Kelvin Hughes Mk7 SharpEye Radar Instructions
- June 6, 2024
- KELVIN HUGHES
Table of Contents
Mk7 SharpEye Radar
REMARQUE:
Chapter 2: Health & Safety notices
REMARQUER: RADHAZ FIGURES ARRÊT DE LA
ATTENTION: TEMPÉRATURE DU LOGEMENT
SAC DESICCANT AVERTISSEMENT: SAC DESICCANT GEL DE SILICE
CÂBLE À FIBRE OPTIQUE AVERTISSEMENT: PRODUIT LASER DE CLASSE 1
DANGERS ET PRÉCAUTIONS AVERTISSEMENT: RISQUES ÉLECTRIQUES
AVERTISSEMENT: TENSIONS AC TENSIONS RÉSIDUELLES
AVERTISSEMENT: CÂBLES À FIBRES OPTIQUES CASSÉS OU ENDOMMAGÉS
ATTENTION
Page 10 of 80
Chapter 2: Health & Safety notices
RISQUES DE CHUTE
MISE À LA TERRE/ POINTS DE TERRE
AVERTISSEMENT : CONDITIONS MÉTÉOROLOGIQUES
ÉQUIPEMENT DE LEVAGE AVERTISSEMENT
AVERTISSEMENT SÉCURITÉ ALOFT
PIÈCES DE RECHANGE DE LEVAGE PRÉCAUTIONS GÉNÉRALES DE LEVAGE
CORDON DE SÉCURITÉ
Page 11 of 80
Chapter 2: Health & Safety notices
MANIPULATION ANTISTAT STATIQUE
ATTENTION: MANIPULATI
–
PROCÉDURES DE LEVAGE CORRECTES ET INCORRECTES
Exemple de
Exemples de procédure de levage
procédure de levage
INCORRECTE
CORRECTE
ENTRETIEN ET RÉPARATION
DÉCLARATION de RoHS ÉLIMINATION EN FIN DE VIE
Page 12 of 80
3 System overview 3.1 Handbooks
Chapter 3: System overview
NUMBER HBK-1000 HBK-2300-1 HBK-2300-2 HBK-2300-7 HBK-2300-8 HBK-2300-S Note 2
DESCRIPTION
3.2 Low Profile Antenna (LPA-A3)
Note 1 Note 2
PART NUMBERS PART NUMBER LPA-A3 LPA-A3-BAAA
FITTING KIT
FINISH/ COLOUR
Note 1: Note 2:
Page 13 of 80
Chapter 3: System overview
3.3 Transceiver/ turning unit (DTX-A1-xxxx)
DTX-A1-XXXX
VARIANTS COVERED BY THIS HANDBOOK
PART NUMBER DTX-A1-ANKA DTX-A1-BNKA DTX-A1-BRMA DTX-A1-APNA
DESCRIPTION
SERVICE ACCESS PANEL
STATIC DESICCATOR SIGNAL CONNECTIONS
AC POWER APPLICATION
Transceiver
DESCRIPTION
Antenna motor MAIN COMPONENTS
FITTING KIT
Page 14 of 80
Chapter 3: System overview
3.4 Drive control unit (GTX-A24)
GTX-A24 DRIVE CONTROL UNIT
CONTROL ON / OFF KEYSWITCH
CONNECTIONS AND CABLE
AC SUPPLY
SUPPLY VOLTAGE
DESCRIPTION
220VAC GTX-A24:
110VAC GTX-A234 (OPTIONAL):
Page 15 of 80
3.5 Typical system
Chapter 3: System overview
Page 16 of 80
Chapter 4: Mechanical installation
4 Mechanical installation
The health and Safety notices shown at the beginning of this handbook must be
observed at all times when installing, terminating, commissioning, operating
and maintaining the equipment and its sub-
assemblies.
4.1 Pre-installation
4.1.1 Storage conditions PACKING
ENVIRONMENT:
STORAGE TEMPERATURE RANGE
4.1.2 Shelf-life ELECTRICAL Note
two years
WARRANTY
4.1.3 Equipment location/ positioning
HBK-1000: Radar installation guidelines & interpretation of display.
NOTE:
Page 17 of 80
4.1.4 Equipment inspection
Chapter 4: Mechanical installation
4.1.5 Fitting kits
SFP MODULES 4.1.6 Keys
CAUTION: SHIM WASHERS
Page 18 of 80
4.2 DTX-A1-xxxx
4.2.1 Mounting Plate
Mounting plate:
Chapter 4: Mechanical installation
Service platforms:
Gearbox platform surface:
Weight:
See section 4.2.7 for dimensions and 4.2.8 for details on the fitting kit.
Horizontal tolerance:
ILLUSTRATION NOTE
Page 19 of 80
4.2.2 Lifting
Chapter 4: Mechanical installation
The Health & Safety warnings and precaution noted at the beginning of this handbook MUST be observed at all times when lifting ANY equipment.
DO NOT LIFT WITH ANTENNA FITTED.
Refer to section 4.3 for details on lifting and installing the antenna.
ANTENNA NOT FITTED OK TO LIFT
4.2.3 Tools, torque setting & bolts TOOLS
MOUNTING BOLTS
TORQUE VALUES BOLT DESCRIPTION MAIN MOUNTING BOLTS SERVICE ACCESS PANEL
NOTE: MOUNTING BOLT LUBRICANT.
ADDITIONAL
ANTENNA FITTED DO NOT LIFT
TORQUE VALUE 80Nm 17Nm
Page 20 of 80
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>