DELUXX 1000004656 Cinema Screen Slim Frame User Manual

DELUXX 1000004656 Cinema Screen Slim Frame

Hints

Read before construction and always follow the instructions.

• Please check ALL parts for completeness and damage before assembly. If parts are missing or damaged do not continue with the construction and contact the supplier with whom you purchased the screen or contact DELUXX directly.
• The screen may ONLY be constructed on soft, padded ground. The velor or powder coating and especially the projection fabric could otherwise be damaged.
• Do not touch the fabric with your greasy hands.
• The fabric must not be folded or kinked!
• Please do not write or paint on the fabric.
• No sharp objects must come into contact with the product, especially the fabric.
• The projection surface must never be cleaned with cleaning agents (especially nothing corrosive). Use mild (max 3%) soapy water.
• The velor frame requires special care and should not be cleaned wet. A fine brush or special nozzle on the vacuum cleaner may be used for cleaning.
• The screen may only be installed horizontally and level.
• The screen, especially the fabric must be kept away from fire and heat, otherwise, it can cause permanent damage.
• Please note the front and backside of the fabric before installation.
• Only install the screen on a load-bearing masonry wall and only with enclosed mounting brackets.
• Build the screen with 2 people and install on the wall with 2 people.
• Install the fabric with utmost care, it is very sensitive and kinking or folding the fabric leads to permanent damage.
• The product may not be installed by persons under 16 years or without the presence of an adult.
• Failure to comply with the above points may violate the product and warranty. You may permanently damage or impair the functionality of the screen. DELUXX assumes no responsibility if disregarded and the warranty will not stand.

In the box

• Aluminum velor cover (4x or 6x) Aluminum frame parts (4x or 6x)
• Projection Fabric (1x)
• Tension rods for fabric (4x or 6x)
• Corner connector incl. Screws for inner frame (4x) Corner connector incl. Screws for outer velor cover
• Wall bracket (2x or 3x)
• Screws and Rawl plugs for wall mounting
• Springs for fabric tension
• Tool for springs
• Screwdriver and Allen Key
• Connector for inner and outer frame (optional)
• Frame reinforcement with screws (optional)

Information:
6 parts are only included with larger screen sizes.

Assembly of the screen

Step 1
Slide the corner connectors of the inner frame into the short frame pieces, then slide them into the long frame pieces.
(If you have a 6 piece frame, prior to this step, use the connectors for the inner frame pieces)Before tightening the screws, make sure that the frame parts are as perfectly aligned as possible with no gaps at the corners and at absolute right-angles. Once you are happy, tighten the screws.

Step 2
Spread the fabric (face down) on a soft, clean and free of sharp objects) area and carefully push the rods into the outer pockets of the fabric. Make sure that the front of the fabric is pointing downwards.

Step 3
Carefully place the previously secured inner frame with 2 people, centered as well as possible on the projection fabric.

Start with one corner, using 4 springs, the fabric can be attached using the tension rods and springs. Use the clamping aid and carefully pull the springs around the frame and anchor the springs in the rear of the frame profile. The fabric is carefully drawn around the frame. This must be done with 2 people, one person anchors the fabric and a second person helps guide the fabric around the frame to avoid damage/deformation of the fabric. Now repeat the process with the other corners.

When the 4 corners are connected: Start on the long sides in the middle and anchor further springs working towards the edges. Then do the same (working from the middle to the edges) on the shorter sides of the frame.

(Before doing this, If you have a six piece frame,screw the two frame reinforcements to the long frame pieces on the rear of the frame.)

Step 4
Slide the outer (velor) frame pieces onto the screen and connect them with the corner connectors in all 4 corners. Screw the inner and outer frame together. If you hear a “click”, the frame parts are sufficiently connected.

Wall mounting

1. Depending on the width of your frame, bring the wall brackets to approximately 1/3 and 2/3 of the frame width on your wall. Use only load bearing masonry or solid wood walls for mounting. The wall brackets must be absolutely level (use spirit level and mark). Use only mounting material suitable for the wall material (eg dowels & screws for concrete or wood screws for solid wood). Mount the bracket to the wall.
2. Carefully lift the frame with 2 people at a time and place it onto the previously mounted wall brackets so that the upper frame profile attaches to the wall bracket. It should slip in and anchor into place. The installation of your screen is complete.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>