Wanma Soaring Electronic Technology C007 Traffic Alarm User Manual
- June 6, 2024
- Wanma Soaring Electronic Technology
Table of Contents
User Manual
TRAFFIC ALARM
C007
Precautions
Due to the different heat insulation and explosion-proof films on the front glass of the car, it may take about 1-5 minutes to successfully locate the device for the first use. When passing through confined spaces such as tunnels, underground parking lots, or high-rise urban areas, there will be no voice announcements due to weak GPS signals, and the equipment will return to normal after leaving the above areas.
Installation and operation
This product can be mounted on the glass or in the center console of the car.
3M double-sided tape can be pasted on the side printed with BD+GPS. The
sticking position should avoid the lens of the dashcam as much as possible to
avoid interference with satellite reception and ensure the strength of the
satellite signal.(Specific steps are as follows)
1. When using as a dashcam partner, unplug the power cord of the dashcam from
the socket and insert it into the DC-5V port of this product ( see ① below),
and plug the mini to micro cable in the accessory kit To the 5V voltage input
of your dashcam, plug the other end into the other DC-5V port of the device
(see ② below).
2. When used alone as a GPS voice alert, connect the power cord to the car
cigarette lighter (voltage 5V) and connect the other end directly to the
device’s port (see figure on the next page). 
When you turn on the power, you will hear the ringtone (When using it for the first time, it takes 1 to 5 minutes to search the satellite signal). After that, the device works properly.
Button function
This product uses a convenient single-button operation mode. It will start
automatically when you turn on the product. 【Press and hold】 the button for
about 3 seconds to
enter the data upgrade state. 【Press】 the button to adjust the volume. When
the volume is at its maximum, press the button once to turn it down. You can
choose from eight levels of volume.
Data upgrade
1. Bluetooth connection to a mobile phone: Scan the QR code to download the
mobile app (only for Android phones for the time being) and follow the
instructions on the page. Download URL:
gsm.wanmagps.com/update/sopft.apk
http://gsm.wanmagps.com/update/soft.apk
2. Connect the device to your computer using a USB cable (the computer must
be connected to the network). Then a window will pop up on your computer and
you can click Update to update the data.
Troubleshooting
-
Unable to power the device
① Make sure that the charging port of the car works properly.
② If the device is connected with a dashcam, check that the power of the dashcam is turned on normally. -
Continuous anomaly warning
① Turn off the power and restart or re-upgrade data;
② Check if the device is damaged. -
Slow satellite connection
① Check if there are any skyscrapers or trees around.
② It takes 1 to 5 minutes to search for satellites for the first time.
③ Start after leaving the underground or tunnel or wait a few minutes until satellite positioning is completed. -
No voice prompt for speed camera spot
① Download the latest fixed photo spot data.
② Register a VIP account, report the location online and add fixed pot data.
③ Contact after-sales service and report the location of the failure. -
A GPS device is down
① Record the location of the downtime.
② Connect to the computer and upgrade the database software again.
③ Please report to the product seller.
If you have any questions, please contact us at service@spedaltech.com
For more information, please scan the QR code on the right side to visit our homepage and read the detailed manual.
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>