Shenzhen Ledodm Lighting DC-BlTl0-1 RGB LED Rock Light User Guide

RGB LED Rock Light User Guide

THANK YOU for choosing MustWin. To optimize user experience, please install and use the light according to the following instruction.

Warning

1. Please check if the light and the parts are intact before installation.
2.  Make sure to cut off the power before installation.
3. Please do not place this light in corrosive conditions.
4. If there is any damage to the cord, please cut off the power and stop using it immediately.
5.  Wrong connection may lead to this suite getting damaged, the warranty range is excluding the damage caused by the wrong connection.
6. To ensure the light works properly, please use the voltage indicated on the packing.
7. To avoid any damage to the light, please do not use chemical solvent during routine maintenance.

Specification

control
Battery for Controller| CR2032/CR2025
remote control distance| Maul Orn
Lamp Brand| 5050RGB
Lite Span| 30000H
Working Temperature| -40-60°C

1. Use screws or tape to stick the lamp under the automobile chassis.
2. Use the cable to fix the light wire on the automobile chassis.
3.  Please do not expose the controller to the outside in case of being influent.

Tips: When it’s powered, please wait 2-3 seconds, then turn on or turn off the light.

Three Control Methods

Type A: Bluetooth APP Installation

http://www.easytrack.net.cn/download/177ODM/LEDODM
Support: Bluetooth 4.0 above Phone Support: ios 11 or above and android 4.4 or above.
Language support: English APP name: LEDOOM
APP Connection Instructions:
Step One: Open APP and enter the RGB color setting.

Choose lighting colors on the color wheel and adjust brightness by dragging the slider bar below.

Lights will be connected automatically to the APP when the Bluetooth function is activated on your phone.
Enter shake mode oy mount, -Setting” button.

Step Two: Enter “mode’ for lighting modes and speed settings. Step Three: Enter the “Music’ set to play your favorite music, and lighting will dance with the music.
Step Four: Enter “Microphones setting, to choose either built-in Mk, which uses the microphone function on your phone to receive audio and change lighting colon accordingly; or external Mk, which uses the signal receiver to receive audio and things lighting colon accordingly.
Step Five: Enter ‘Timer” for lighting schedule setting;

If the Bluetooth connection Is not successful, check the possible causes by following the steps below.

1. Check if the connection of the lighting kit Is correct and If the lights function well.
2.  Check if the Bluetooth is activated.
3.  This lighting kit adopts the Bluetooth 4.0 version, which only supports connection with one phone. Check If the lighting kit has been paired to a phone. If yes, please disconnect it from the previous phone and pair it to yours.
4. Check if the Bluetooth Is successfully paired to the lighting kit. If not, exit the APP and restart it to connect the lighting kit again.
5. If the Blue-booth connection still fails after restarting the APP, please nit the APP and reboot your phone. Make sure the lighting kit is correctly wired and functions well, then open the APP to connect the lighting kit again.

Type B: 24-key Remote Controller

Type C: 4 Key RF Remote Control

A: ON/OFF
B: Music (4 modes)
C: Short press to circulate between 16 colors in static modes, long press for 2s each time to circulate between ten levels of brightness.
D: Short press to circulate between 22 dynamic modes, long press for as each time to circulate between ten levels of speed.
Note: When the remote control loses connection to the LED light, please pair It to the signal receiver of the light. How to pair? Once the light Is powered on In 2 seconds, point the remote controller to the signal receiver and long-press the power button on the controller for 5 seconds.

70 3010211579
10 0X140MM
1T6/10
CN1013

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>