Dimplex Optional Remote Control User Manual
- June 6, 2024
- Dimplex
Table of Contents
Installation Guide Optional Remote Control
Model Numbers:
BFRC-KIT
BFRC-KIT-OP
IMPORTANT SAFETY INFORMATION: Always read this manual first before
attempting to install it. For your safety, always comply with all warnings and
safety instructions contained in this manual to prevent personal injury or
property damage.
To view the full line of Dimplex products, please visit
www.dimplex.com
Always use a qualified technician or service agency to repair this fireplace.
NOTE: Procedures and techniques that are considered important enough to
emphasize.
CAUTION: Procedures and techniques which, if not carefully followed, will
result in damage to the equipment.
WARNING: Procedures and techniques which, if not carefully followed, will
expose the user to the risk of fire, serious injury, or death.
****Welcome & Congratulations
Thank you and congratulations for choosing to purchase an electric fireplace
from Dimplex, the world leader in electric fireplaces. Please carefully read
and save these instructions.
CAUTION: Read all instructions and warnings carefully before starting
installation. Failure to follow these instructions may result in a possible
electric shock, fire hazard and will void the warranty.
NO NEED
TO RETURN TO THE STORE
Questions with operation or assembly? Require Parts Information? Product
Under Manufacturer’s Warranty?
Contact us at:
www.dimplex.com/customer_support
For Troubleshooting and Technical Support
OR Toll-Free 1-888-DIMPLEX
(1-888-346-7539) Monday to Friday 8:00
a.m. to 4:30 p.m. EST
****IMPORTANT INSTRUCTIONS
- Read all instructions before using this appliance.
- Any repairs to this appliance should be carried out by a qualified service person.
- Under no circumstances should this appliance be modified. Parts having to be removed for servicing must be replaced prior to operating this fireplace again
- Do not use outdoors.
- Use this appliance only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
SAVE THESE INSTRUCTIONS
Remote Kit Installation
Installation Set-Up
- Open steel curtain (remove glass doors if applicable).
- Remove two screws on the log grate and remove the log grate. (FIGURE 1)
3. Pull the front edge of the plastic ember bed grate up and forward until the rear tab is released from the ledge located at the bottom of the mirror. (FIGURE 2)
NOTE: Log set fits tightly into the firebox, some force may be necessary to remove.
4. Locate and remove the two screws on the removable bracket. Remove the
bracket.
(FIGURE 3)
5. Locate and depress the mounting tabs on the plug connector to remove the
‘dummy plug’.
(FIGURE 3)
NOTE : Keep the ‘dummy plug in a safe place. You will need it if you
decide to uninstall the remote control to operate the fireplace manually.|
Install Remote Control Receiver
- Locate and insert the plug connector on the remote control bracket into the plug connector on the fireplace. (FIGURE 4)
- Place antenna under the remote bracket.
3. Locate and install the two screws on the remote control bracket.
4. Replace the log by inserting the front edge and pushing the back down
until the rear tab snaps under the back ledge (FIGURE 2) and the logs are
resting against the mirror.
5. Replace the log grate using two screws previously removed.
Operation
Remote Control
The remote control has a range of approximately 50ft. (15.25m). It does not
have to be pointed at the fireplace and can pass through most obstacles
(including walls). It is supplied with one of 2, 187 independent frequencies,
in the factory, to prevent interference with other units.
Remote Control Initialization/ Reprogramming
Follow these steps for remote control initialization and if required, re-
initialization:
- Ensure that power is supplied through the main service panel.
- Access the manual controls, (remove the glass doors if applicable) pull the right-hand steel curtain to the outside of the unit. (FIGURE 5)
- Locate manual controls.
- Move the 3-way switch to “Remote”.
- Activate the main power switch, the red Level 1 Indicator Light will flash . (Figure 6-D)
- Press and hold the On button on the manual controls (Figure 6-A) for five (5) seconds. The Level 1 Indicator Light (Figure 6-D) will then flash for 10 seconds.
- Within 10 seconds press the ON button located on the remote control transmitter. (Figure 7) This will synchronize the remote control transmitter and receiver.
Remote Control Usage
The remote control operation can be adjusted, depending on the season and
desired effects, by toggling the main mode selector switch built into the
fireplace. The position of the switch will dictate the available functions
that the remote transmitter will cycle through.
A. On Button
Pressing this button toggles sequentially through the three levels of the
fireplace.
- Mode Selector Set at “O”: Only Flame Effect at all 3 levels.
- Mode Selector Set at “–”: Pressing once activates Level 1 – flame effect only, two and three times activates Level 2 – flame effect and Fan.
- Mode Selector Set at “=”: Pressing once activates Level 1 – flame effect only, twice activates Level 2 – flame effect and Fan, three times activates Level 3 – flame effect, Fan and heat.
B. Off Button
Pressing this button at any time will shut the unit off.
C. Manual Selection Switch
Switches the operation of the fireplace between the different modes of the
fireplace:
- OFF (center): Makes the unit inoperable.
- MANUAL (top): All functions of the fireplace are controlled by the On and Off buttons as described above (A, B).
- REMOTE (bottom): All functions of the fireplace are controlled by the Remote Control.
D. LED Indicators|
Depicts which of the three (3) levels the fireplace is currently operating
at Level 1 – , Level 2 – or Level 3 –
Maintenance
Battery Replacement
(Figure 7)
To replace the battery:
- Slide battery cover opens on the handheld transmitter.
- Correctly install one (1) 12 Volt (A23) battery in the battery holder.
- Close the battery cover.
Warranty
All Dimplex accessories are warranted against defects in workmanship and
materials for two years from the date of sale. This warranty does not apply to
damage from an accident, misuse, or alteration, nor where the connected
voltage is more than 5% above the nameplate voltage, nor to equipment
improperly installed or wired or maintained in violation of the instruction
sheet. This limited warranty applies only to purchases made in any province of
Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any
of the 50 States of the USA (and the District of Columbia) except for Hawaii
and Alaska. This limited warranty applies to the original purchaser of the
product only and is not transferable. No other written or oral warranty
applies. No employee, agent, dealer, or other person is authorized to give any
warranties on behalf of Dimplex.
The customer shall be responsible for all costs incurred in the removal or
reinstallation and shipping of the product for repairs. Within the limitations
of this warranty, inoperative units shall be returned to the nearest Dimplex
authorized service center, and we shall repair or replace, at our option, at
no charge to you with return freight paid to be Dimplex. It is agreed that
such repair or replacement is the exclusive remedy available from Dimplex and
that DIMPLEX IS NOT RESPONSIBLE FOR DAMAGES OF ANY KIND, INCLUDING INCIDENTAL
AND CONSEQUENTIAL DAMAGE. Some states do not allow the exclusion or limitation
of consequential damages, so the above exclusion or limitation may not apply
to you. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
www.dimplex.com
Dimplex North America Limited
1367 Industrial Road
Cambridge ON
Canada N3H 4W3
© 2017 Dimplex North America Limited
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>