Dell S2721HSX Monitor Teardown Instructions

June 6, 2024
Dell

S2721HS/HSX

Disassembly Procedures:

S1  Open the Pizza carton with a proper tool.

Dell S2721HSX Monitor Teardown S2 Take out all of the accessories including QSG, HDMI cable, power cable, CD&user’s manual, stand base, stand riser, and EEI label from the carton. (Note: It depends on whether users returning the accessories)

Dell S2721HSX Monitor Teardown-

S3Take out of the molded pulp with base carton, then take out the riser and monitor from the EPE bag and put it on a  protective cushion.

Dell S2721HSX Monitor Teardown-1

S4Use a Philips-head screwdriver to remove 4pcs screws for unlocking mechanisms.
(No.1~4 screw size=M4x11; Torque=7 8kgfxcm)
Dell S2721HSX Monitor Teardown-2S5Wedge your fingers between the rear cover and the middle bezel on the corners of the top side of the monitor to release the rear cover, then use one hand to press the middle bezel, the other hand to pull up carefully the rear cover in order of arrow preference for unlocking mechanisms of rear cover.Dell S2721HSX
Monitor Teardown-3

`S6```Tear off 1pcs acetate tape and then disconnect the panel lamp cable away from the connector of the panel. Tear off 2pcs aluminum foils, and then disconnect the function key cable away from the connector of the board.Dell
S2721HSX Monitor Teardown-4Dell S2721HSX Monitor
Teardown-5

S7Use a Philips-head screwdriver to remove 18pcs screws for unlocking the middle bezel.
(No.1~13 screw size=M3x4, Torque=3~4kgfxcm;
No.14~18 screw size=M2x3.3, Torque=1±0.2kgfxcm)

Dell S2721HSX Monitor Teardown-6

S8Use a Philips-head screwdriver to remove 2pcs screws for unlocking the bracket with the panel module.
(No.1~2 screw size=M3x3, Torque=3~4kgfxcm )Dell S2721HSX Monitor
Teardown-7

S9Take away the middle bezel, and put it on a fixture.
U se a Philips-head screwdriver to remove 3pcs tear off the tapes for releasing the key cables.
screws for unlocking the function key board, and then
(No.1~3 screw size=M2x2.4, Torque=0.8±0.2kgfxcmDell S2721HSX Monitor
Teardown-8Dell S2721HSX Monitor
Teardown-9

S10Tear off the tape, then lift up the panel module with the bracket chassis for releasing the front bezel away from the panel module.Dell S2721HSX
Monitor Teardown-10

S11Unplug the LVDS cable from the connector of the panel module by pushing the earing locks.Dell S2721HSX Monitor Teardown-11S12Take away the bracket chassis module and then put the bracket chassis module on a protective cushion.Dell S2721HSX Monitor Teardown-12

S13Remove the Mylar from the hooks of the bracket chassis module.Dell
S2721HSX Monitor Teardown-13

S14Use a Philips-head screwdriver to remove 5pcs screws for unlocking the circuit board, release all the cables from the hooks.
(No.1 screw size=M4x8, Torque=6±0.5kgfxcm;
No. 2~5 screw size=M3x7.5, Torque=6±0.5kgfxcm)Dell S2721HSX Monitor
Teardown-14Dell S2721HSX Monitor
Teardown-15

S15Remove the interface board and power board from the bracket chassis module carefully, and disconnect all the cables.Dell S2721HSX Monitor
Teardown-16

S16Remove electrolyte capacitors (red mark) from printed circuit boards.Dell S2721HSX Monitor Teardown-17

S16-1 Cut the glue between bulk cap. and PCB with a knife.Dell S2721HSX
Monitor Teardown-18S16-2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB.Dell S2721HSX Monitor
Teardown-19S16-3 Cut into the bottom of the bulk cap. and pull it up carefully.

Dell S2721HSX Monitor Teardown-20S16-4 Take out the bulk cap. pin solder with soldering iron and absorber.Dell S2721HSX
Monitor Teardown-21S16-5 Lift the bulk cap. up and away from the PCB.Dell S2721HSX Monitor Teardown-22

Product material information
The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.

Capacitors / condensers (containing PCB/PCT) No used
Mercury-containing components No used
Batteries No used
Printed circuit boards (with a surface greater than 10 square cm) The product

has printed circuit boards (with a surface greater than 10 square cm)
The component contains toner, ink, and liquids| No used
Plastic containing BFR| No used
Component and waste contain asbestos| No used
CRT| No used
Component contain CFC, HCFC, HFC and HC| No used
Gas discharge lamps| No used
LCD display > 100 cm2| The product has an LCD greater than 100 cm2
External electric cable| The product has external cables
The component contains refractory ceramic fibers| No used
The component contains radioactive substances| No used
Electrolyte capacitors (height > 25mm, diameter > 25mm)| Product has electrolyte capacitors (height > 25mm, diameter > 25mm)

Tools Required

List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed.
Tool Description:
– Screwdriver (Phillip’s head) #1
– Screwdriver (Phillip’s head) #2
– Penknife
– Soldering iron and absorber

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals