Glazata S80 Wireless Bluetooth Headset with Multi Microphone User Manual
- June 6, 2024
- Glazata
Table of Contents
1 . Product specifications
2 . Product description
3 . Function description of each component
4 . Headphone charging 5. Pairing method
5.1How to pair a single phone or another device
5.2How to connect a computer without Bluetooth
5.3 How to connect two devices at the same time (one for two)
|
6 . Basic operation
6 . 1 Boot
6 . 2 Shutdown
6 . 3 Start a call
6 . 4 Function Function
6 . 5 Volume adjust
6 . 6 Music play/pause
7 . Matters needing attention
8 . Important safety precautions
9 . Packing list
10 . Frequently Asked Questions
---|---
Bluetooth Ver.5.0 Bluetooth earphones
In this manual, the product name is replaced by “S80”.
Thank you for purchasing our products.
This manual describes how to use the 580 Bluetooth headset and precautions.
Please read the instructions carefully before using this product. In addition,
please keep this manual properly for reading at any time.
If the product you purchased fails, you can contact our after-sales
department, we have a comprehensive after-sales service.
After-sales E-mail: [email protected]
Product specifications
Product description
S80 is a high-definition call Bluetooth headset made for business people. Using Qualcomm 3020 chip, equipped with dual-mic feedback noise reduction technology, through dual MIC array, automatically reduce environmental noise, accurately calculate the caller’s location, present pure sound quality and clearer voice calls such as face-to-face conversation. It supports aptX and aptX-HD and is compatible with AAC/SBC and other formats, decodes more music details, and brings more shocking music enjoyment.
Function description of each component
| Power switch | (ON means power on; OFF means power off. |
|---|---|
| Multi-function key | Answer/Reject/Call back /Hang up/Play/Pause. |
| Adjustment key | Used for volume adjustment or music switching. |
| LED light | Headset status indicator. |
| Ear caps | Used for sound insulation and increased wearing comfort. The spare |
ear caps are available in three different sizes: L/M/S.
Charging port| Use a USB Type-C charging cable to charge.
Headphone charging
Please use a charger with an output power of 5V1A or less to charge the headset. Charge before use.
- Plug the included charging cable into the headset charging port.
- Connect the other end of the charging cable to a 5V1A charger or to the USB port of the computer.
- when the LED indicator is red, it means charging is in progress; when the LED indicator turns blue, charging is complete
Pairing method
5.1How to pair a single phone or another device
-
Turn on the headset (turn the power switch to the ON position).
-
S80 Bluetooth headset automatically enters the search and pairing state __
-
Turn on the Bluetooth of the mobile phone or another device.
-
Click search, when “S80– is found, click pairing, and then wait for the pairing to succeed.
(After the pairing is successful, the indicator light will flash blue once every 10 seconds.)
5.2How to connect to a desktop PC
- Download and install a universal Bluetooth driver.
- After installation, Plug in the Bluetooth adapter.
- When the S80 Bluetooth headset is in the search and pairing state, right-click the computer’s Bluetooth icon interface and select “Search Device’; then it will search for nearby Bluetooth devices and select “S80”, click to complete the connection.
5.3How to connect two devices (one for two)
1. After connecting the first device, turn off the Bluetooth of the first
device. the headset re-enters the search pairing state (red and blue lights
flashing).
2. Turn on the Bluetooth of the second device, search for “S80” and click on pairing.
3. After the second device is successfully paired, turn on the Bluetooth of
the first device again, and the headset will automatically connect back to the
first device.
After one or two connections, the headset will play the sound of the current
device by default
When switching devices, you need to turn off the device that is playing. (When there is an incoming call, the Bluetooth headset will play the device with the incoming call first).
**Basic operation
**
6.1 Boot
Turn the power switch to the “ON” position, the indicator light flashes, about
2 seconds later, the red and blue lights flash, and the headset enters the
search and pairing state.
6.2 Shutdown
Turn the power switch to the “OFF position, the red indicator light will
stay on for one second and then go out, which means it is off.
6.3 Start a call
- After the headset and mobile phone are paired successfully, you can start a call.
- When a call comes in, short press the multi-function button to answer; press again to hang up the call.
- When a call comes in, press and hold the multi-function button for about 2 seconds and then let go to reject the call.
- Press the multi-function key twice in succession to redial.
6.5 Functions operations
6.5 Volume adjustment
Short press the volume “+” key to increase the volume; short press the volume
“2 key to decrease the volume.
Note: Some devices do not support Bluetooth volume synchronization. You
need to adjust the volume of the phone to the maximum first, and then adjust
the Bluetooth headset.
6.6 Music play/pause
1. Play/Pause: Short press the multi-function button.
2. Previous song: Long press the volume “2 buttons for about 2 seconds
3. Next track: Long press the volume “+” button for about 2 seconds
Matters needing attention
Due to differences in mobile phone hardware or software, the screen of some
mobile phones will not display the remaining battery power of the Bluetooth
headset.
*The standby time of the Bluetooth headset varies with the volume and environment during use.
*The effective distance of the Bluetooth signal is more than 10 M, you can use the Bluetooth headset within 3-5 meters, because the too long distance will cause signal weakening/loss/ interference caused by the mobile phone transmitting
wireless signals, and you will hear intermittent sounds at this time Or the
sound is poor or even disconnected (the headset will try to reconnect after
disconnecting and returning to the effective distance).
*If you do not use this product for a long time, please store it in a dry environment, and charge the headset at least once a month to extend its life and avoid extreme temperatures and dust.
Important safety precautions
- Never use corrosive cleaning agents to clean this product.
- Do not let this product be heated or close to a fire source, such as a cooking stove.
- Do not expose this product to direct sunlight for a long time.
- Do not dispose of this product in the fire to avoid explosion.
- Do not try to disassemble this product to make any modifications, because it does not contain any maintenance components.
- The waterproof level of this product is life waterproof, please avoid the earphones from being exposed to heavy rain.
Packing list
S80 Bluetooth headset1
Types charging cable1
Manual1 Ear caps (L/M/S)3
Retractable ear hook*1
Frequently Asked Questions
Q: The mobile phone can search for Bluetooth, but cannot be paired
successfully? Answer: The Bluetooth program of the mobile phone may be
disordered. You can restart the mobile phone and the headset at the same time
and then connect again.
Q: Can’t the other party hear the voice sent by Whatsapp? Answer: Some mobile
phones do not fully support Bluetooth microphones. When recording or using
third-party software such as WhatsApp to send voices one by one, they can only
use the built-in microphone of the mobile phone by default. In this case, it
is recommended to update the phone to the latest version first; if the problem
persists, it is recommended to speak as close to the built-in microphone of
the phone as possible when you need to send one voice. Or directly use voice
calls or phone calls.
Q: Can I wear it on both left and right ears? Answer: Yes! The direction of
the rear cap and the direction of the ear hook can be turned at will, and the
comfortable angle can be adjusted arbitrarily according to your actual
situation.
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: ( I) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part IS of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions. may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.