Mesko MS 4079 be 1.8 L Tabletop blender 500 W Beige User Manual
- June 6, 2024
- mesko
Table of Contents
Mesko MS 4079 be 1.8 L Tabletop blender 500 W Beige
Introduction
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE. PLEASE READ
CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial
purpose.
- Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
- The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
- The applicable voltage is 220-240V, ~50/60 Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
- Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
- WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
- After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
- Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
- Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
- Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
- Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
- Never use the product close to combustibles.
- Do not let cord hang over edge of counter or touch hot surfaces.
- Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
- In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
- Do not insert fingers or any other objects into blender’s cup when the blender is on.
- In order to avoid injuries handle the blades carefully.
- Watch out for long hair, scarves, neckties hanging above the cup and operating components of device.
- For safety reasons use only original accessories and spare parts intended for particular blender type, available at authorized service center.
- Handle the blades with extreme care while disassembling accessories. The blades can cause cuts.
- Do not wash any blender parts in dishwashers.
- Change the accessories only when the device is switched off. Disconnect the device from the power.
- Do not put any products other than food and liquids in the blender cup. Do not put hot products in the cup.
- The device is not suitable for whipping egg whites or kneading dough.
- Don’t use aggressive detergents to clean the housing, as it may remove the informational graphic symbols such as: scale, signs, safety marks, etc.
- Do not start the empty mixing cup, without product inside.
- MAXIMUM PERIOD OF CONTINUOUS BLENDER OPERATION IS 60 SECONDS. After 60 seconds of continuous operation stop the device and wait couple of minutes before restarting.
- Do not pour hot liquids (above 60 degrees Celsius) into the blender.
- If the blades are blocked, always disconnect the power cable plug from the power socket before removing the blocking elements from the blender cup.
- Do not move the appliance during operation.
DEVICE DESCRIPTION
- 1A – plug
- 1B – cover
- 1C – blender cup
- 1D – body
- 1E – speed adjustment knob
- 1F, 2A – Pulse function
- 1G – base of blender cup
- 2B – Off
- 2C -1 speed
- 2D – 2 speed
DEVICE OPERATION
Before first use:
- Remove all stickers and foils from the housing, cup and cover of the blender.
- Wash the device according to part „Cleaning and maintenance”.
Blender operation:
-
Put the blender main body (1D) on stable, level surface.
-
Make sure the speed adjustment knob (1E) is set to the Off position (2B).
-
Place the blender cup (1C) on the body (1D) and turn clockwise until cup is blocked on the base (1G).
-
Remove cover (1B) from the blender cup (1C), put in the ingredients to be mixed. In order to avoid overflow, the level of ingredients in the cup should not exceed ¾ of cup’s height.
-
Place blender’s cover (1B) on the blender cup (1C). Turn clockwise until cover is blocked. The padlock sign should be in position of blender’s handle.
-
Connect the power plug to the power outlet.
-
Turn the blender on by moving knob to the Pulse function (2A) or by rotating speed adjustment knob (1E) to slower speed (2C) or faster speed (2D).
NOTICE: During mixing always hold cup (1C) with hand. -
After the mixed products have proper consistence, turn the blender off by releasing Pulse button (2A) or by rotating speed adjustment knob (1E) to off position (2B). Wait until the blades stop. Remove the power plug from the power outlet. Remove the cup.
NOTICE: Do not allow continuous operation of blender for longer than 60 seconds.
NOTICE: The pulsation operation mode: when the Pulse button (2A) is moved, blender suddenly starts mixing with maximum speed.
SAFETY
Blender has two safety switches. One in the blender’s handle and second in the
blender’s base. Always check if cover (1B) and cup (1C) are placed properly on
the blender cup (1G) and body (1D). If not, blender will not start working.
During blending process, when cover (1B) is open the machine will stop
working. If blender is overload the motor will stop running. Wait about
45minutes for motor to cool down.
This blender jar is not suitable for grinding function.
CLEANING AND MAINTENANCE
Make sure that the blender is disconnected from the power.
- Wash the cups, covers and blades in water with washing-up liquid. In order to wash the cup thoroughly put some water with washing-up liquid in the cup, connect the blender to the power, and operate it for a short period of time in pulse mode. Then pour out the water, rinse thoroughly and dry.
- Clean the stained body (1D) with moist cloth, and then wipe dry.
NOTICE: Never immerse blender body (1D) in water or other liquids.
NOTICE: Do not wash any blender parts in dishwashers.
TECHNICAL DATA
Power: 500W
Voltage: 220-240V ~50/60Hz
Maximum continuous operation time: 60 seconds Minimum break time between work
cycles: 3 minutes
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.