tp-link AX1500 Wi-Fi 6 Router Wireless User Guide
- June 6, 2024
- tp-link
Table of Contents
tp-link AX1500 Wi-Fi 6 Router Wireless User Guide
Packing list
- The device 1pc
- Power adapter 1 pc
- User guide 1pc
- Ethernet cable 1pc
If the above accessories are missing, please contact the customer service in official website for replacement
Product Overview
- Indicator light
- Reset (long press over 5 seconds)
- WPS Key(press within 5 seconds for WPS, 5 seconds above for mesh)
- LAN port : connect to computer, etc.
- WAN port : connect to modem, broadband modem, etc.
- Power port ( DC IN )
Indicator Led
Connect the Router
Configure the Router
- Open the mobile phone or computer browser, visit the http:// 192.168.10.1 website, enter the router management interface.
- Enter the default username and password on the label at the bottom of the router.
- After accessing the management interface, select the network mode- PPPOE, DHCP or Static IP to set according to the broadband you are using.
-
When selecting PPPOE, please enter the UserName and Password provided by the network operator, and click Apply
Ethernet WAN
This page is used to configure the parameters for Ethernet WAN.
-
When selecting DHCP, enter relevant information according to the prompts on the page, click Apply.
Ethernet WAN
This page is used to configure the parameters for Ethernet WAN.
-
When you choose “Fixed IP” to access the Internet, enter relevant information according to the prompts on the page and click “Apply”
Ethernet WAN
This page is used to configure the parameters for Ethernet WAN
Password Setting
In the router management interface of http:// 192.168.10.1, click Quick Setup interface to customize the WLAN (2.4GHz) / WLAN (5GHz) password. After setting the password, click Apply
WLAN Security Settings
This page allows you setup the WLAN security,Turn on WEP or WPA by using Encry
access to your wireless network.
EasyMesh Configuration
One-click Mesh function:
- Complete the configuration of the Controller, ensure that the Controller’s network is normal, and the green light is on.
- When additional Agent is needed: take out the new device and connect to the network, press the WPS button of the Controller and the Agent at the same time (for more than 5 seconds) for networking.
- Before networking, the indicator light of the Controller is on green (the network is normal), and the Agent is on red (the network is abnormal). In the process of networking, the indicator light of the Controller is on green flashing and the Agent is on red flashing. after the success of networking, the indicator light of the Controller is on green, and the indicator light of the Agent turns to green from red.
Mesh Setting
Setting the Controller: select WLAN –Easy Mesh in the router management
interface: fill Controller in Device Name; select Controller in Role; Click
the Apply button to save the Settings.
EasyMesh Interface Setup
This page is used to configure the parameters for EasyMesh feature of your
Access Point
Setting the Agent, in the router management interface of Agent, select WLAN -EasyMesh: fill Agent in Device Name; select Agent in Role; Click the Apply button to save the Settings.
After the two devices complete the above steps, the EasyMesh page will refresh and the Start PBC button will appear. Click Start PBC for both devices, or press the WPS button shortly, automatic mesh network can be triggered.
Frequently Asked Questions
What to do if there is a problem when setting the router to surf the Internet ?
- If you cannot find the router’s SSID on your mobile phone, please make sure that the router is powered on, wait for a moment and wait for the router to finish start-up, and then search again on your mobile phone to connect.
- If the device cannot connect to the network, please ensure that the network port connection of the router is not loose, no poor contact, and no abnormal network cable.
How to restore the router to factory settings ?
- Power on the router and wait for a moment until the router finish start-up. Press the RESET hole of the router with a needle for more than 5 seconds. After the indicator light goes out, release it. After the red light is turned on when the router restarts, the factory setting restoration has been completed. After the factory settings are restored, the router needs to be reconfigured.
What should be paid attention to during the setting of EasyMesh ?
- After the completion of EasyMesh networking, the Controller will synchronize its SSID, password and channels of 2.4GHz and 5GHz to the Agent.
- After modifying the SSID, password and channel on the Controller, the Controller will synchronize these configurations to all Agents. If the above information is modified on the Agent , it will not synchronize to other devices.
- After the power failure, the routers will resume the original EasyMesh network by default, and there is no need to reset.
- If the EasyMesh network of the Controller is closed, the whole network will be dissolved; If the EasyMesh network of the Agent is turned off, the device is disconnected from the mesh network alone
Security Issues
- Before using and operating the router, please read and observe the following notes to ensure the stable performance of the router and to avoid dangerous or illegal situations.
- Please use and store the router and its accessories within the temperature range of 0℃~40℃. When the temperature is too high or too low, it may cause equipment failure.
- In the process of using the router, ensure that the distance between the human body and the antenna of the router is more than 20cm.
- Only use accessories approved by the router manufacturer and compatible with this type of router. If other types of accessories are used, it may violate the warranty of the router and the relevant regulations of the country where the equipment is located, and may lead to safety incidents.
- Power sockets shall be installed near the router and shall be easily accessible.
- When the device is not in use, disconnect the power from the router and unplug the power plug from the power socket.
- Do not dispose of the equipment and its accessories as ordinary household waste.
FCC Warning Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help important announcement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance of 15cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>