Kmart 42835868 3-In-1 Tri Scooter Instructions
- June 6, 2024
- Kmart
Table of Contents
3 IN 1 TRI SCOOTER INSTRUCTIONS
Keycode: 42835868
WARNING! Assembly by an adult.
Not suitable for children younger than 18 months old, due to the danger of
falling. Protective equipment should be worn. Not suitable for children with a
body mass of more than 20 kg. Do not use on public roads.
Remove the scooter and all the parts from the box. Set out all the parts and
read the assembly instructions prior to use. Keep the packaging until assembly
is complete.
General instructions
- This scooter must be assembled by a responsible adult. Prior to use, make sure that the scooter has been assembled properly. Remove all the parts which are not necessary for play before giving the scooter to your child. Due to the skill it requires, the scooter must be used with care in order to avoid falls or collisions likely to injure the user or others.
- To be used with suitable protective equipment, including a helmet, shoes, elbow, wrist, and knee protection. Teach the child how to use it safely and responsibly.
- The scooter is not a toy for children under the age of 18 months.
Directions
a) The scooter can be dangerous and can lead to traffic accidents when used on
public highways. Do not use on public roads.
b) For use on smooth, paved surfaces only.
c) Avoid bumps and drainage grates that may cause an accident.
d) The scooter does not include any headlights or lights. It is therefore not
suitable for use at night or during periods when visibility is limited.
e) Always use under adult supervision.
f) Do not allow more than one child to ride the scooter at the same time.
Before and after use
– Check the height of the steering system, and make sure the spring button is
secured.
– Check all of the connection elements: the brake, the quick release system of
the steering column, and the wheel axles are adjusted correctly and not
damaged.
– Also check the wheel’s wear.
During use
– Hold both handgrips firmly. Put one foot towards the front of the deck. With
the other foot, push off the ground to propel the scooter forward. Both feet
can fit on the deck when the desired speed has been reached. To stop, step on
the brake with the rear foot.
– Braking: a brake is located at the rear, when necessary, press down on it to
slow down. Press down gradually in order to prevent skidding or loss of
stability. The brake may heat up after multiple uses. Avoid touching it during
and after use.
– Shoes are mandatory and we strongly advise you to wear pants and long sleeve
shirts to avoid injury if you fall.
– Children should be reminded that the scooter should be used with caution,
since it requires skill, so as to avoid falls or collisions causing injury to
the user and others.
Assembly Instructions:
-
ASSEMBLE THE HANDLEBAR
Step 1: Press the spring button on the bottom of the handlebar.
Step 2: Push the handlebar into the footplate.
Step 3: Make sure the spring button pops out to secure in position properly as indicated. -
INTERCHANGE THE HANDLEBAR
Step 1: Press the spring button on the bottom of the handle bar.
Step 2:Pull out the handle bar from the footplate.
Step 3: Follow the above assembly instruction to interchange other handlebars.
-
ADJUST THE STEM
To adjust the stem, release the quick lock and press the spring button, then adjust the handlebar to one of the 3 height levels. The button must then pop into the fixation hole. Tighten the quick lock to secure the handlebar. After use, simply loosen the quick-lock, press the spring button, and push down the handlebar. Tighten the quick lock to secure the handlebar.
Care Instructions
A . Wheel bearings: Avoid going through water, oil, or sand as this can
damage the wheel bearings.
To look after the wheel bearings, systematically check that the wheels turn
properly by turning the scooter upside-down and using your hand to spin the
wheels. If the wheels do not spin they must then be removed to check their
condition. First, unscrew the wheel axle, remove the axle and detach the
wheel, then carefully push the two-wheel bearings out of their housing. If
they are chipped or dented, they should be replaced. If there is no visible
damage, they must then be oiled. To do this, remove all traces of grease, mud,
or dust with a kitchen towel or cloth, and re-oil them with a grease spray or
by leaving them to soak overnight in oil [turn them several times in the oil
first]. Reassemble the wheel bearings and axles, followed by the wheel, onto
the scooter. Repeat the process for the other wheel.
B . Wheels: The wheels wear down with time and can be pierced if overly
used on rough surfaces. The back wheel on which the brake is applied is
particularly affected after several hours of braking. In the interest of
safety, they should be checked regularly and changed if necessary.
C . Modifications: The original scooter must by no means be modified
except for the maintenance-related changes mentioned in these instructions.
D. Nuts and axles: These should be checked regularly. They can become
loose after a while in which case they should be tightened. They can become
worn and not tightened properly, in which case they should be replaced.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>