FOVAL Wireless Car Charging Holder User Manual
- June 7, 2024
- FOVAL
Table of Contents
FOVAL Wireless Car Charging Holder
What is included
Wireless holder X 1
Charger holder X 1
USB cable X 1
Features
- Car holder with wireless charging function, charges your phone conveniently when driving
- Designed to provide wireless-charging phones with output 5W/7.5W/10W
- Full 360 degrees rotation for perfect viewing angle
- Adjustable foot support makes easy to align to the charging center
- Start charging asap as the phone contact with the holder, no need cable anymore
- QC 3.0 USB car charger included so you can start charging readily, with over temperature, over current, over voltage multi-safety protection
Compatible devices
- Work well with iP XS Max / NOTE 8 / 9 / iP XR / 8P / iP XS / iP X / S8 / S9 / iP 8
- Also work with all other Qi enabled devices
Parameters
Wireless holder
Grip nut
Fix the charger & holder
Charger holder
Fix the wireless charger to your car air vent clip
USB cable
Connect wireless charger & car charger, power the wireless charger
Product specification
Wireless holder
Input voltage| DC 5V/9V| Input current| 2A
Output power| 5W/7.5/10W| Frequency| 11 0-205KHZ
LED mode
| Working state | LED light color |
|---|---|
| Power transfer | Red, blue, red blue light turn on by turns for once, then off |
| Standby mode | Light off |
| Charging | Red light keeps on |
| FOO Warning | Red light keeps flashing |
| Charge complete | Red light keeps on |
Installation
-
Fix the mount, charger & Nut
-
Insert the mount directly into the car air vent blade
-
Press down the locking switch to secure the car air vent clip
-
Intervene USB cable with your car charger
Note: connect to power QI charger can speed up charging speed
-
According to the height of your phone, pull out the bottom bracket of the phone so that the wireless charging coil is aligned with the mobile phone.
Note: If the coil is not aligned with the mobile phone, it will not charge you phone
-
Press the back button to open the wireless charging clamp, put the mobile phone into the wireless car charging, tighten the clip, and the phone starts to charge (the indicator is red).
-
Press the back button and take the phone out
Attentions
- Please use the product correctly according instructions
- Please do not disassemble the product or throw it to fire and water, to avoid leakage caused by electrical short circuit
- Please do not use wireless charger in high temperature, wet, corrosive environment, to avoid leakage from caused by damaged circuit
- Please do not put wireless charger close to cards with magnetic stripes or chips (ID card, credit card etc.) to avoid demagnetization
- Please keep wireless charger at least 20 CM distance away from implantable medical device (heart pacemaker, Implantable cochlea etc.) to avoid potential interferences
- Please do safekeeping, do not let your kids treat wireless charger as toy to avoid unwanted accidents
The pictures only supplies the reference, please take the actual product as the standard
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
If you have any questions about our product and service, please do contact
us via the email below:
[email protected]
Documents / Resources
|
FOVAL Wireless Car Charging
Holder
[pdf] User Manual
Wireless Car Charging Holder
---|---