Changzhou Jianwei JWBT-02 Bluetooth Module Remote Control Instruction Manual
- March 14, 2024
- Changzhou Jianwei
Table of Contents
**Changzhou Jianwei JWBT-02 Bluetooth Module Remote Control Instruction Manual
**
Introduction
JWBT-02 Bluetooth module is Guangzhou Jiangxi Electric Co., Ltd.The company is
specially
designed for intelligent wireless data transmission of electric vehicles.It
adopts the YC3121 chipof China Yizhaowei Company, and the chip is dual Core
configuration, M0 and BT run independently without interfering with each
other. On-chipSet 1MB Flash 33 IOs for customers to use.
Footprint
Dimensions
Labeling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modification warning.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Information to the user
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. -
Consult the dealer or an experienced radio/TV technician for help
RF warning for Mobile device
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cmbetween the radiator & your body.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEMManual v01 guidance, the following conditions must be strictly followed when usingthis certified module:
KDB 996369 D03 OEM Manual v01 rule sections:
List of applicable FCC rules
This module has been tested for compliance to FCC Part 15C 15B
Summarize the specific operational use conditions
The module is tested for standalone mobile RF exposure use condition. Any
other usage conditions such as co-location with other transmitter(s) or being
used in a portable condition will need a separate reassessment through a class
II permissive change application or new certification. 2.4 Limited module
procedures
Not application
Trace antenna designs
Not application
RF exposure considerations
This equipment complies with FCC mobile radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated multivitamin distance of 20cm between the radiator & your body. If
the module is installed in a portable host, a separate SAR evaluation is
required to confirm compliance with relevant FCC portable RF exposure rules.
Antennas
The following antennas have been certified for use with this module; antennas of the same type with equal or lower gain may also be used with this module. The antenna must be installed such that 20 cm can be maintained between the antenna and users.
Label and compliance information
Label and compliance information The final end product must be labeled in a visible area with the following: “Contains FCC ID: 2A4MI-JWBT-02 ”. The grantee’s FCC ID can be used only when all FCC compliance requirements are met.
Information on test modes and additional testing requirements
This transmitter is tested in a standalone mobile RF exposure condition and
any co-located or simultaneous transmission with other transmitter(s) or
portable usewill require a separate class II permissive change re-evaluation
or new certification.
Additional testing, Part 15 Subpart B disclaimer
This transmitter module is tested as a subsystem and its certification does
not cover
the FCC Part 15 Subpart B (unintentional radiator) rule requirement applicable
to the final host. The final host will still need to be reassessed for
compliance to this portion of rule requirements if applicable. As long as all
conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product
for any additional compliance requirements required with this module
installed.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC
authorizations
no longer considered valid and the FCC ID can not be used on the final
product. Inthese circumstances, the OEM integrator will be responsible for re-
evaluating theend product (including the transmitter) and obtaining a separate
FCC authorization.
Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the
endproduct which integrates this module. The end user manual shall include all
requiredregulatory information/warning as show in this manual
OEM/Host manufacturer responsibilities
OEM/Host manufacturers are ultimately responsible for the compliance of the
Host and Module. The final product must be reassessed against all the
essential requirements of the FCC rule such as FCC Part 15 Subpart B before it
can be placedon the US market. This includes reassessing the transmitter
module for compliancewith the Radio and EMF essential requirements of the FCC
rules. This module must not be incorporated into any other device or system
without retesting for compliance as multi-radio and combined equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>