UREPEL Smart Voice Color Changing LED Night Light User Manual

UREPEL Smart Voice Color Changing LED Night Light

At a Glance

Specifications

After-sale Service

• If you have any problems during use, Please contact our after-sales team first and leave us messages, We will contact you immediately.

Light Operation

Button Operation (Manual)

• Short press of the button will switch the light color/modes according to the following sequence:

Warm-Red-Green-Blue-Purple-Cyan-Pink-White-Yellow

• Fast Flash-Flash-Colorful Mode-Dynamic Gradient Mode
• Music Mode
• Long press to adjust to maximum or minimum brightness.

Voice Control Operation

Directly enter voice commands within 15 seconds after plugging into the socket.

• Common Voice Commands: Turn ON/OFF the Light, Change Color, Colorful Mode

If it takes more than 15 seconds after your last voice commands, you need to reactivate the device using the wake-up keyword before applying voice commands.

• Wake-up Keywords: Hey Light

Day/Night Time Mode

Day Time Mode (Default mode)

The light sensor is deactivated. You can change the device settings (color, brightness, lighting modes) using either voice commands or the operation button. The light will turn on when you switch to this mode.

Night Time Mode

The light sensor is activated; The device only operates when the surrounding light is dim. You can only adjust its settings (color, brightness, and lighting modes) using voice commands or the operation button after the device is turned on.

Note: Please note that you can only switch the modes via voice commands: “Day Time Mode” and “Night Time Mode”.

“Hey light” Wake-up keywords

• This command activates the light in two ways:

1. If the device is inactive for 15 seconds, it enters Standby Mode. To reactivate it, just say “Hey Light.”
2. When the device is powered off, say “Hey Light” to reactivate it, followed by “Turn on the light” after a single flash, and then give other commands.

Note: Upon plugging the device into the socket for the first time, it immediately lights up, allowing direct control through voice commands.

Important Safety Precautions

• Only fit the LED light in a properly power socket.
• Do not attempt to disassemble product.
• Do not allow this product to have contact with liquids.
• Do not place this product near a heat source or flame.
• Use soft cloth to clear the exterior. Do not use harsh chemicals or strong cleaning solvents.
• This device is not intended for use with emergency exits.
• Do not subject the device to knocks and vibrations. Knocks and vibrations may damage the sensitive electronics.

Voice Commands Table

feature, please use it if the light doesn’t respond to your voice commands.

The light will flash once to indicate its activation.

Day Time Mode| The light sensor is deactivated, you can change its status(color, brightness, lighting modes) with the voice commands or operation button.
NightTime Mode| The light sensor is activated, the device only works while the surrounding light level is low. You only can change its status (color, brightness, lighting modes) after it turns on.
Turn on the Light Switch on the light (Option}| The LED lights up.
Turn off the Light Switch off the Light topr/onJ| Switch off the light.
Change Color| Switch the light color in the following sequence: Warm-Red- Green-Blue-Purple-Cyan-Pink-White-Yellow
Colorful Mode| Quick command for breathing light mode.
Change the Mode| Switching four colorful lighting modes in sequence: Fast Flash-Flash-Colorful Mode-Dynamic Gradient Light
Music Mode| Make the light blink in sync with the rhythm of the music.

If no sound detected, the light will change to breathing light mode.

Brighten the Light| Increase in brightness level. (5 brightness levelsinclude) The light will fiash when reaching full brightness.
Dim the Light| Diminish in brightness level. (5 brightness levels include) The light will flash when reaching minimum brightness.
Maximum Brightness| Adjust the Brightness to Maximum level.
Minimum Brightness| Adjust the Brightness to Minimum level.
Warm Light| Change the light color to warm.
Red Light| Change the light color to red.
Green Light| Change the light color to green.
Blue Light| Change the light color to blue.
Purple Light| Change the light color to purple.
Cyan Light| Change the light color to cyan.
Pink Light| Change the light color to pink.
White Light| Change the light color to white.
Yellow Light| Change the light colour to yellow.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>