Ibanez WS1 Guitar Wireless System Owner’s Manual

Ibanez WS1 Guitar Wireless System

OWNER’S MANUAL
http://www.hoshinogakki.eo.jp/pdf/ibanez/
manual/en/electronics/WS1.pdf

Before using this device. be sure to read this manual thoroughly for safe use of it. After that, keep this manual in a safe place and read ij whenever necessary.

Safety Precautions === Be sure to observe the following precautions ===
In order to use this device properly, the contents to be observed are explained, classified as follows.
The severities of the injury and damage due to incorrect usage by ignoring the written contents are explained by the following classified indications.

Warning Indicates a potentially hazardous situation which, if not avoided, will result in death or serious injury.
Cautions Indicates a potentially hazardous situation which, if not avoided, will result in injury or property damage.

The contents to be observed are explained, being classified by the following pictograms.

• This pictogram shows a compulsory action, something that you must do.
• This pictogram shows a prohibition, something that you must not do.
• This pictogram shows a notice, something that you need to be alerted to.

Warning :
Never disassemble or modify the device
Do not operate with wet hands. «A short circuit or an electrtc shock may occur.»

Cautions

• Avoid water, moisture, dust and high temperature
  Do not store or use the device in places such as a bath or outdoors where water splashes. Also do not use it in places of high humidity, places with a lot of dust, or at high temperatures.
  «A fire, an electrtc shock or a failure may occur.»

• Do not store in places of excessive vibrations
  «It may cause a failure.»

• Do not apply excess force, drop nor give strong physical impact
  «A failure or injury may occur.»

• Do not use thinner, alcohol, and the like for cleaning
  <>

Transmitter

Receiver

Part names and uses

1. Charging inlet (micro USB Type-B)
   You can charge the wireless units by using a micro USS Type-8 Y-cable (included) with your own USS power adapter.
   NOTE: While charging, the LED 0 lights red and WS1 doesn’t work as a wireless system. When it’s fully charged, the LED 0 turns off.

2. Power button
   Press and hold this button to turn on the transmitter and receiver.
   Before they get paired automatically, the LED 0 blinks/flashes and indicates the remaining battery level as followings.

   • Green: 100%-75%
   • Yellow: 75%-50%
   • Red: 50%-25%
   • Red flashes 10 times: less than 25%.
     The power turns off automatically to protect battery life.
     After 2 seconds, they will be paired automatically and both of the LEDs 5 lights green.
     The WS1 will choose the best wireless channel automatically in 2.4 GHz frequency band. If the receiver can’t detect a signal coming from the transmitter, the receiver’s LED 0 will blink red.

3. Transmitter plug (1/4″)
   Connect the transmitter to the output of your guitar.

4. Receiver plug (1/4″)
   Connect the receiver to the input of your amp or pedal. Before plugging-in, we recommend you turn off the power of your amp to avoid any possible damage to the amp.

5. LED indicator
   Shows the current status of the wireless units.

6. Cable tone
   You can switch the cable tone mode on and off by clicking the power button 2 on the transmitter.
   The WS1 has a cable tone filter function which simulates a 3 m (10 fl.) high grade guitar cable connecting to a passive guitar. By clicking the power button 2, the cable tone filter is engaged and LED e lights orange. This mode will deliver a more natural electric guitar tone.
   When the cable tone mode is off, LED 5 lights green. It is default setting which doesn’t have any specific tone filter but flat frequency response. (Refer to the figure below)

• Automatic power off
  The WS1 transmitter will turn off automatically if it doesn’t detect any input signal for 10 minutes. The receiver will tum off automatically at 10 minutes after the transmitter turns off.

• ID matching
  The WS1 transmitter and receiver have already assigned unique matched ID at the factory. If you want an another WS1 transmitter or receiver to get paired, follow the following steps to reset ID matching.

1. Tum off all the WS1 transmitter and receiver around you.
2. Press and hold the power button fJ of the transmitter and receiver you want to pair for more than 5 seconds.
3. While you press and hold, the receiver LED 111 will blink red. When the ID matching finishes, the receiver LED 111 will blink and light green. (Press and hold till the ID matching has been done.)

Specifications

0.40(L)x1.26(W)x1.00(H) in.

Weight| Transmitter: 36g / 0.0B!bs Receiver: 36g / 0.08Ibs

Simplified EU Declaration of Conformity
Hereby, Hoshino Gakki Co., Ltd. declares that the radio equipment type WS1 is in compliance wijh Directive 2014/53/EU. The full text of EU declaration of conformity is available at the following internet address: http://www.hoshlnogakkl.co.Jp/pdfnbanez/declaratlon/en/WS1.pdf

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been Jested and found 1o comply with the limits for a Class B digital device, pursuant 1o part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radia1e radio frequency energy and, not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a partiwlar installation. If this equipment does cause harmful interference to radio or television reception, which can be de1ermine by turning the equipment off and on, the user is encouraged 1o try 1o correct the interference by one of more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an ouHet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV 1echnician for help.

The device has been evalua1ed 1o meet general RF exposure requirement. The device can be used in portable exposure condition without resbiction. Any Changes or modifications not expressly approved by the party responsible for compliance could void the usefs authority 1o opera1e the equipment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>