29}.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
5 Attach the Vertical Braces {27} to the TV so the bottoms of the Vertical Braces are at least seven inches higher than the bottom of the TV.
If the holes on the TV are lower than the braces, install the lower screws through the Brace Extenders {28} using the included Spacers {12}.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
6 Attach the TV Horizontal Brace {29} to the Extenders {28}. Use the Vertical Braces to align the Extenders.
Attach the Extenders to the Vertical Braces {27}.
Attach the Center Handle {56}, making sure the Handle is within one inch from the bottom of the TV.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
7 Measure the distance from the bottom of the Vertical Braces {27} (not the Extenders) to the bottom of television or Sound Bar (not the Center Handle).
Write down this distance to use in Step 9.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
8

Determine the Vertical Position of the Housing:
This image at right shows that the further out a mantle extends, the more it will interfere with the arc of the lowering TV. The chart below gives clearance heights from the bottom of the TV to the top of various mantel sizes.
However, the MM750 Lift Housing {30} is often located even higher on the wall than the TV. To locate the TV so it has enough clearance and doesn’t hit the mantel, you will need to know how much higher the Housing is than the bottom of the TV. Then you can locate the Housing on the wall.
NOTE: If there is extra space available, due to a high ceiling for example, then these heights are only minimum requirements.

If mantle extends: Required Clearance:
Less than 10 inches Add 5 inches
10 – 14 inches Add 7 inches
14 – 16 inches Add 9 inches
16 – 19 inches Add 14 inches

MantelMount Pulldown TV mount MantelMount Pulldown Installation
9

Installation Options: Surface Mount

SURFACE MOUNT (non-recessed) installation using Horizontal Braces {31} to attach to existing wall studs, on top of existing drywall.
The Horizontal Braces can reach studs that are up to 34 inches (875mm) apart. They attach flush to the back of the Lift Housing {30}.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
10SURFACE MOUNT (non-recessed) installation onto stone or concrete walls using the six holes in the back of the Lift Housing {30}.
The wall must be solid stone or concrete that can hold five times the weight of all combined equipment. This surface must not be a facade or non-structural material. Use concrete anchors (not included) to attach the Lift Housing to the surface.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
11

Installation Options: Recessed using Horizontal Braces {31}

RECESSED installation using the Horizontal Braces {31} to attach to existing wall studs: The Horizontal Braces attach to the flange on the front of the Lift Housing {30}. The Braces can be located off-center to the Housing, if needed, to reach the nearest stud. Use the included Template to mark the location to cut the drywall. This installation is easiest when there is no center stud that needs to be cut to make room. Paintable Wall Covers {25} can be snapped onto the Horizontal Braces.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
12

Installation Options: Recessed using 2×4 Stud Brackets {21}

MM750 includes brackets that make it easier to install horizontal pieces of 2×4 bracing inside the wall. This is because all of the attachment holes in the Brackets can be reached for drilling and screwing simply by reaching through the opening that is cut for the Lift Housing {30}, see FIG. A.

When wall studs are far apart, or when a center stud needs to be cut, or when the cleanest look is desired, sections of horizontal 2×4 can be installed through the cutout. They provide a solid structure for the mount without the need for the Horizontal Braces {31}. The mount is attached with Lag Bolts through the holes in the front flange of the Lift Housing {30}.

The Stud Brackets can be attached with lag bolts, or bolts with nuts and washers. The hardware to attach the Stud Brackets is not included.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
13

Cutting a Center Stud:

When cutting a center stud, measure 1.5″ above and below the template mark before the opening is cut out. The drywall will hold the stud in place while it is cut. Plunge cut through the stud at both locations and attach the cut ends to the cross bracing when they are installed, see FIG. C.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
14MantelMount Pulldown TV mount
MantelMount Pulldown Installation 15 Note: If the Bracket is near the cutout opening, make sure to orient the attaching hardware away from the opening so they do not interfere with the Lift Housing {30}. This hardware is attached before the braces are installed into the wall, see FIG. B.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
16

Marking the Location for the Lift Housing {30}
Use the Template to mark the location of the Housing according to the height from step 9. Make sure the Template is level and centered. Mantel Mount is located in the same spot for all installations.
If you are surface mounting, you will only need to mark the corners, but for recess mounting you will trace the entire template to cut out the drywall.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
17

Install the Lift Housing {30}
Locate, Mark, and Pre-Drill Studs in the Wall. All holes must be pre-drilled with 7/32″ drill bit to a depth of 2.5 inches (65mm) including wall covering. Note: Wall covering (drywall) must not exceed 5/8″ thickness.
Install the Lift Housing to the wall using one of the options previously described.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
18

CAUTION:
Do Not overtighten Lag Bolts {13}. Tighten only until the washers are firmly against the Housing. Damage due to overtightening can cause property damage or injury.

THIS STEP REQUIRES TWO PEOPLE
Pull the Safety Braces out to the ready position as shown. You might need to flex them over the screws. Do not bend the Safety Braces.
Firmly and slowly pull down the Arm until the Lifting Mechanism is in a horizontal position. The second person must swing the Safety Braces upward until they grab the crossmember of the Upper Arm.
The Lifting Mechanism should stay at a horizontal position.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
19

WARNING:
DO NOT put hands into Lifting Mechanism while operating the mount. Severe Injury can occur due to pinching or crushing. Always use the Safety Braces when working near or inside MantelMount.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
20 ** Install the TV Frame {26} using 4 Screws {20} and Washers {11}. These screws can also be used to fine tune level the TV. Always remember to tighten.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
21
THIS STEP REQUIRES TWO PEOPLE**
Carefully hang the Television onto the TV Frame making sure that both hooks on the Vertical Braces {27} engage the TV Frame.
DO NOT allow the Television to drop far enough to cause the Lifting Mechanism to hit the mantle.
MantelMount comes pre-adjusted to reduce the possibility of contacting the mantle, but you should always be prepared to remove the television at this stage to make the proper correction.
If the Lift Housing {30} appears to be too close to the mantle, remove television. Go to STEP 17 and make an adjustment to the Bottom Stop position. Repeat this process until the Lifting Mechanism is a safe distance from the mantle when the TV is installed.
Some older TVs are not weight balanced. If the TV is much heavier on one side, slide the TV slightly sideways to balance and level the TV.
Attach with 4 Screws {18}.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
22

Adjusting for Television weight: With Safety Braces in place, use a socket wrench with an extension to adjust the long bolts inside the Lift Housing {30}. Take turns adjusting each side so they stay relatively even with each other.
Turn the bolts clockwise (AS SHOWN BELOW) to pull the Gas Springs down and increase the lifting force for heavy TVs, or turn counter-clockwise for lighter TVs. This adjustment can take several turns. Reference the sticker scale on each side for the weight of the TV. Each scale represents the TOTAL WEIGHT of the TV.
Adjust the bolt until the TV gently stays in the lowered position. When the mount moves with a neutral feel within the Safety Braces, un-latch the Safety Braces and check the mount operation throughout the full range of motion.
(TV and some components are not shown in these images for clarity.)
MantelMount Pulldown TV mount MantelMount Pulldown Installation
23MantelMount Pulldown TV mount
MantelMount Pulldown Installation 24 Verify the proper lifting performance: MantelMount lifting force is designed to keep the TV securely in the up position while also allowing the TV to gently rest in the down position. See the diagram below for the correct lifting adjustment.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
25

Adjusting the Hard Stops for Range of Motion:

Adjusting the Bottom Stop Position: Loosen the Locknuts and adjust the Bottom Stop screws to the desired stopping position.
There are two screws underneath the Lifting Mechanism. Turn these screws inward until they tighten at the desired lower position.
Tighten both locknuts after the adjustments are made.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
26 Adjusting the Side Swivel Stop Positions:
Loosen the Locknuts and adjust the Swivel Stop screws to the desired stopping positions, both left and right.
Tighten both locknuts after the adjustments are made.
Note: If no swivel is desired, it may be necessary to remove the locknuts and re-attach them on the other side of the Swivel Bracket so that the Screws can be threaded out to their maximum length.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
29 Removing unwanted Tilt:
The TV should be fairly vertical in the up position and parallel to the wall. If the TV is tilted slightly downward, back out the adjustment screw slightly as shown. Tighten the locknut after the adjustment is made.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
27 Attaching Cables:
If cables are attached using the Anchors {14}, ensure that cables are not near the pinching area of the TV Frame and swivel portion of the mount. If cables are near the swivel, loop them away from the pinch area securely.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
30 Reference Only: This is one possible configuration for the signal cables. Each segment of the cables has extra length so that the cables are not stressed or kinked when the mount is moved. Ensure that cables do not get pinched between brackets when the mount is raised.MantelMount Pulldown TV mount MantelMount Pulldown
Installation 31 **CAUTION:
Never release the handle before it is fully upright. MantelMount is strongest in the top position, and allowing it to slam closed can damage televisions. Always control the lifting process.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
32 ****
CAUTION:**
Never allow small children to play around or operate MantelMount. Property damage or personal injury can occur.
MantelMount Pulldown TV mount MantelMount Pulldown Installation
33

          MantelMount Pulldown TV mount MantelMount Pulldown Installation
34

ITEM NO. PAM NUMBER DESCRPTION QTY.
I 12189 M5x12 4
2 12193 M5 x 30 4
3 12191 MS x 40 4
4 12193 M6 x16 4
5 12194 446×30 4
6 12195 1.46 x40 4
7 12197 448×15 4
8 121% M8 x 25 4
9 12199 M8 x45 4
10 12166 Washer M6 4
II 14126 Washer M8 x 2
12 12122 Spacer 8
13 14137 Log Bolt Max 63 4
14 14110 Cable Toe Amin( 4
1S 12162 Cable Tie 8
16 12183 Locknut M6 6
17 12187 Locknut MB 8
18 12178 Round Saes M6 x 12 8
19 12255 Ibund Saew 446×40 4
20 12176 Fbund Saew Max 16 34
21 15023 Stud Becket 4
22 12186 Nut M8 7
23 21088 SocketCap Saew M8 x 25 3
24 210% SocketCap Same 143 x40 2
25 21143 Wag Cover 6
26 21050 1V Frame Welded 1
27 14338 Vertical BM! 2
28 14356 &ace Extender 2
29 14060 1N1 Horizontal Braze 1
30 21115 (recess Frame, 750,Welded 1
31 21039 Horizontal Berge 2
32 14115 %ling Sixng Mount 4
33 12247 Disk SpringWasher 1•13 4
34 21085 Adjustment Block 2
35 21180 Hex Bolt M8 x 160 2
36 12160 Gas Spring 4
37 21110 Upper Arm, 750 Welded 1
38 21081 Laver Arm Welded 1
39 21060 Suave! 1
40 21045 Tit Brecket,Wekkd 1
41 21044 Mle,750 1
42 21119 Busing 4
43 21037 Me 2
44 21121 Bushing 4
45 21092 Washer M8 x 3 x 24 2
46 21035 Me 2
47 21054 bp Prvot 1
48 21041 Connector Brea 1
49 21063 Bottom Pivot 1
50 21178 [bond Screw 1A6 x 15 2
51 21163 Set SaewM5x IS 2
52 21144 Round Screw M8 x60 1
53 21135 Safety WC! 1
54 21211 Warning Stsdier 1
55 21206 adjustment Sticker 2
56 14062 Center Mende 1
57 12222 Handle Rubbeaemix Change 2
58 21190 Cardboard Template 735x 335rnm 1
59 MM750M Instruction Manual I

Customer Service:
(800)-897-9755
www.MantelMount.com
MantelMount Pulldown TV mount MantelMount Pulldown Installation
35

MantelMount Pulldown TV mount MantelMount Pulldown Installation
36

Exclusive MantelMount Features!
Auto-Straightening: Flattens the TV as it is raised to the upper position to prevent rotation into the wall

Safety Braces: Hold the mount safely in the down position to work behind the TV during installation

Smooth Operation: Solid shafts with polymer bushings at each pivot point provide silent movement
Temperature-Sensing Handles: Change to red color at temperatures above 110ºF to warn users if the freplace is too hot for TV safety
MantelMount Pulldown TV mount MantelMount Pulldown Installation
36MantelMount Pulldown TV mount
MantelMount Pulldown Installation 38

Full Manufacturer Warranty:

MantelMount will replace or repair any product or part that proves defective due to improper workmanship or material during the warranty period. Visit www.MantelMount.com for details.
This Installation Manual is available for download as a PDF document at www.MantelMount.com. The PDF version can be used to see larger images or to zoom in for much greater detail.

U.S. Pat. No. 8,864,092 01Jan2018 MantleMount MM750

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals