VWA H2CAP hydrogen water generator User Manual
- June 7, 2024
- VWA
Table of Contents
**User Manual
**
- Videos can be found at www.h2cap.com
- For more information about the H2CAP, check out our Q&A at our website.
What is H2CAP?
- The H2CAP is a hydrogen water generator that comes in a compact size for the best portability. All you need with the H2CAP is a USB cable and a 500 bottle.
- By making use of the Platinum titanium electrode and platinum PEM membrane, the H2CAP is free of residual chlorine and ozone. Plus, these allow the H2CAP to produce hydrogen water with,000ppb ~00ppb that can last longer.
- For the users to test its performance, the H2CAP package comes with a test kit that can measure the DH of the hydrogen water.
- For user convenience, additional accessories such as the Descaler and test reagent are available for sale.
The H2CAP was certified by Japan Hydrogen Water Promotion Association to produce hydrogen water with more than 1,000ppb <Test report number – 218H-221>
Product Composition
Product components may vary depending on the package type.
Accessories ……………………………………
Parts of the H2CAP
- Upper Cap
- Case
- USB Port
- Bottom Cap
- Membrane
- Electrode Plate
- Sealing O-ring
- Warranty Seal Sticker
LED light Indication
| LED | Indication |
|---|---|
| White LED On | Producing hydrogen Water |
| White LED Blinking | Ongoing Cleaning mode |
| Orange LED On | Hydrogen water produced or cleaning completed |
| Orange LED Blinking | Hydrogen water produced & cleaning is required |
| A quick blink of Orange LED | System Error |
Usage Precautions
Read the following precautions before using the product.
-Use drinkable water only. Other beverages such as coffee, beer, and etc. may damage the product.
-To prevent the electrode plate from drying out, store the H2CAP with the upper cap closed.
-Do not use the H2CAP when the USB port or the cable is wet.
-Do not disassemble or modify the product. Free warranties are not available once the seal sticker is damaged.
-Do not attach the H2CAP too tightly to the bottle.
-Be careful not to damage the electrode plate and the membrane.
Once they are damaged, leakage may occur and free warranties will not be
available.
-Use bottles that are compatible with the H2CAP (28mm, 30mm).
-Using without any water may damage the product. Clean promptly when notified with the cleaning alarm to maintain the best performance.
-Do not consume the Descaler or the reagent.
-Use water temperature lower than 50
-Do not disassemble the bottom cap when not necessary.
How to Operate the H2CAP
Before First Use
-For supplying power, H2CAP is compatible with a variety of devices.
To supply power to H2CAP with smartphones, OTG gender is required. (Supplying
power via iPhone is unsupported.)
-Make sure to remove the white plastic plug at the center of the bottom cap.
-H2CAP comes with a small amount of water on the electrode plate to keep the product moisturized.
-Run the cleaning mode before using the product for the first time. (Check 5-2. to learn the detailed cleaning mode)
-A Noise of hydrogen gas evaporation may occur upon opening the cap after producing hydrogen.
How to Run the Cleaning Mode
- Cleaning alarm: The H2CAP automatically alarms you when to do the cleaning mode.
- Insert one sachet of Descaler with 100 of clean water and shake the bottle until the Descaler is dissolved into the water. Then, turn the bottle upside down.
- Connect the USB cable and unplug it when the white LED goes off after 3 seconds. Then, reconnect. The cleaning mode will start automatically and turn off after 2mins.
- Once the cleaning mode is completed, dispose of the water and rinse 2 to 3 times with clean water.
Use only the Descaler provided. (One sachet at one time)
Using other cleaning tools may damage the product.
Do not submerge the product in the water for cleaning purposes.
You may refer to our videos at www.h2cap.com for
guidelines.
How to Produce Hydrogen Water
-
With water fully filled, attach the H2CAP to the bottle.
Then, turn upside down as shown in the image. -
When the USB cable is connected, the H2CAP will start automatically to produce hydrogen water.
-
The production of hydrogen water may take 3mins 30sec up to 5mins depending on the condition of the water.
(Refer to the specification for details) -
Once completed, the orange LED will turn on.
If left not opened for a long time after the hydrogen water production,
hydrogen gas pressure may cause small drops of water to come out from the
bottom cap.
Running this model 2 times will produce hydrogen water reaching up to
1,500ppb.
Using alkaline water or mineral water will produce
hydrogen water reaching up to 1,500ppb.
You may refer to our videos at www.h2cap.com for
guidelines.
How to Do the Dissolved Hydrogen(DH) Test
- Do the test with a water temperature of 25~35 Shake the reagent well enough before starting the test.
- Pour the hydrogen water to be tested until the indicated line (6cc) of the provided test bottle.
- Make 7 drops of reagent to the bottle.
- If the reagent drops turn transparent, start adding 1 drop at a time.
- The water contains 1,000ppb ~ 1,100ppb of hydrogen if they turn blue on the 11th drop.
One drop equals 100ppb.
Slightly shake the test bottle every time the reagent is dropped.
DH test results may vary depending on the environment.
Use the hydrogen meter for exact results.
For more exact results, do the test after running the cleaning mode.
Do not reuse the reagent once opened.
You may refer to our videos at www.h2cap.com for
guidelines.
