GEG NC09 Active Noise Cancelling Bluetooth Headphone User Manual
- June 6, 2024
- GEG
Table of Contents
NC09
Active Noise Cancelling Bluetooth Headphone
User Manual
Thank you for choosing NCO9active noise-canceling Bluetooth headphones. Please read this manual carefully and use the following.
Features
-
Bluetooth Version: 5.0
-
Bluetooth profile: HSP, HFP, A2DP, AVRCP,APTX,APTX LL,AAC,SBC
-
Active Noise Cancelling solution: FF+FB (hybrid)
-
Type-C
-
Line in
-
ANC button
-
Volume down button/Next(-)
-
Multifunction button/Power on/Power off/ Paring/Play/Pause/Answer call/Reject call
-
Volume up button/Previous(+)
-
LED
-
Mic
How to use
- ANC Power on : ANC switch goes upward, Blue LED lighting
- ANC Power off ANC: switch goes downward
- Bluetooth power on: long press multifunction button for 1.5 seconds in power-off status, Blue LED lighting for 1 second
- Bluetooth power-off: long press multifunction button for 4 seconds in power-on status, Red LED lighting for 1 second
- Pairing: long press multifunction button for 5 seconds in power-off status, Red LED & Blue LED flashes alternately
- Volume up: Short press + button to volume up 1 step.
- Volume down: Short press – button to volume down 1 step.
- Play/Pause: Short press the Multifunction button to play or pause the music.
- Next: Long press 1.5seconds – button to move to next music in playing.
- Previous: Long press 1.5seconds + button to move to previous music in playing.
- Answer call: Short press the Multifunction button when incoming call.
- End call: Short press the Multifunction button is calling.
- Reject Call: Long press 1.5seconds Multifunction button when incoming call.
- Last number redial: In standby mode, double short press the Multifunction button.
- Charging: charging headphones by the DC 5V Type-C cable, Red LED keep lighting during charging, Red LED change into Blue LED when finished
- Reset: if the headphone fails to power on even after being fully charged or is unresponsive during use, please follow the steps below to reset it: Connect the headphone to the Type-C port or Type-C power adapter of the computer with a charging cable. The red led will light up to indicate that the headphone has been reset successfully, Red Led is always on
Specification
Stand-by time:
Playing music time:
BT on+ANC on:
Wireless range:
Speaker:
Sound pressure level:
Frequency Response:
Weight:| 900h
20h
15h
10m
040mm
98±3dB
20Hz- 20 KHz
270g
---|---
Kit Contents
1 X Headphone
1 X Type-C Cable
1 X User Manual
1 x 3.5mm jack audio cable
Warning
- You must choose a qualified charger(Output=5V) from a regular manufacturer to charge the headphone.
you must charge the headphone if it has not been used for more than 12 months.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.