Legget Platt 292-0076-A Remote Control Instruction Manual
- June 14, 2024
- Legget Platt
Table of Contents
Legget Platt 292-0076-A Remote Control
REMOTE CONTROL FUNCTION
NOTE: REMOTE CONTROL REQUIRES (2) AAA SIZE BATTERIES. TO CONSERVE BATTERY LIFE, THE TRANSMITTER TURNS OFF ALL FUNCTIONS WHEN ANY BUTTON IS PRESSED FOR MORE THAN 50 SECONDS.
PRESS & HOLD” MODE: To put the remote control in “press and hold” mode simultaneously press and hold the FLAT and FLASHLIGHT buttons for 3 seconds. The remote backlight will flash 3 times, confirming the change. Your base is now set to “Press & Hold” mode.
PRESS & RELEASE” MODE
To revert back to “press and release” mode, simultaneously press and hold
the LOCK and FLASHLIGHT buttons for 3 seconds. The remote backlight will flash
once, confirming the change. Your base is now set to “Press and Release” mode.
NOTE: THIS ACTION WILL ALSO RESET MEMORY POSITIONS TO FACTORY DEFAULT SETTINGS.
REMOTE CONTROL PROGRAMMING
- Simultaneously press and hold the HEAD UP and FOOT DOWN buttons on the remote control until the remote control backlight flashes, then release.
- Unplug the base from the power outlet. Wait 3 minutes, then plug the base back into a power outlet. YOU HAVE 1 MINUTE TO COMPLETE PROGRAMMING PROCEDURE
- Simultaneously press and hold the HEAD DOWN and FOOT UP buttons on the remote control until the remote control backlight flashes, then release
- Operate the remote control to verify the base functions correctly.
REMOTE CONTROL PROGRAMMING
-
Plug both bases into a power outlet. Operate each base to verify the base functions properly.
Lower both bases to the flat position.
NOTE: IF BASES DO NOT RESPOND, REVERT BACK TO 1-TO-1 PROGRAMMING (SEE SECTION ABOVE). -
UNPLUG both bases. Place both bases on their sides close to each other.
CAUTION: DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASE -
Plug one end of the sync cable into the sync port (on the control box) of base 1. Plug the other end of the sync cable into the sync port (on the control box) of base 2.
-
Turn both bases over onto their legs.
CAUTION: MAKE SURE THE SYNC CABLE IS NOT CAUGHT IN BASE OR PINCH POINTS. -
Plug both bases back into the power outlet
-
Operate the remote control(s) to verify both bases function correctly. If using only one remote control to operate both bases, store the second remote for use as a spare.
NOTE: TO REVERT BACK TO 1-TO-1 PROGRAMMING, REMOVE THE SYNC CABLE FROM THE CONTROL BOXES.
POWER DOWN OPERATION
Your adjustable base, depending on the model purchased, may have the following feature. Use this procedure to lower the base to flat during a power outage. Do NOT put batteries in the power-down device until necessary for use.
- Insert (2) 9-volt alkaline batteries into the power brick.
- Press the FLAT BUTTON on the remote control or in-line switch (if equipped) to adjust the base to the level position.
- Remove batteries from the power brick and discard. When power is restored from an outage, the base is ready to resume normal operation.
TROUBLESHOOTING
If the adjustable base fails to operate, investigate the symptoms and possible solutions provided in the chart below:
| SYMPTOM | SOLUTION |
|---|
No features of the base will activate.
| • Program the remote control (see Remote Control Programming section of this manual for
programming procedures).
• Unplug the power cord, wait 30 seconds, and plug in to reset electronic components.
• The electrical circuit breaker may be tripped. Check the electrical service breaker box to verify.
• Defective surge protection device or electrical outlet. Test the outlet by plugging in another working appliance.
• If the base was operated over the rated duty cycle, the thermal switch opens. Wait 30 minutes before trying to operate the base. Once the base resumes normal operation, do not exceed the duty cycle.
The remote control backlight does not illuminate.| • Replace batteries in
the remote control.
The head or foot section will elevate, but will not
return to the horizontal (flat) position.
| • Base mechanism may be obstructed. Elevate the base and check for obstruction. Remove obstruction.
Excessive motor noise.
| • The head section may be too close to the wall.
• If the base is located on hard surface flooring, place carpet pieces or rubber caster cups under
each leg or caster of the base.
• Elevate the head or foot section a short distance (with the remote control) to realign the lift
lower mechanisms with the base support platform.
• Verify that the base is not positioned against a wall, nightstand, or other object that may cause vibration or noise.
• If the base is installed over a base frame, verify motors are not causing the base frame (or base
frame components) to vibrate.
ADVISORY
IMPORTANT INFORMATION
READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT
WARNING: FOR OPTIMUM ADJUSTABLE BASE OPERATION, USE A GROUNDED, ELECTRICAL SURGE PROTECTION DEVICE (NOT INCLUDED). FAILURE TO USE A SURGE PROTECTION DEVICE COULD COMPROMISE SAFETY OR CAUSE PRODUCT MALFUNCTION.
ELECTRICAL RATING
Input: 100-240VAC, 50/60Hz, 1.6A. Output: 29VDC, 2A.
ELECTRICAL GROUNDING
This product is equipped with a polarized or grounded electrical power cord.
The power cord will only fit into a grounded, electrical surge protection
device (not included) or a grounded electrical outlet.
WARRANTY
WARRANTY WARNING
Do not open any control boxes, motors, or remote control devices (with the
exception of the remote control and power-down box battery compartments). The
product warranty will be void if these components are tampered with. Do not
attempt to alter component wiring or adjust or modify the structure of the
product in any way or the warranty will be void. Any repair or replacement of
base parts must be performed by authorized personnel
LUBRICATION
This product is designed to be maintenance-free. The lift motors are
permanently lubricated and sealed—no additional lubrication is required. Do
not apply lubricant to lift motor lead screws or any nylon nuts or the base
may inadvertently creep downward from the elevated position.
LOCATION ENVIRONMENT
The level of sound experienced during operation is directly related to the
location environment.
SERVICE REQUIREMENTS
Service technicians are not responsible for moving furniture, removing
headboards and footboards or any items required to perform maintenance on the
base. In the event the technician is unable to perform service due to lack of
accessibility, the service call will be billed to the purchaser and the
service will have to be rescheduled.
PRODUCT RATINGS
The base lift motors are not designed for continuous use. Reliable operation
and full life expectancy will be realized as long as the lift motor operation
does not exceed two (2) minutes over a twenty (20) minute period or
approximately 10% duty cycle. Note: Massage-equipped bases are not designed
for continuous, extended massage operation. Massage systems are rated for a
maximum of 2 hours of use within any 6-hour period. Any attempt to circumvent
or exceed product ratings will shorten the life expectancy of the product and
may void the warranty.
The recommended maximum weight (including mattress) is 850 lb (385 kg) distributed evenly across the base. This product is not designed to support or lift this amount in the head or foot sections alone. Note: Exceeding the recommended weight restrictions could damage the base and void the warranty.
For best performance, consumers should enter and exit the adjustable base with the base in the flat (horizontal) position. Avoid placing the entire weight on the head or foot section of the base, including when in the raised position. DO NOT STAND ON BASE AT ANY TIME
- UL (Underwriters Laboratories) recognized components.
- CFR 1633 is approved for use with most mattresses.
SMALL CHILDREN / PETS WARNING
After the base is unboxed, immediately dispose of packaging material as it can
smother small children and pets. To avoid injury, children or pets should not
be allowed to play under or on the base. Children should not operate this base
without adult supervision.
HOSPITAL USE DISCLAIMER
This base is designed for in-home use only. It is not approved for hospital
use and does not comply with hospital standards. Do not use this base with
tent-type oxygen therapy equipment, or use it near explosive gases. The
manufacturer makes no representation or warranty that the adjustable base
constitutes a medical device or is suitable for medical or therapeutic use.
PACEMAKER WARNING
This product produces a vibrating sensation. It is possible that individuals
with heart-assist pacemakers may experience a sensation similar to exercise.
Consult the physician for complete information.
MASSAGE OPERATION
The massage feature will emit a minimal tone during operation. This is normal.
When the massage level is increased, motor resonance will intensify
accordingly.
LIFTING/LOWERING MECHANISMS
The lift/lower feature will emit a minimal humming sound during operation.
This is normal. If excessive noise or vibration is experienced, reverse the
movement action (up or down) of the base with the remote control. This should
realign the base’s activating mechanisms to the proper operational position.
FCC COMPLIANCE
The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
Radio Frequency = 2.4GHz.
© 2022 Leggett & Platt, Inc. Adjustable Bed Group