Thermador Double Drawer Refrigerator Installation Guide
- June 7, 2024
- Thermador
Table of Contents
INSTALLATION GUIDE
Model/Modele/Modelo
T24UR925DS
T24UR915DS
T24UR905DP
Double Drawer Refrigerator
IMPORTANT : Before you begin, read these instructions completely and
carefully.
INSTALLER : Please leave this manual with the owner for future reference.
OWNER : Save these installation instructions for local electrical
inspector’s use and for future reference.
Important Safety Instructions
READ AND SAVE THESE INSTRUCTIONS!
These installation instructions are intended for use by qualified installers.
In addition to these instructions, the appliance shall be installed:
- In the United States, in accordance with the National Electric Code/State and municipal codes and/or local codes.
- In Canada, in accordance with the Canadian Electric Code C22.1 –latest edition/Provincial and Municipal codes and/or local codes.
Be sure to observe all listed warnings and cautions. Look for the triangles
with exclamation marks inside.
WARNING: This indicates that
death or serious injury may result due to the non-observance of this warning.
CAUTION : This indicates that
minor or moderately severe injury may result due to the non-observance of this
warning.
NOTE : This is used to draw the user’s attention to something in
particular.
State of California Proposition 65 Warnings:
WARNING
This product can expose you to chemicals including vinyl chloride, which is
known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to
www.P65Warnings.ca.gov.
Important
- NEW INSTALLATION – If the appliance is a new installation, most of the work must be done before the unit is moved into place.
- REPLACEMENT – If the appliance is replacing another appliance, the connections for the appliance being replaced must be checked for compatibility with the new unit and replaced as necessary.
Inspect the Refrigerator
Remove all tape, packaging, and plastic covers. After unpacking the appliance
and prior to installation, thoroughly inspect the Refrigerator for possible
freight or cosmetic damage. Report any damage immediately.
NOTE : Please do not discard any bags or items that come with the
original package until after the entire installation has been completed!
Tools needed for installation
These are the
tools that you may need for the installation of the appliance. However, if you
need to modify the counter or cabinetry to fit the unit, you may need other
tools to make counter/cabinetry modifications before installing the appliance.
Materials supplied
Anti-tip-bracket. 2 pieces. Screws: 2 pieces. 1 Insulating Foam (Not illustrated) 20 1/2” (520mm) x 29 1/8” (740mm) x 1/8” (3mm)
KIT ALSO INCLUDES ONLY FOR T24UR905DP MODELS: Wood Screws:8 pieces Overlay support: 8 pieces
Installing the appliance
Most of the installation work must be done before the Refrigerator is moved into place. Have a Qualified technician install and connect the appliance according to the enclosed installation instructions.
WARNING:
Do not install this appliance:
– Outdoors
– In an environment with dripping water
– In rooms where there is a risk of frost
Transporting
The appliance is heavy and must be handled with caution during transportation
and installation. Because of the weight and dimensions of the appliance, at
least two persons are necessary to move the appliance into position securely
and avoid injuries to people or damage to the appliance.
General measures
Note : With the legs fully retracted the appliance has a minimum dimension of 34 1/8” from top to bottom. The legs can be extended up to 1/2” (13mm).
Installation location
A dry, well-ventilated room is suitable as an installation location. The installation location should not be exposed to direct sunlight and not placed near a heat source, e.g. a cooker, radiator, etc. If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following minimum distance from the heat source:
- To electric or gas oven/range 1¼” (3 cm).
- To an oil or coal-fired cooker 1113/16” (30cm).
- To another Refrigerator or Wine Reserve 1” (2.54cm).
The floor of the installation location must not give way; if necessary,
reinforce floor. The appliance must be upright and level to function
correctly.
For proper operation and appearance of the unit, the cabinet opening should be
square and have dimensions as shown in the next diagrams.
Top View
Thermador double drawer under counter top dimension. (Unit door flushed with
the cutout)
Measurements in inches (mm)
Frontal view
measurements in inches (mm)
Installing Side-by-Side
The appliance can be installed beside another Thermador appliance. Follow the
next dimensions and notes for the correct installation of the appliance in a
side-by-side layout.
NOTE: Before placing the unit into the niche, adhere the Insulating Foam
(included with the product) on
the side of the unit that will be placed next to the additional appliance. Be
sure that the Insulating Foam ieven with the surface of the unit and that
there are no bubbles or bumps on the Insulation Foam after adhering it to the
unit.
Two Double Drawer Refrigerators are side-by-side.
One Double Drawer and one swing door appliance : opening of the door should be opposite to the Double Drawer to avoid interference or damage by hitting.
-Do not place a swing door appliance with the opening of the door right beside the Double Drawer.
The drawers and the door may impact each other damaging the units.
Ventilation
The Refrigerator unit is ventilated only at the Toe-Kick in the base. Never cover that area or place anything in front of it. Otherwise, the refrigeration cooling performance will be affected, and the unit must work harder to increase power consumption.
Connecting the appliance
After installing the appliance, wait at least 1 hour to turn on the appliance.
During transportation, the oil in the compressor may have flowed into the
refrigeration system.
Before switching ON the appliance for the first time, clean the interior of
the appliance (see chapter “ Cleaning the appliance ” in the Use & Care
Guide).
Electrical connection
WARNING:
These installation instructions are intended for use by qualified installers.
WARNING:
Avoid the risk of an electric shock!
Insert into a grounded receptacle.
Never remove the grounding phase.
Do not use any adapters.
Do not use any extension cords.
WARNING:
It is the customer’s responsibility to ensure that the appliance installation
is in compliance with all national and local electrical codes and ordinances.
Non-compliance with these instructions may result in death, fire or an
electric shock.
The receptacle must be near the appliance, 61” (1550mm) to the right of the
appliance or 37” (940mm) to the left of the appliance, and also freely
accessible following installation of the appliance for future service.
The appliance complies with protection class I. Connect the appliance to 115
V/ 60Hz alternating current via a correctly installed receptacle with the
grounded terminal.
The appliance comes with a UL registered 3-wire power cord NEMA 5-15p type.
The appliance requires a 3-pole receptacle.
WARNING:
Never connect the appliance to electronic energy saver plugs. This appliance
can be used with mains and sine-controlled inverters. Main controlled
inverters are used for photovoltaic systems which are connected directly to
the national grid. Sine-controlled inverters must be used for isolated
applications (e.g. on ships or in mountain lodges) which are not connected
directly to the national grid.
The appliance requires a 3-pole socket. The socket should be connected by a
qualified electrician only. Where there is a 2-pole standard wall socket, it
is the responsibility of the customer to have this socket replaced with a
correctly grounded 3-pole wall socket. Do not use any adapter plugs. Be sure
that the location of your refrigerator has a near and accessible electric
socket.
It is recommended that a separate circuit serving only your wine cellar be
provided. Use an outlet that cannot be turned off by a switch. Do not use an
extension cord.
2-pole standard wall socket must be replaced with a 3-pole grounded socket. Do
not use adapters.
Installing the anti-tip-brackets
The appliance includes two anti-tip brackets. If your cabinetry is not designed for the specific dimensions of your appliance, or if you plan to use the appliance as a free-standing unit, you should use these brackets to avoid your appliance tilting due to unbalanced overweight situations where both drawers are opened at the same time.
WARNING:
To avoid the appliance tilting due to unbalanced overweight do not open both
drawers at the same time. Always close one drawer before pull out another.
For free-standing use
- Consider the distance necessary for the appliance to be flush with the front of your cabinetry. If there is no cabinetry, put the unit close to the wall, then take the measurement of the space at the back, between the unit and the wall.
- Based on the measured distance between the back of the unit and the wall, bend the anti-tip bracket (included with the unit) from the pointed lines to form a “step” with the same Distance measured.
Resultant formed “step”.
NOTE : The adhesive foam must be at the bottom of the step, never on the
reverse side.
3. Peel the adhesive foam and paste the anti-tip bracket at both sides on the
back of the appliance as shown in the illustrations.
4. With the anti-tip brackets pasted on the back of the appliance, slide the
appliance to the wall until the anti-tip bracket is touching the wall.
Using the screws provided, fasten the anti-tip bracket to the wall for both
sides.
NOTE : Do not fasten the unit to drywall. Be sure to attach the unit to a
solid surface.
For under-counter use
1. Consider the distance necessary for the appliance to be flush with the
front of your cabinetry.
2. Take the measurement from the top of the cabinet of the unit to the bottom
of the counter. The measurement X”(mm) may vary depending on the design of the
counter, an extension of the legs of the product, etc.
3. Based on the Distance = X” (mm) between the appliance and the counter, bend the anti-tip- brackets included with the appliance on the pointed lines to form a “step” 1/16” (2mm) smaller than the Distance = X” (mm) measured.
4. Peel the adhesive foam and paste the anti-tip-bracket at the front on the top of the cabinet of the appliance, near the corners as shown in the picture:
5. Slide the appliance into the cabinet until the front of the appliance is flush with the front of the cabinetry. Check that nothing interferes or obstructs the anti-tip bracket while sliding under the counter.
Installing the overlay panel
(For T24UR905DP models only)
If you plan to install a custom overlay panel, you will need to create the
panel yourself or consult a qualified cabinetmaker or carpenter.
A full-sized template for easier marking the hole pattern is included in the
manual package.
IMPORTANT:
– The thickness of both the overlay panels must be ¾” (19mm).
– Overlay panel must not weigh more than 10lbs (4.54kg) each.
– Overlay panels weighing more than recommended may cause damage to your
appliance.
– It is recommended to have the help of a second person to install the panel.
– Use the recommended tools in the installation manual to facilitate the
installation of the panel. Failure to use the recommended tools or the help of
a second person may result in damage to panel and/or the appliance.
– To install the panel, use only the screws included in the “Installation
Kit”. Create the custom overlay panel using the dimensions shown.
Top Panel:
Bottom drawer:
1. Install the custom handle of your preference on the overlay panel before
installing the panel on the drawer.
– Every custom handle is different, and it is the responsibility of the
customer to make the necessary adjustments to place the handle on the overlay
panel.
– The screws used to affix the custom handle to the panel must be flat and
flush with the surface of the panel (Fig A); if the screws are not flat, then
consider making a recession on the overlay, enough to hide the head of the
screw below the surface of the overlay, otherwise the screws will interfere
with the correct placement of the overlay on the drawer (Fig B).
2. Remove the gasket from the top corners of the door pulling it gently.
Under the gasket in each corner, there is a recess with a guide to
breakthrough to use as screw positions for the panel. It is not necessary to
remove all the gasket, only a portion enough to make the recess accessible.
After the gasket is moved break through the guides, make sure not to damage
the gasket.
Using the screws and supports included in the “installation kit”, position
the support in the recess and secure the overlay panel screwing it from the
inside of the drawer through the same hole left by the removed screw until the
panel is firmly attached to the drawer.
Break trough the marked area in each corner and use the (1) Overlay Support and (2) Screw to secure the overlay Panel
3. After securing the overlay to the drawer, put the gasket back in its place
pressing it against its channel on the drawer until all the gasket is even and
back in place.
Repeat the same steps for the other drawer.
Now, the overlay panels are ready.
Customer Service Information
If service becomes necessary, contact your dealer or an authorized service center. Do not attempt to repair the appliance yourself. Any work performed by unauthorized personnel may void the warranty. If the problem persists, take the following steps (in the order listed below) until the problem is corrected to your satisfaction.
-
Contact your dealer or the Thermador Authorized Servicer in your area.
-
E-mail us from the Customer Service section of our website, www.Thermador.com.
-
Write to us at the address below:
BSH Home Appliances Corporation
1901 Main Street, Suite 600
Irvine, CA 92614 -
Call us at: 1-800-735-4328
Please be sure to include (if writing), or have available (if calling), the following information:
- Model Number
- Serial Number
- Date of Original Purchase
- Date Problem Originated
- Explanation of Problem
Also, if writing, please be sure to include a daytime phone number. (You will find the model number and serial number information on the label located at the right side of the bottom compartment.).
Data Rating Label
The data rating label shows the model and the serial number of your appliance.
It is located at the right side of the bottom compartment.
Service Information
For handy reference, copy the information in the form below from the data
rating plate located at the right side of the bottom compartment. Keep your
invoice for Warranty validation.
PN: ARAH1E1050500 / 8001087776
04/2021
T24UR925DS
T24UR915DS
T24UR905DS
Printed in Mexico
lmpreso en Mexico
lmprime au Mexique
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>