HOOVER Combined and Frost Free Combined Instruction Manual
- June 6, 2024
- Hoover
Table of Contents
COMBINED AND FROST-FREE COMBINED
CONTROL PANEL
The thermostat box to control the appliance is located inside the fridge
compartment on the top right. To check whether the appliance is functioning,
make sure that the thermostat knob is not set on “0”. Adjust the knob
according to the desired temperature in the fridge.
In this product, the freezer compartment is automatically defrosted. A small
amount of frost or drops of water on the back of the fridge compartment when
the fridge is working is normal.
Make sure the water outlet is always clean. Make sure foods do not touch the
back or sides of the fridge compartment
Important: If the room temperature is very warm, the appliance may work
continuously and a layer of frost will deposit on the back of the fridge
compartment. In this case, turn the knob to lower settings.
FREEZING OF THE FREEZER COMPARTMENT
Place the foods to be frozen in the drawer. At the start of the freezing process, so as not to make the fridge compartment excessively cold, it may be necessary to turn the thermostat knob back, according to the load and room temperature. Once the freezing process is completed, return the thermostat knob to the usual value. The rating plate states the maximum quantity of foods that can be frozen, (see figure 2).
DEFROSTING OF THE FREEZER COMPARTMENT
In the case of a fridge with FROST FREE technology, the freezer compartment
does not need to be defrosted because this product is equipped with an
automatic system that prevents ice from forming;
In case of a version without FROST FREE technology, it is recommended to
manually defrost the product when the layer of frost is more than 3 mm thick,
by setting the knob on “0”. Open the door and remove the foodstuffs, making
sure to store them in a cool place. Leave the door open as long as is
necessary for the layer of frost to melt. Dry the inside of the freezer with a
sponge/cloth. Reposition the foodstuffs and reset the knob to the usual
values.
N.B.: This is the rating plate. If you need to contact our Service
Department in the event of faults, remember to give them the information on
the plate.
N.B.: For better air circulation, leave some room between the foodstuffs.
In the case of models with FROST FREE technology, avoid obstructing the
cooling air vents.
N.B.: To TEST consumption and preservation standards, remove all drawers
except for the bottom one.
REVERSING THE OPENING OF THE DOORS
Place the appliance on the floor or at a 45° angle, since it is necessary to work on the bottom of the appliance.
Remove the bottom hinge by loosening the screws, then remove the lower
door.
|
Remove the middle hinge by loosening the screws, then remove the top
door.
---|---
Remove the bushes on the right-hand side of the doors and mount them back on
the left-hand side.
|
Remove the top hinge by loosening the screws. Unscrew the pin from the
hinge.
Disassemble and move the corner guide from the left to the right-hand side,
turning it 180°.
|
Remount the hinges and doors working from bottom to top, 1 – 2 – 3. Also,
remount the spacer washers between the door and hinge.
While fixing the top hinge on the left-hand side, tighten the screws and screw
the pin back on in the left hole.
|
In order to reverse the vertical handles, if any, remove the outer caps from
the righthand side of the doors.
Unscrew the handles from the left-hand side and move them to the right-hand
side, then position the outer caps removed previously from the right-hand side
to the left-hand side.
Put the appliance back in an upright position and wait two hours before
turning it on.
N.B. For the doors to be correctly aligned, it is necessary to operate on
the middle hinge.
Z STUDIO > 07-2009
Cod. 41032400
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>