DELL E1715S 17-Inch 5:4 LED-Backlit TN LCD Monitor User Guide
- June 6, 2024
- Dell
Table of Contents
| Step | Figure | Remark |
|---|---|---|
| S1. Remove the STAND BASE ASS’Y. | | Turn off power,
Unplug external cables from product
S1. Remove the STAND BASE ASS’Y.| 
| Note: Put the
monitor on a flat, soft and clean surface. Press the button on the red circle
then pull out the stand follow the arrow, stand-base assy will be remove.
S2. Remove the REAR COVER.| 
| Use a Philips-
head screwdriver to remove 6 screws for unlocking mechanisms.
(No.1~2 screw size=M4x10; Torque=12±2kgf.cmNo.5~6 screw size=P3x4;
Torque=6±1kgf.cm)
S2. Remove the REAR COVER.| 
| Use Penknife to
separate the bezel and rear cove follow the arrows in sequence, then you can
take out rear cover.
S3. Remove the Cable.| 
| Disconnect the keyboard harness.
S4. Disconnect the LED
HARNESS and FFC CABLE.| 
|
S5. Remove the MAIN and POWER
BOARD.| 
| 1. Turn over the main frame.
2. Remove the Insulatingsheet. Use a Philips-head screwdriver to removescrews
for unlocking Mainboard and Power board (No.1~3 screw size=M3x6;
Torque=6±1kgf.cm No.4 screw size=M4x6; Torque=6±1kgf.cm）
Use a Philips-head screwdriver to remove 1 screws for unlocking Main board
（No.1 screw size=M3x5; Torque=6±1kgf.cm）Use a hex screwdriver to remove 2
screws for unlocking mainboard
（No.2~3 Hex screw Torque= 4.5 ±0.5kgf.cm）
S6. Disconnect the HARNESS.|
|
S7. Remove the MAIN FRAME|
|
S8. Remove the PANELfrom Bezel|
|
S9. Remove
the KEY
BOARD.| 
| Use a Philips-head screwdriver to remove 4 screws for unlocking Key board
(No.1~4 screw size=M2x2.5; Torque=0.7±0.2kgf.cm)
S10.Remove capacitors| 
| Remove
electrolyte capacitors (red mark) from printed circuit boards
S10.Remove capacitors|
| Take out the bulk cap. pin solder with soldering iron and absorber
| 
| Lift the bulk cap. up and away
from the PCB
2. Product material information
The following substances, preparations, or components should be disposed of or
recovered separately from other WEEE in compliance with Article 4 of EU
Council Directive 75/442/EEC.
| Capacitors / condensers (containing PCB/PCT) | No used |
|---|---|
| Mercury-containing components | No used |
| Batteries | No used |
| Printed circuit boards (with a surface greater than 10 square cm) | The product |
has printed circuit boards (with a surface greater than 10 square cm)
The component contains toner, ink, and liquids| No used
Plastic containing BFR| No used
Component and waste contain asbestos| No used
CRT| No used
Component contain CFC, HCFC, HFC and HC| No used
Gas discharge lamps| No used
LCD display > 100 cm2| The product has an LCD greater than 100 cm2
External electric cable| The product has external cables
The component contains refractory ceramic fibers| No used
The component contains radioactive substances| No used
Electrolyte capacitors (height > 25mm, diameter > 25mm)| Product has
electrolyte capacitors (height > 25mm, diameter > 25mm)
3. Tools Required
List the type and size of the tools that would typically can be used to
disassemble the product to a point where components and materials requiring
selective treatment can be removed.
Tool Description:
‐ Phillip head Screwdriver
‐ Hex Screwdriver
‐ Penknife
‐ Soldering iron and absorber
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>