Jianwei JM36D Venetian Blinds Motor Instruction Manual

Jianwei JM36D Venetian Blinds Motor

Products Description

Dimmer Venetian motor can realize smart control shutters. adjust angle by one button. There have dry battery and lithium battery + solar panel two solution can choice .Stand products can control by button and remote, also can customized control by APP.

Parameter

Setting Instruction

1. Enter setting status (After entering the code setting status, if the code setting is not successful within 10 seconds, the system will exit due to timeout and the indicator will off)

2. Match Code
   Notes : The receiver code with a maximum of 10 transmitters.

3. Change Direction
   Notes : In the process of change direction, the motor will enter the status of code first (Press the indicator light for3s it will blink slowly}, do not care about it, press until 5s, and then the indicator light will blink quickly then off.

4. Tilt & continuous move convention

5. Delete single code

6. Motor control
   Tilt status
   Remote control

   • Press “UP”key within 1s, motor tilt until limit.
   • Press more then 1 S,motor move up.”STOP”key for stop motor, Press “DOWN”key within 1s , motor tilt until limit.
   • Press more then 1 S,motor going down.
     One key for moving to middle limited
     Under stop status, Press”Stop” key of remote, Motor automatic move to middle limited.

7. Limit setting
   Method 1: Automatically limit setting
   Motor move up and down two times, stop on block twice at same position, It will have memory of these positions.
   Notes : Only up and down limit can be automatically setting, the third limit could not. If stop on block position are different every time, last position will be memory.
   Method 2: Manual limit setting

8. Adjust the limit position
   

9. Delete the middle Limit point
   ( Note : The limit point will not be deleted if you press the back button for 5 seconds when it is not in the middle limit point.)

10. Low power remind

11. Restore factory Settings

Installation instructions

1. Take off the gasket paper of 3m adhesive and put on the position you want beside of the shutter;
2. Choice 64mm or 89 mm clip which is suitable for slat width;
3. Push clip into the drive rod of motor;
4. Suggest install by screw which is suitable for the motor back hole;
5. Install solar panel by suckers where is under sunshine.

Attention

1. Do not touch the circuit board with bare hands to avoid static electricity damage;
2. Do not plug in the charging power supply when the dry battery is supplied;
3. When the dry battery is out of power, please replace the new battery in time. Do not reuse the dead battery to avoid the loss of the limit point;
4. When using lithium battery power supply, it must be charged in time.

Troubleshooting

No response to button

| 1. Check whether the motor is in good contact
2. Make sure the battery is fully charged| 1. Reload the battery

2. Change dry battery or lithium battery

Limit point offset

| Confirm whether there is a large friction force or foreign body obstruction in the process of operation, resulting in the same .| ****

Restore factory Settings, reset the limit point

Center the code setting, but short press the button motor no action| Confirm whether there is a large friction force or foreign body obstruction in the process of operation, resulting in the same| Restore factory Settings, reset the limit point.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>