IN LIGHT Integrated LED Vanity Light Installation Guide
- June 7, 2024
- IN LIGHT
Table of Contents
IN LIGHT Integrated LED Vanity Light Installation Guide
Package Contents
Warranty
5-YEAR LIMITED WARRANTY
The manufacturer warrants this product to be free from defects in materials
and workmanship for a period of five (5) years from date of purchase. This
warranty applies only to the original consumer purchaser and only to products
used in normal use and service. If this products is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at he manufacturer’s discretion, provided that the
product has not been damaged through misuse, abuse, accident, modifications,
alterations, neglect, or mishandling. This warranty shall not apply to any
product that is found to have been improperly installed, set-up, or used in
any way not in accordance with the instructions supplied with the product.
This warranty shall not apply to a failure of the product as a result an
accident, misuse, abuse, negligence, alteration, or faulty installation, or
any other failure not relating to faulty material workmanship. The
manufacturer specifically disclaims any liability and shall not be liable for
any consequential or incidental loss or damage, including labor/expense costs
involved in the replacement or repair of said product.
Contact the Customer Service Team at info@getinlight.com or visit www.getinlight.com
Safety Information
- To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
- Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
- For Residental installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
- DO NOT INSTALL DAMAGED PRODUCT!
- This fixture is intended to be connected to a properly installed and grounded UL listed junction box.
- These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purpose, this matter should be referred to Inlight Co. Ltd.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: RISK OF ELECTRICALSHOCK
- Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply.
- Turn off the power when you perform any maintenance.
- Verify that supply voltage is correct by comparing it with the luminaire label information.
- Make all electrical and grounded connections in accordance with the National Electrical Code and any applicable local code requirements.
- All wiring connections should be capped with UL approved wire connectors.
CAUTION: RISK OF INJURY
- Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
- Avoid direct eye exposure to the light source while it is on.
- Account for small parts and destroy packing material, as these may be hazardous to children.
WARNING: RISK OF BURN
- Allow fixture to cool before handling. Do not touch enclosure or light source.
- Do not exceed maximum wattage marked on luminaire label.
- Follow all lamp manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement, and recycling.
CAUTION: RISK OF FIRE
- Keep combustible and other materials that can burn away from luminaire and lamp/lens.
Pre-Installation
PLANNING INSTALLATION
Compare all parts with the parts listed in the package contents section. If any part appears missing or damaged, do not install and use this light. Contact customer service.
CONSULT A LOCAL LICENSED ELECTRICIAN OR ELECTRICAL CONTRACTOR IF YOU ARE NOT SURE ABOUT THE INSTALLATION.
TOOLS REQUIRED
● Phillips Screwdriver
● Ladder
● Safety Goggles
● Wire Cutter
● Wire Stripper
● Level
Note : Safely dispose of packaging materials. Assistance will be required to support fixture during installation.
DIMMABLE FUNCTIONALITY
This fixture is dimmable with most regular dimmers. Following dimmers tested to be compatible with this fixture, dimming range up to: 10%-100%. If you are unfamiliar with electrical installations, it is recommended you have a qualified electrician do your installation.
SECTION A: PREPARING FOR INSTALLATION
-
Mounting Location
– Plan the layout of the fixtures and ensure power wiring is routed to all installation locations.
– A 3″ or 4″ junction box must be installed at each desired location before installing the fixture.
Junction Box (Not included)
· 3″ & 4″ square or octagon shaped junction box.
· Depth of J-box: at least 1/2″ deep. -
Disconnect Power
– Place the wall switch to the “OFF” position. ( Fig.1. )
– Depending on which type of fuse box you have in your home:
Fig.2. Place either the main (Master) switch to the “OFF” position, cutting off power to your entire home OR turn off the individual switch that provides power to where the fixture will be installed
OR
Fig.3. Place either the main (Msster) switch to the “OFF” position, cutting off power to your entire home OR turn off the fuse that provides power to where the fixture will be installed
– Carefully unpack the fixture. Lay out all parts on a clean surface.
– Remove the old fixture.
SECTION B: MOUNTING INSTALLATION
1. Disassemble the fixture
- Twist counterclockwise to loosen the canopy screws (bb).
- Remove the mounting bracket (C) from fixture (A). Do not remove any other parts.
Note : To avoid damaging this product, place the components on a soft, non-abrasive surface such as carpet or cardboard.
2. Install the hardware
- Orient the mounting bracket (C) so that the arms are facing away from the junction box (not included), pull the power supply wires from junction box through the center opening of the mounting bracket.
- Use either the existing junction box screws or the mounting screws (aa) to attach the mounting bracket flush to the junction box, make sure the mounting bracket is level before fully tightening the mounting screws (aa).
Note : The elongated slots in the mounting bracket may be utilized to achieve the correct orientation for horizontal or vertical installation.
Note : The illustrated junction box is 4-inch, keyhole slots location may be different on a 3-inch Junction box.
3. Connect the wires
– Strip 3/8″ of bare power supply wires from the junction box.
Note : Assistance will be required to support the fixture during installation.
– Follow the wires connection guide to connect the wires from fixture (A) to the power supply wires from the junction box using the wire nut (cc).
Note : Ensure that no bare wires are exposed after making the connections.
– Connect the yellow/green ground wire from the fixture (A) to the bare copper ground wire from the junction box using a wire nut (cc). (If house wiring does not include a ground wire, consult your local electrical code for approved grounding methods).
– Ensure the connectors are spliced tightly and carefully push the spliced wires back into the junction box.
WIRES CONNECTION GUIDE
Ground Wire :
- For safety and proper operation, the fixture must be properly grounded.
- A green or bare copper ground wire is pre-attached to the fixture. The fixture yellow/ground wire must be spliced to the green or bare copper ground wire in the junction box using one of the wire nuts (bb).
Power Supply Wires :
- Connect the NEUTRAL supply wire (White) from the junction box to the NEUTRAL fixture wire (White)
- Connect the HOT supply wire (Black) from the junction box to the HOT fixture wire (Black)
4. Install the fixture
- Position the fixture (A) over the junction box, pass canopy (B) over the arms protruding from mounting bracket (C) , engage the fixture with the mounting bracket.
- Secure the canopy and mounting bracket with canopy screws (bb).
Note : Assistance will be required to support the fixture during installation.
5. Rotate the fixture to the desired angle
- Rotate the fixture to the desired angle for directional light control.
- Turn on power at circuit breaker or fuse box.
- Turn the light switch on to activate the fixture.
SECTION C: TROUBLESHOOTING
Questions, problems, missing parts? Before returning to the store, contact
Inlight Customer Service
info@getinlight.com
Retain this manual for future use.
is registered trademarks of Inlight Co. Ltd. All Rights Reserved.
V. 2019
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>