mesko MS 7736 Fan Heater with Remote Control User Manual
- June 5, 2024
- mesko
Table of Contents
mesko MS 7736 Fan Heater with Remote Control User Manual
SAFETY INSTRUCTIONS
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
This Product is suitable only for occasional use or for use in well insulated
rooms.
The warranty conditions are different, if the device is used for commercial purpose.”
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240V, ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
-
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
-
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
-
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let cord hang over edge of counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power. In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
-
Never use this device close to water, e.g.: under shower, in bathtube, or above sink filled with water.
-
If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off.
-
Do not put your fingers or any objects through the ventilation grille
-
Do not place any objects on the convector. The vents must not be covered by a towel , curtain , etc. may cause a malfunction or fire.
-
Keep the distance between the convector and other items such as furniture , curtains.
-
Convector is equipped with a device to prevent overheating. Automatically turns off the convector in the event of excessive temperature convector (due to clogged vents, fan malfunction ) . In this case, disconnect the unit from the power supply , waiting a few minutes and remove the cause of overheating,
-
Do not touch the hot parts of the convector . Do not touch the appliance with wet hands.
In the case of wet convector or falling of any object through the ventilation grille of the convector , turn it off immediately and disconnect from the network. Before re- use with convector call for service . -
Do not place the convector directly below the electrical outlet.
-
Always turn off the convector button before disconnecting it from the mains.
-
Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
-
Do not use this heater if it has been dropped
-
Do not use if there are visible signs of damage to the heater
-
Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer.
WARNING: Do not use this heater in small rooms where there are people who are unable to leave them by themselves, unless constant supervision is ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other flammable materials at least 1 m away from the heater air outlet.
“Caution Hot Surface” – The temperature of accessible surfaces may be higher when the equipment is in operation, which means that the housing elements become hot during operation during operation, BE CAREFUL !!!
WARNING: In order to avoid
overheating – do not cover the heater. The device is not to be covered with
clothing, blankets and other textile products which could cause ignition.
BEFORE FIRST USE
This device should only be placed on a firm level surface and a minimum 50cm distance from walls and from the top as well as 120cm at the front.
Device description: Ceramic heater – Figure 1
A: Control panel
B: Air outlet
D: Base
Figure: 1
F: Main switch
C: Air inlet
E: Remote control
Control panel and remote control description – Figure 2
-
Standby button
-
Timer button
-
Oscillation button
-
Heating level button
-
Temperature setting button
5A. Temperature increase button
5B. Temperature decrease button -
Fan mode indicator
-
Digital temperature / timer display
-
Timer indicator
-
Heating level indicator: Low (white) / high (red)
-
Time unit indicator
-
Temperature unit indicator
-
Stand-by indicator
OPERATION
- Plug the device into the mains socket.
- Turn on the main switch (F) on the back side of device.
- Press the standby button (1) on the control panel (A) or on the remote control (E), the device will start working, press it again to turn off the device.
- Press the timer button (2) on the control panel (A) or on the remote control, you can set up the time from 1 hour to 12 hours by repeated pressing the button.
- Press an oscillation button (3) on the control panel (A) or on the remote control, the device will swing from right to left, press it again to stop this function.
- Press the heating level button (4) on the control panel (A) or on the remote control, you can select:
- fan mode, it is preset mode so the fan indicator (6) will be light up at screen all time,
- low heating level mode 1000W – by one pressing, the heating level indicator (9) will be light up in white color at screen,
- high heating level mode 2000W – by second pressing, the heating level indicator (9) will be light up in red color at screen.
- .Press temperature setting button (5) on the control panel (A) or temperature increase button (5A) / temperature decrease (5B) button on the remote control in order to set the temperature from 20°C to 40°C. The device will remember set temperature and after 5 times flashing the digital display (7) will show present room temperature. After few minutes the control panel will stop display any figures to do not disturb your sleeping process.
- When your device is working on heating mode, then you press standby button (1) to turn off your device, the device will keep working at fan mode to cool down the inside of the appliance for 30 second. Then it turns off and goes into standby mode. Turn off the main switch (E) at the back of the unit.
Remote control (E) operation is same as manual operation of buttons on control panel.
To use the device with the remote control (E) supplied, pull the installing
film. In order to remove the battery, simply squeeze the small tab and pull –
look at picture on page 3. Insert 1 x CR2025 (3V) lithium battery into the
small crevice.
IMPORTANT: The + symbol on the battery inserted should be facing upwards.
Firmly close the battery compartment to begin using the Remote Control (E).
SAFERTY PROTECTION
- OVERHEAT PROTECTION: This device is fitted with a safety overheat protection device. If overheating occurs, ensure the power switch is off and turn off the power supply. Unplug the device and let it cool down for 30 minutes. If something is obstructing air inlet, ensure the object is removed. Check with unit appearance, power cord and plug if no damaged before switch on again. Next, after 30 minutes has passed, turn the device on.
- TIP-OVER SWITCH: The device will work on a firm stable surface only. If the device is not 100% stable, vertical position, the unit will switch off until placed in the correct upright position.
CLEANING AND MAINTENANCE
- Make sure the device is not hot.
- Before cleaning the device remove the plug from the electrical socket.
- Keep the air inlet and outlet openings clean. Do not allow dust to collect on the openings.
- Clean the housing using only dry or moist cloth.
- Do not immerse the device in water!
- Before a long time storage take the battery away the remote control, then re-packed the device in its original packaging and stored in a cool and dry place.
TECHNICAL DATA
Voltage: 220-240V ~50/60Hz
Power: 2000W
Battery: 1 x CR2025 (3V) lithium battery included
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.
More Products
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>