gardenwize GW355 Freestanding Outdoor Patio Heater Instruction Manual
- June 6, 2024
- gardenwize
Table of Contents
GW355
Freestanding
Outdoor Patio Heater
Information For Use
Thank you for purchasing this Freestanding Outdoor Patio Heater from
Gardenwize.
This product is intended for use to keep you and your friends/ family warm &
cosy as you relax and socialise in your garden.
And with its IP34 waterproof grading, it is perfect for all year round usage
and helps to keep the cold at bay.
It is designed to be placed in your garden’s patio area.
It is also suitable for terraces and decking areas.
This patio heater uses three quartz tubes as its heating element to radiate
heat and is not designed for indoor use.
Product Elements
1. Heating Element Assembly
2. Knob
3. Body
4. Position Indication Plate
5. Pull Switch
6. Tube Cover
7. Upper Post Assembly
8. 3 -M5 x 6 Screw| 9. Middle Post
10. 3-M5 x 6 Screw
11. Lower Post Assembly
12. Clamp
13. Power Cord
14. Base Cover
15. 4-M6 x 30 Screw
16. Base Assembly
---|---
Assembly Instructions
Carefully remove all the product elements from the packaging.
IMPORTANT: This product comes unassembled out-of-the-box, however, the
supplied bolts are already screwed in place.
Please remove these bolts before assembling the product. You will need a
Philips screwdriver (not included).
1. Fix the bottom tube to the base using the 4pce M6 x 30mm screws.| 3.
Screw 3 x M5 6mm screws into the end of the upper tube and attach the cord
support clamp to the upper tube before fixing to the middle pole.
---|---
|
2. Screw 3 x M5, 6mm screws into the end of the middle
tube and attach the cord support clamp to the middle
tube before fixing to the base pole.| 4. Attach the cord support clamp to the
top part of the upper tube before, Then fix the heater head to the top tube
using the plastic screw in the heater head.
|
Once the patio heater has been assembled, place it in a suitable location in your garden and connect it to your main power supply.
Operating Instructions
Turning On/Off and Adjusting Heat Settings Once the patio heater is connected
to your mains power supply and in position, pull the pulley switch to turn on.
This patio heater has 3 heat settings. When you first pull the switch, the
heater will go to the first heat setting.
[1], which is the lowest setting.
Then on the second and third pull, the heater will go to the second [2] and
third [3] settings, with the third being the highest heat setting.
When the heater reaches the third set, and you pull the switch afterwards, the
heater will turn off.
The table below shows the wattage of each heat setting.
Heat Setting Wattage
1 650W
2 1350W
3 2000W
Adjusting the height and angle of the head
You can adjust the height of the patio heater via the height adjustment lock
located on the top. Simply rotate the lock anti-clockwise to unlock, set the
height and then rotate the lock clockwise to secure the height. To adjust the
angle of the head, ensure the heater is OFF and safe to handle, then simply
tilt to the required angle.
Replacing The Quartz Tubes
What You’ll Need: Philips screwdriver
If one of the quartz tubes is NOT functioning properly, then you will need to
replace it. To replace, please follow
the instructions below.
Ensure the patio heater is fully disconnected from the mains power supply, and
the heater is fully cooled down.
Carefully remove the heater unit from the standing pole.
Using a Philips screwdriver, unscrew the four screws behind the heater unit
and then carefully remove the back panel.
Next, remove the sheet metal guards on either side and then remove the faulty
quartz tube from the silicon sockets on either side.
Insert the replacement quartz tube and then replace the sheet metal guards on
either side.
Finally, replace the back panel and re-tighten the screws.
Health & Safety
This product is not a toy. Please keep children supervised at all times when
using this product.
When this patio heater is in use, the quartz tubes get very hot. Avoid close
contact with the quartz tube when in use. Risk of burn/injury.
When you are not going to use the patio heater for a prolonged period of time,
please place it in storage.
Never pour water directly onto the patio heater.
When replacing the quartz tube, please ensure the tube is fully cooled down.
Technical Support & Spare Parts
If you require any technical support & spare parts (including quartz tubes),
please contact us at
support@streetwizeaccessories.com
and provide the product name and supplier code (see Technical Specifications)
along with the technical query and proof of purchase.
Technical Specifications
| Product name | Gardenwize Freestanding Outdoor Patio Heater |
|---|---|
| Product code | GW355 |
| Quartz tube | 650W 40cm x3 |
| Voltage | 230V AC, 50Hz |
| Maximum Wattage | 2000W |
| Waterproof rating | IP34 |
| Adjustable height | 180cm to 220cm |
| Base dimensions | 50cm x 50cm |
Streetwize: Ashburton Road West, Trafford Park, Manchester M17 1RY
www.streetwizeaccessories.com
For product support:
E:
support@streetwizeaccessories.com
T: +44 (0)161 447 8597
For trade enquiries:
E: sales@streetwizeaccessories.com
T: +44 (0)161 447 8580
For spare parts:
E:
spareparts@streetwizeaccessories.com
EU Registered address: Ace Supply Co (Europe) Ltd.
25 Herbert Place, Dublin 2, D02 A098 Republic of Ireland.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>