Shenzhen Koto Electronics H2 Low Consumption Smart Wireless Doorbell User Guide

Low Consumption Smart Wireless Doorbell
Quick Guide
• Before using this produCtalease read the Quick Guide carefully and keep it for future reference V1.0

Package Contents

After opening the package, please check the camera( ‘The Device) to verify %%tether the following pails are complete.

Appearance

IR LED| In the event of inadequate ambient light, turn on the IR LED to increase the brightness
---|---
 Light Sensor| To collect the ambient brightness value, and when the illumination is than 2Lux, the infrared lamp is enabled.
Microphone| Used to collect ambient sound and record vocal dialogue.
 Call Button| Short-click can activate to inform users that someone is visiting and trigger a notification.
 PIR| When someone moves in front of the Device, PIR activates recording and sends a notification to the connected cell phone.
Lens|  Used to record images and video.
Indicator Light|   When the Blue Indicator Light is blinking, the Device is in the “Configuration” status. When the Red Indicator Light is always ON, the WiFi connection has failed. When the Blue Indicator Light is always ON, the device is successfully connected. When the Red and Blue Indicator Light are ON at the same time, the Device is not connected to WiFi. When the Red and Blue Indicator Light are OFF at the same time, the Device is OFF or STAND-BY.
Speaker|  Used to emit a prompting noise and support two-way conversation
Reset Button|  Long press 5 seconds to restore factory settings in working status
USB Interface| Used to charge the Device through the MicroUSB Interface.
 MicroSD card| MicroSD card slot. The maximum supported storage capacity is a 32Gb MicroSD card.
Battery| Two 18650 specification batteries are required, be
Compartment|  aware of negative and positive

Installation Guide

As shown by the following pictures, remove the rear panel.

1. Affix the bracket to the was by using the installation saws in the OCCOSSOry DOCk —CP (athrnahvely,urrecesal nage seekers cv • be used to arta to tempered data Or stainless Steel)
2. put the 18650 battery WO the berlerY COmPertmendnele me POSebe and name directions)
3. Press the reset button for S se cords. walled see for the 41010910r Ightlurn to red SION nosh (The device *odd be in vonckne condition. lore Press. sleep slate is irwalti)
4. Cover rte battery Id. design the device and my bracket. push dawn and leek me second saves to amuck, the nuanabon

Bracket ( Matching)
Step 1: Remove the backplane.
Operate as the paure shown please remove the backplane.
Step 2:Install the mounting plate to the wall.
Use the mounting screws snide the kit Mount the bracket on the wa1 (Or use 3M; hie on tempered (lass or stemless steel)
Step 3:Installation of machine mounting bracket:
Align and push down the damps of the equipment and fix the bracket. lock the antecksasserrely Sarti, and complete the instalLabon
Buzzer Matching(this device needs to be purchased separately)
Matching: Press and hold the buzzer volume key for S seconds. The LED Light will turn ON. Next. press the Boutell button wehn 5 seconds. When the buzzer LEO tanks quickly. the matching is complete.
Reset: Press and hold the bunt(‘ vaurne key for 10 seconds. The matching reset.

Equipment Connection

You can download the TuyaSmart app by searching for TuyaSmart in your app store or by scanning the following QRcode.

2. Registration, login, and password reset
1. Open the Tuya Smart app and tap Sign Up. In the User Agreement and Privacy Policy dialog box, carefully read the privacy policy and agreement and tap Agree to go to the account registration page.
2. Enter your mobile phone number or email address and tap Get Verification Code. The country or region on the registration page is the same as that you set in the mobile phone. You can also manually change the country or region before registration. 3. OntheEnter Verification Codepage,entertheverificationcode. OntheSet Password page set the password as per instructions and tap Done.
3. Login with your app account or a third-party account

1. OpentheTuyaSmartappifyouhaveregisteredanaccountintheTuyaSmart app, tap login. In the User Agreement and Privacy Policy dialog box, carefully read the privacy policy and agreement and tap Agree to go to the login page.
2. Check the country or region on the login page. The system automatically identifies your current country or region. You can also manually select a country or region.
3. Enter your registered mobile phone number or email address, enter the password, and then tap Login.
4. If you have installed WeChat or Tencent QQ on your mobile phone and have a WeChat or Tencent QQ account, tap the WeChat or Tencent QQ icon on the login page. On the authorization page that appears, allow authorized login for your WeChat or Tencent QQ account. If you use an iPhone, you can also log in with your Apple ID.
   

Reset password

If you forget your login password, you can reset the password based on the following process:

1. On the Log In page, tap ForgotPassword.

2. On the page that appears, check the country or region. The system automatically identifies the current country or region where you reside. You can also manually select a country or region. If your account is registered with a mobile phone number, the country or region must be the same as the one you selected during registration.

3. EnteryourregisteredmobilephonenumberoremailaddressandtapGet Verification Code.
   

4. On the Enter Verification Code page, enter the verification code.

5. On the page that appears, enter a new password and tap Done. Then the password is reset, and you automatically log in to the app.

6. For security concerns, the app will detect risks in your phone system during login. If the app detects a root or jailbreaking risk, a security reminder is- played. You can determine whether to exit the app or not. If no selection is made, the app will automatically exit.
   

5. Enter experience mode 1. Open the TuyaSmart app and tap Trynow. A dialog box appears, indicating that cloud storage, third-party voice control, and device sharing are not supported in the experience mode. 2. Tap Continue. The Home page appears.

ADD DEVICE

On the device list page, click the “Add Device” button in the center or dick the “+” button at the top right to enter the “Add Device” page, which is currently divided into two methods: “Manually Add” and “Automatically Discover”. (Use manual add mode)

ADD DEVICE MANUALLY- QR CODE PAIRING MODE

1. In addition to the Wi-Fi quick connection (default mode) and hotspot network configuration (compatible mode) that most devices have, some devices also have a “wired network configuration mode” (currently the device only supports QR code network configuration and WiFi fast even)

2. To use the QR code to configure the network, you need to set the indicator light of the IPC device to a fast flashing state or hear the corresponding prompt tone. 3. The reset steps can be viewed by clicking the “Try to configure network step by step” button.

4. After clicking Next, you will be taken to the page for entering the Wi-Fi password.
5. According to the prompts on the page, face the QR code directly to the camera and keep a distance of 15-20cm until you hear a prompt sound from the camera.
6. If you hear the prompt tone, please click the “Hear the prompt tone” button below to enter the page for adding devices.
7. If the network configuration fails, the following page will be displayed.

ADD DEVICE MANUALLY- WIFI FAST CONNECTION
1. To use WiFi quick connection, you need to set the indicator light of the IPC device to a fast flashing state or hear the corresponding prompt tone.
2. The reset steps can be viewed by clicking the “Try to configure network step by step” button.

3. Click Next, and you will be taken to the page for entering the Wi-Fi password
4. Click Next to enter the add device interface
5. If the network configuration fails, the following interface will be displayed
6. You can choose to switch the network distribution mode and use the QR code to configure the network

WARNINGS

1. The device is equipped with a rechargeable lithium battery. The battery life will be affected by the device’s wake-up times and the number of wake- ups. Therefore, the PIR sensor alarm detection function will be used when in an environment of a lot of people. It is recommended to turn off or set the device to low sensitivity to reduce device wake-up and call time then extend battery life. Please charge the battery immediately when the battery is low.
2. Put the device in the range of your router. Please make sure the network is normal in the installation environment and check whether the Wi-Fi is covered, especially installing outside the board/ door. If the Wi-Fi signal is weak, you need to select the relay setting or enhance the Wi-Fi relay improvement signal.

3. This device is a low-power intelligent product. It can support App remote wake-up, PIR wake-up, doorbell wake-up, and will enter sleep mode automatically for a short time after each wake-up. You can set up the work time in the App settings.
4. In mainland China the App couldn’t receive Google’s push messages. You need to turn on the App’s self-starting function to receive push messages. 5. This device provides free cloud storage and faces recognition services for one month. If you want to continue using these value-added services after the free trial period, you need to purchase in the App.

Technical Specification

Q &A

Q: Why can’ s the device connect to WIFI? A:

1. Please confirm that the WiFi connection adheres to the 2.4G protocol.
2. Confirm that the Red Indicator Light is blinking slowly.
3. Check whether the account name and password are correct and whether there are too many characters. Q: The Device is online, and there is a trigger event, but the cell phone does not receive any push notifications? A: Check whether the app has “Automatic Starting” activated and whether the “Application Authority” has the notification function enabled Disable “Battery Optimization” and “Close the app when in the background” and “Always On Display” (depending upon the situation, consider different optimization modes for different cell phone manufacturers). Q: What kinds of power supply modes are supported? A: 1. The Device can use the battery independently to work. 2. USB is available to charge the Device. Q: Does the Device support 3G? A: 3G cell phones are not supported, only is supported.

Introduction to Functions

LONG BATTERY LIFE: The capacity of the 18650 battery is 2600mAh, which equates to 6 months of battery life
HIGH DEFINITION: Million High Definition Pixels within the Ultra-Thin 1.7MM Lens
ANYWHERE, ANYTIME: Remote Cell phone activation(via the app)is supported
2.4G Wi-Fi connection supported
Clear two-way speaking
PIR supported. When someone is wandering out-doors, warning information is immediately sent to the connected cell phone via the app
Automatic switching between Day/Night mode, with clear pictures to safeguard you and your family members.

• Tip: There will be no further notice of any change of the above functions. Please take the actual object as the standard. Thanks! Warning Statement
  This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
  Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
  Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  -Reorient or relocate the receiving antenna.
  -Increase the separation between the equipment and receiver.
  -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet the general RF exposure requirements for a mobile devices. The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>