OSP HOME FURNISHINGS VPR25 Vapor Gaming Chair Installation Guide
- June 6, 2024
- OSP Home Furnishings
Table of Contents
OSP HOME FURNISHINGS VPR25 Vapor Gaming Chair
ASSEMBLY INSTRUCTIONS
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert five Casters (A) into Base (B), push hard until you feel or
hear the Caster (A) snap into place. Insert Pneumatic Cylinder (C) into Base
(A) and slip Bellows (D) over Pneumatic Cylinder (C).
STEP 2 Attach Mechanism (E) to Seat Cushion (H) using four Bolts (1).
FULLY TIGHTEN ALL BOLTS USING ALLEN WRENCH (5).
STEP 3 Attach Arms (FL & FR) to Seat Cushion (H) using two Bolts (2) for
inner holes and two Bolts (3) for outer holes. FULLY TIGHTEN ALL BOLTS USING
ALLEN WRENCH (5).
STEP 4 Attach Back Cushion (G) to rear of Seat Cushion (H) using four
Bolts (4). FULLY TIGHTEN ALL BOLTS USING ALLEN WRENCH (5).
STEP 5 Place the assembled seat on top of Pneumatic Cylinder (C) and
apply downward pressure.
HARDWARE LIST AND PARTS
FEATURES
-
PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and pull lever (1) up.
To lower seat height sit on chair and pull lever (1) up.
NOTE: It is normal for chair to slightly lower under body weight. -
LOCKING TILT ADJUSTMENT
For individual comfort, this chair has been equipped with an adjustment that will allow the user to change the tension of the tilting feature. Turn knob (2) clockwise to increase tension and counter-clockwise to decrease or ease the tension. To lock return chair to the upright position and push lever (1) in. To unlock pull lever (1) out.
NOTE: Be careful not to loosen back tilt adjustment knob completely. -
ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (3) in to allow the arms to move up or down freely. Release the button (3) once the desired height is reached.
WARNING
- Use this product only one person at a time.
- Do not use this chair unless all bolts screws and knobs are securely tightened.
- Check that all bolts screws and knobs are tight every three months or as needed.
- Do not overturn back tilt knob when decreasing tension.
- Dispose of packing material properly. Do not use plastic cover as head covering. It may cause suffocation.
- Do not use chair as a stepladder.
- Use this chair for its intended purpose only.
- Use mild detergent only for cleaning.
OSP FURNITURE LIMITED PRODUCT WARRANTY
Design Lab Products
- 3 years on gaming desks and chairs
- Upholstery is not warranted against routine scratching and scuffing
All warranties are limited to the original purchaser for normal commercial
usage defined as a standard forty hour work week by persons weighing 250 lbs.
or less. This warranty will not cover labor, freight or damage from misuse,
abuse, negligence, alteration, accident, vandalism, rusting, acts of nature or
any other event beyond the control of Office Star Products. The warranty does
not cover cosmetic damage that may result from normal use. Liability for
incidental or consequential damages is excluded. The user assumes all risk of
injury resulting from use of this product. When usage is more than 40 hours
per week, a two year warranty on all parts applies. Fabric and foam is
warranted for one year. This warranty gives you specific legal rights, and you
may also have other rights
which vary from state to state.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components covered by warranty will be paid by Office Star Products.
Our quality standards are among the highest in the industry. Sometimes, no matter how hard we try, there are times when parts are damaged or missing. Our Parts Department will do everything possible to promptly remedy the problem. Contact us via e-mail [email protected], by Fax 1-909-930-5629, or toll free parts number 1-800-950-7262, Monday through Friday 8:00 a.m. – 5:00 p.m. Pacific Time.