MAXBIK MX-16 14 inch Foldable Electric Bike User Manual

MAXBIK MX-16 14 inch Foldable Electric Bike

Diagram of e-bike-specific components

1. Handlebar
2. Front fork
3. Tyre
4. Saddle
5. Battery
6. Controller
7. Chainwheel & Crank
8. Motor

Specification

• Frame: 14 inch aluminum-alloy Motor: 300W brushless
• Battery: lithium battery,48V 10Ah
• Sensor: speed sensor 1:1
• Brake: F/ R Disc brake
• Charger: 110-220V optional
• Charge time: 4-6 hours
• Max speed: 25km/h
• Range: 50km
• Max loading: 140kg

How to use

1. The process of opening and working.
   • Open the quick release, then discharge the seat
   • Put the battery into the battery container beside the seat tube and to the end from lead rail and keep it connect well and stable.
   • pls connect the power plug to Battery box 
   • After that and then lock the battery(the key in the middle)
   • Turn on the power(turn left the key under the battery box)
   • turn on the main switch on right grip
   • go to ride like normal bicycle with pedal assistance or throttle
2. The process of closing.
   • Stop ride and keep the bike is not moving.
   • Turn off the switch button on the display.
   • Turn off the switch button under the battery box. Turn on the key when you want to take out the battery box.
3. Warning
   • Keep the connection( motor and battery ) is well and stable before ride.
   • Don’t turn on/off the switch button(battery and display) when you a riding.
   • Keep fix well the QR of seat post and pedal are fixed.

Important safety notes concerning the battery

To prolong battery life, store the scooter in garage to prevent low temperatures and affect the battery performance.

• Do not dismantle or dispersed the battery cells.
• Keep away the battery from children.
• Do not connect cathode and anode of charger during charging and discharge process. Prohibited to use any conductor to connect both cathode and anode. This will cause short circuit.
• Prohibited battery dip in the water.
• Prohibited placed the battery in a temperature over 60℃ next to a high-temperature heat source, such as ingle, heating, etc.
• Prohibited knock-on, throwing and trample the batteries, etc.
• Prohibited edge tool or nails lacerate and cut through the battery.
• If the leak occurred, electrolyte has come into the eyes, please do not rub. Wash immediately with plenty of water.
• If the battery in smell, heat, smoke, changed colors, distortion or any abnormal, stop using the battery and away from it immediately.

Protection

To extend the battery life and be Intelligent Use of Li-battery, here are the regulations:

1. Firstly: Requirements on charging and discharging
   • charge:the charger must be the assorted one. First, connect the power to the charger. second, insert the charger’s out-put connector to the battery’s input connector. Third, when the signal light is on, please pull out the battery’s input connector first. The common single charging time is about 6-8 hours.if the battery be blow-up, the charging or discharging must be stopped.
   • avoid discharge: charge the battery timely after discharging, in order to avoid over-discharge.
2. Secondly: Requirements on storage
   • Li-battery cannot be stored at the place where is over hot and over humidity. therefore the temperature of the storage should between -20 to 55degree,and furthermore, the storage must be kept in dry,clean and the battery should not be piled up.
   • the battery cannot be stored for a long time without charging. The battery should be charged once a month. The battery should be stored with fully charged.
3. Thirdly: Maintenance
   • When you test the voltage of the single piece of the battery cell, you have to test the cell directly, not by the wire. By doing that, it can avoid the voltage decline.
   • You have to wear the gloves or clip the fingernails before you take out the single piece of the battery. So as to avoid damage the cover of the battery.
   • Forbid bending the battery cell, the top edge of the seal-up.And also falling, hitting and short circuit are prohibited.
   • When you re-assemble the battery, there are some special notes we have to concern in mind. The temperature of the
     electric iron should below 350℃; the welding time must be less than 3 seconds, and the frequency of welding should be no more than 5 times;the second welding must be done after cooling.

Charger function

Trouble shooting

Should there be any difficulties with charging please check if:

• the power cable is connected properly.
• the charger plug or the battery socket is damaged.
• the battery shows any damage on the surface.
• the power socket works and whether the correct voltage is provided. (if necessary, plug in another gadget and check).
• Please use only the original charger which was supplied with the supplier

This charger is specially made for lithium battery. The LED light indicates the battery status as shown on the table below:

Charging cycle and LED indication for lithium battery

LED| Mode
green| the battery is not connected
red| the batter is charging
green| the battery is charged, the charger switches off

Important safety notes concerning the charge

Before you first use the charger please read the following notes regarding safety carefully!

• Keep the charger away from children!
• In order to prevent any possible injury this charger should only be used for the original lithium battery which is supplied together with the WBLDDC. Any other battery is not compatible and risks exploding while charging, causing serious injury to people as well as damage to other equipment.
• Using this charger for batteries not supplied by WBLDDC,for the E-RIDE could risk catching fire, provoke electric shock and/or cause serious injury.
• Please make sure that the charger is always kept dry and does not get wet at any time.
• Should there be an incidence of contact with water or any other liquid,make sure to unplug the charger immediately from the power socket and have it inspected by a specialty dealer.
• Make sure the charge is always placed on a flat surface when in use.
• Please make sure that the charger is always unplugged tand removed from the power socket when not in use.
• Before using the charger, always make sure that the plug and the cables are not damaged.
• Never connect a damaged cable or plug to the power socket.
• Never try to disassemble the charger. Wrong re-assembling could cause an electric shock and serious injury.
• Always unplug the charger before cleaning it.
• The charger should only be cleaned with a dry cloth. Never use a wet cloth, oil or any other liquid.
• Do not use an extension cable. Only use the original cable supplied with the charger.
• An extension cable might, if not 100 % compatible, catch fire or cause an electric shock.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>