SNAIGE RF62FB-TNCBNE0 Refrigerator Freezer User Manual

SNAIGE RF62FB-TNCBNE0 Refrigerator Freezer logo

Dear Customer,
Some provisions in this user manual are unified for refrigerating products of different types (for a refrigerator, refrigerator-freezer or freezer). CAREFULLY READ THE INSTRUCTION MANUAL.
The Manufacturer shall not be held liable for damage arising from the failure to observe the instructions contained in this manual.
Keep this manual for future reference, or to pass it over to the next user.

General information:
The appliance is a refrigerator freezer. The appliance is equipped with a frost-free refrigeration system (“No Frost”).
The refrigerator compartment is designed for the brief storage of fresh food. In the refrigerator compartment is the cold section. A temperature of -2 to +3 °C is maintained in the cold section which is suitable for short-term storage of meat, fish, and similar products.
The freezer compartment is designed for the freezing and long-term storage of food products.
This appliance is intended to be used in households and similar applications. This appliance is not for professional use. Don’t use the appliance outdooT

GUIDELINES CONCERNING THE SAFETY OF USE

General safety requirements:

• WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.
• WARNING: Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• WARNING: Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
•  WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
•  WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the appliance.
• WARNING: Disposal of the appliance should be according to national rules.

WARNING: Do not damage the appliance refrigeration system. It contains the refrigerant gas R600a. If the refrigeration system is damaged:

•  Do not use any open flame.
• Avoid sparks-do do not turn on any electrical appliances or lighting fixtures.
•  Immediately ventilate the room: air the room in which the appliance is placed for a few minutes (the size of the room for a product containing isobutane /R600a must be at least 4 m3) to avoid damage to the cooling system.
  C- Pentane is used as a blowing agent in insulation foam and it is a flammable gas.
  – The appliance should be used only for freezing and storing foodstuffs.
  – This appliance is not designed for the storage of explosive substances such as aerosol cans with a flammable propellant.
  – It is prohibited to store petrol and other flammable liquids near the appliance.

Children and vulnerable people safety:

– Do not allow children to play with the appliance or to plug it in or unplug from the electricity supply socket. Do not allow children to play with the packaging material from the appliance. Cleaning and user maintenance shall not be made by children without supervision
– This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children aged from 3 to 8 years are allowed to load and unload refrigerating appliances.

Requirements for the connection to the mains:

The appliance should only be connected to an earthed socket installed in

accordance with the regulations. Make sure that the supply voltage corresponds with the voltage marked on the rating label. This product complies with all binding CE labeling directives. The earthed electrical socket by which the appliance is connected to the mains should be in an accessible place. The appliance must be earthed in conformity with national electrical safety standards. The manufacturer will not be held liable for any damage or injury which may result from the failure to fulfill this requirement.

– To avoid the exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by a qualified personnel and with a cable of the same type.
– It is forbidden to readjust or modify any parts of the unit. It is crucial not to damage the capillary tube visible in the compressor recess. The tube may not be bent, straightened or wound. If the capillary tube is damaged by the user the guarantee will be void.
– Do not use adapters, multiple sockets and two-wire extension leads. If it is necessary to use the extension lead, it must be equipped with a protection ring and a single socket and must have a VDE/GS safety certificate. If an extension lead is used (with a protection ring and safety certificate), its socket must be located at a safe distance, away from the sinks, and must not be in a place where it could be flooded by water or wastewater .
– When positioning the appliance, be careful that the electrical cord isn’t squeezed in order to avoid its damage. Do not store heavy objects such as cooling devices, furniture or other domestic devices next the appliance in such a way that they could squeeze and damage the electrical cord. This can cause a short circuit and a fire.
– Make sure that the plug of the electrical cord is not squeezed by the back wall of the appliance or otherwise damaged. A damaged plug can be the cause of a fire!

Do not try repair the appliance on your own. Always contact an authorized technician. To avoid the exposure to danger, always have faulty cable be replaced only by the manufacturer, by our customer service or by qualified person whit a cable of the same type.

ATTENTION! Do not remove the cover of the light-emitting diode (LED) luminaire! If the cooling appliance is equipped with light-emitting diode (LED) luminaire and the lighting is not functioning, please contact a maintenance technician to have it replaced. The luminaire can be replaced only by a maintenance technician!

Requirements for safe use:

– It is forbidden to use a technically damaged appliance.
– If the appliance is unplugged (for cleaning, moving to another place, etc.), it may be repeatedly switched on after 10 min.. This is to allow the oil to flow back in the compressor
– Do not put frozen products, taken out directly from the freezer (lollies, ice cubes, etc.) into your mouth; their low temperature may cause severe frost-bite.

– When performing activities, such as cleaning, maintenance or moving, the appliance must be completely disconnected from power supply (by pulling the plug out from the socket). Do not pull on the cord, but hold the body of the plug instead.
– Do not place heavy objects on the top of the freezer
– Do not place any switched-on electrical devices on top of the appliance.
– Do not place any dishes with liquids on top of the appliance and do not keep flowers in vases or other liquid-filled vessels on the appliance.
– Do not climb on or sit on the appliance, do not lean on or hang on the appliance doors and do not allow children to do this..
– Do not remove or touch items from the freezer compartment if your hands are wet or damp.
– Do not use water spray and steam to clean the appliance.

The manufacturer guarantees reliable operation of the refrigerator when the relative air humidity not greater than 70 percent and the ambient temperature is:

+ 10 TO +32 DEGREES CELSIUS – the appliance climate class is SN;
+ 16 TO +32 DEGREES CELSIUS – the appliance climate class is SN;
+ 16 TO +38 DEGREES CELSIUS – the appliance climate class is ST.
+ 16 TO +43 DEGREES CELSIUS – the appliance climate class is T.

INSTALLATION AND OPERATING CONDITIONS

Positioning

The appliance operates properly at the ambient temperature (see product fiche). Do not use it in the cellar, unheated summer cottage during autumn and winter. Place the appliance in a dry, well-ventilated room.

• WARNING! The appliance should not be operated in an unheated room or porch. Place the appliance away from heat sources such as kitchen stove/oven, radiators, or direct sunlight. The appliance must not touch any pipes for heating, gas or water supply, or any other electrical devices.
  The refrigerator adopts 220~240V/50Hz AC power.

•  Do not cover the ventilation holes at the top of the appliances – it must be good air circulation around the appliance, there should be a gap of at least 10 cm between the top of the appliance body and any furniture that may be above it (see page 2, picture 2). If this requirement is not followed, the appliance consumes more electrical energy and its compressor may overheat.

•  The appliance must stand on a level surface and must not touch the wall. If necessary, regulate the height of the appliance by adjusting the leveling feet: by turning them clockwise – the front of the appliance rises, by turning them counterclockwise – it comes down.

Preparing the appliance for operation:

t is recommended to prepare the appliance for operation with a helper.

•  When moving, do not make excessive pressure to the door or top cover, otherwise deformation will occur.
• Do not turn upside, horizontally place or vibrate the refrigerator, the carrying angle can not be greater than 45°. Please hold the door and hinge when moving.
• When positioning the appliance in chosen location, it will move more easily into position if you lift the front a little and incline it backward (less than 20°), allowing it to roll on its casters.
• Be careful not to damage the floors (e.g.parquet) when moving the appliance. Install the appliance on a floor or support strong enough to take its weight and in a place suitable for its size and use.
•  Before use, remove all packing materials, including bottom cushions, foam pads and tapes inside of the

The appliance should not be connected to the mains until all packing and transport materials aren’t removed. Suitably dispose the packaging material.

First use:

• Before using the appliance for the first time, the interior and all internal accessories should be washed with lukewarm water and some neutral soap to remove the typical smell of a brand-new product, then dried thoroughly.

Wait at least 4 hours before connecting the appliance to the power supply.

This is to allow the oil to flow back in the compressor

• When first starting up or after a period out of use, before putting the products in the compartment let the appliance run at least 2-3 hours.

The appliance shall run continuously once it is started. Generally, the operation of the appliance shall not be interrupted; otherwise, the service life may be impaired.

DESCRIPTION OF THE APPLIANCE: . see pages 1, fig. 1

THE APPLIANCE ACCESSORIES LISTED BELOW MAY DIFFER FROM THE ACCESSORIES OF THE APPLIANCE YOU HAVE BOUGHT IN QUANTITY AND IN DESIGN. This description is adapted for the entire group of two-compartment refrigerator-freezer combinations.

1 Shelf

2 Cold section drawer

3 Fruit and vegetable

4 Freezer section drawers

5 The front leveling feet

6 door trays

ELECTRONIC CONTROL PANEL DESCRIPTION

RF62FB-TNCBNE0 RF59FB-TNCBNE0 RF59FB-TN00NE0

The display panel is designed on the fridge door, the pattern of which is displayed as the right Figure.

When the refrigerator system is connected to the power supply for the first time, all icons on the display panel gets illuminated for 2s, and the system runs in the Smart ECO mode by default

When all the doors are closed, the display gets extinguished automatically if no key operation within 3 minutes. When the display is off, it will light up if any door is opened or any key is pressed.

The following key operations are valid only when the keys are unlocked and gets
illuminated on the display.

Temperature setting

Fridge temperature setting:

• Press the Fridge key to select the fridge zone, with the corresponding icon flickering, and then
• Press the key 6 to adjust the temperature, finally press the OK or wait for 5s to validate the above temperature setting.
• The fridge temperature setting cycles as follows: 5→6→7→8→OFF→2→3→4→5；
• OFF refers to Fridge Off, and when OFF takes effect, the fridge will stop cooling. NOTE: Take foods out of the fridge compartment before setting this function.
• Freezer temperature setting:
• Press the Freezer key to select the freezer zone, with the corresponding icon flickering, and then press key 7 to adjust the temperature, finally press the OK or wait for 5s to validate the above temperature setting.
• The freezer temperature setting cycles as follows:
  -18→-17→-16→-24→-23→-22→-21→-20→-19→-18v

Smart ECO

• Smart ECO
  When the Smart ECO function is enabled, the temperature of the fridge compartment is controlled at +4℃, and that of the freezer compartment at – 18℃, so that foods can be stored in the best condition while the refrigerator is running more efficiently and with better performance.
  Under the Smart ECO mode, the fresh food compartment temperature and the freezer compartment temperature are subject to no change.

• Enabling the Smart ECO function:
  Press the Function key to select Smart ECO until the corresponding icon 5 gets flickering, and then press the OK key within 5s for confirmation. If the OK is not pressed within 5s, the setting will be invalidated.

• Exiting the Smart ECO function:
  Under the Smart ECO mode, press the Function key to select Smart ECO until the corresponding icon 5 gets flickering, and then press the Okey for confirmation. The Smart ECO function will get excited.
  NOTE: When the Vacation or Fast Freezing or Fast Cooling function is enabled, the Smart ECO function will be disabled automatically.

Fast Cooling

When this function is enabled, the fridge temperature is automatically set at +2℃, with the temperature reduced in a rapid manner, so that foods can be kept in fresh condition with their nutrition not lost.
Under the Fast Cooling mode, the fridge temperature is subject to no adjustment.
Enabling the Fast Cooling function:
Press the Function key to select Fast Cooling until the corresponding icon 2 gets flickering, and then press the OK key within 5s for confirmation. If the OK is not pressed within 5s, the setting will be invalidated.
Exiting the Fast Cooling function:
Under the Fast Cooling mode, press the Function key to select Fast Cooling until the corresponding icon 2 gets flickering, and then press the OK key for confirmation. The Fast Cooling function will get exited.
NOTE: When the Vacation or Smart ECO function is enabled, the Fast Cooling function will be disabled automatically.

Fast Freezing

When the Fast Freezing function is enabled, the freezer temperature will be controlled at -32℃automatically, and after 26 hours of running, the Fast Freezing function gets exited. Cooling down the freezer temperature in a rapid manner is beneficial to the prevention of food nutrition against lost and the preservation of freshness.
Under the Fast-Freezing mode, the freezer temperature is subjected to no adjustment.
Enabling the Fast-Freezing functio n:
Press the Function key to select Fast Freezing until the corresponding icon 3 gets flickering, and then press the OK key within 5s for confirmation. If the OK key is not pressed within 5s, the setting will be invalidated.

Exiting the Fast-Freezing function:
NOTE: After a cumulative running period of 26 hours, the Fast Freeze function will exit automatically.
Under the Fast Freezing mode, press the Function key to select Fast Freezing until the corresponding icon 3 gets flickering, and then press the OKkey for confirmation, the Fast Freezing function will get exited.
NOTE: When the Smart ECO function is enabled, the Fast-Freezing function will be disabled automatically.

Vacation

When the Vacation function is enabled, the freezer temperature will be controlled at +14℃. When you are out for a quite long time, you can set the Vacation function to keep the refrigerator running with low energy consumption, while ensuring the fresh food compartment is free from undesirable smell and the freezer compartment operates normally.
NOTE : Be sure to take out all foods from the fresh food compartment before setting this function.
Under the Vacation mode, the fridge temperature is subject to no change.
Enabling the Vacation function:
Press the Function key to select Vacation until the corresponding icon 4 gets flickering, and then press the OK key within 5s for confirmation. If the OK is not pressed within 5s, the setting will be invalidated.
Exiting the Vacation function:
Under the Vacation mode, press the Function key to select Vacation until the corresponding icon 4 gets flickering, and then press the OK key for confirmation. The Vacation function will get exited.
NOTE : When the Smart ECO or Fast Cooling function is enabled, the Vacation function will be disabled automatically

Power cut memory

In case of power failure, the refrigerator will maintain the operating state before power failure when power supply is restored

Power-on delay.

In order to protect the refrigerator compressor from being damaged in the case of short-time power failure (i.e., less than 5 minutes), the compressor will not be started immediately after it is powered on.

Over-temperature alarm (only after power outage).

When the refrigerator system is powered on, if the freezer sensor temperature is higher than -10℃, digits of the freezer zone get flickering on the display. The freezer temperature can be displayed when any key is pressed, and the normal display will be restored when any key is pressed again or after 10s.

Door open alarm.

If the fridge door is open for more than 3 minutes, buzzer alarms will be continuously issued, which can be stopped when any key is pressed, but will be restored after 3 minutes if the door keeps open. The alarms will not be lifted until the door is closed.

Fault alarm.

In case E0,E1,E2,EH, or EC is displayed on the operation panel, it indicates fault with the refrigerator. Please contact the aftersales person for visiting service in such case.

Adjustment of the fridge air regulating lever.

The cool air entering the fresh food storage compartment will gradually increase as the air regulating lever is adjusted from the MIN. to MAX position.

RF59FG-TN00NF0

When the refrigerator system is powered on for the first time, all icons on the display panel gets illuminated for 2s, and the system runs at +4℃ by default.

Temperature setting

Fridge temperature setting on the display panel (Modes 2, 4, 5, 6 and 8)

Operating environment| Suggested Mode(s)| Method
In summer (higher than +35℃)| 4，5, 6，8| ****

Press the “SET “key

for adjustment.

Normal condition| 4, 5
In winter (lower than +13℃)| 2，4
When foods need to be cool fast.| Fast Cool

Temperature can be adjusted by pressing the ‘SET’ key. Every time when the “SET” key is pressed, the current mode indicator lights off while the next mode indicator lights up, with the said mode setting validated if no key operation within 5s (or else, the mode setting will be invalid). After the setting takes effect, the temperature will be immediately controlled as per the mode setting.
The temperature modes cycle as following: “2→4→5→6→8→FAST COOL→2”

Fast Cool:
Cooling down the temperature in a rapid manner is beneficial to the prevention of food nutrition against lost and the preservation of freshness.
After a cumulative running period of 30 hours, the fast cooling function will exit automatically, with the temperature mode restored to that set before the fast cooling function is enabled

Freezer temperature setting by air regulating lever

Position| Freezer temp.| TIPS
MAX| The cooling air supply is maximum, with the freezer temperature decreased.| Usually, the air regulation level is adjusted in the middle position
MIN| The cooling air supply is minimum, with the freezer temperature increased.

Estimate the amount of foods to be frozen up. When freezing large amounts of fresh food, adjust the temperature control knob to the low mode, with the freezer temperature lowered.

Door open alarm.

When the fridge door keeps open for more than 3 minutes, the buzzer starts issuing alarms, which can be suspended for 3 minutes by pressing any key, but they will not be stopped until the said door gets closed.

Power cut memory.

In case of power failure, the refrigerator will maintain the operating state before power failure when the power supply is restored.

Power-on delay.

In order to protect the refrigerator compressor from being damaged in the case of short-time power failure (i.e., less than 5 minutes), the compressor will not be started immediately after it is powered on.

Fault alarm.

When the indicator light of Mode 2 or Mode 5 keeps flashing, it indicates a fault with the refrigerator. Please contact the aftersales person for visiting service in such case.

INSTRUCTIONS FOR FOOD STORAGE

• To avoid contamination of food, please respect the following instructions:
  – Opening the door for long periods can cause a significant increase of the temperature in the compartments of the appliance.
  – Clean regularly surfaces that can come in contact with food and accessible drainage systems.
  – Store raw meat and fish in suitable containers in the refrigerator, so that it is not in contact with or drip onto other food.
  – If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mold from developing within the appliance.

•  The appliance storage bin should not be lined with aluminum foil, wax paper, or paper toweling. Liners interfere with cold air circulation, making the appliance less efficient.

• You’d better clean the foods and wipe them dry before storing them inside the refrigerator. Before foods are put in the refrigerator, it is advisable to seal them up, so as to prevent water evaporation to keep fresh fruits and vegetables on one hand and prevent taint of odor on the other hand.

• Do not put too many or too-weight foods inside the refrigerator. Keep enough space between foods; if too close, the cold airflow will be blocked, thus affecting the refrigeration effect. Do not store excessive or overweight foods, to avoid the shelf from being crushed. When storing the foods, keep a distance away from the inner wall; and do not place the water-rich foods too close to the fridge rear wall, lest they get frozen on the inner wall.

•  Categorized storage of foods：Foods should be stored by category, with the foods you eat every day placed in front of the shelf so that the door open duration can be shortened and food spoilage due to expiration can be avoided.

Cold section drawer.

In the case of refrigerating appliances with cold section, a statement to the effect that some types of fresh vegetables and fruits are sensitive to cold and therefore are not suitable for storage in this kind of compartment should be made.

The freezer temperature is controlled below -18 ℃, and it is advisable to store
the food for long-term preservation in the freezer compartment, but the storage
duration indicated on the food packaging should be adhered to.

• Hot food should be put into the appliance chamber after it cools down to room temperature.
• DO NOT EXCEED THE MAXIMUM AMOUNT OF FROZEN FOOD INDICATED IN THE PRODUCT FICHE.
•  Do not refreeze partly thawed products.
• Do not place unwrapped foodstuffs in the freezer sections.
•  Fresh food for freezing should not touch already frozen foodstuffs.
• Do not freeze foodstuffs that are warmer than the room temperature.
• WARNING! Do not freeze liquid foodstuffs in glass vessels or bottles.
•  Do not consume ice made in the freezer compartment straight away.
•  Products will freeze more quickly if they are divided up and packed in small portions.
• Strictly observe the foodstuff validity time indicated by the manufacturer on the product packaging.
• Do not consume ice made in the freezer compartment straight away.
• Products will freeze more quickly if they are divided up and packed in small portions.

CAUTION! In the event of accidental defrosting, for example due to a power failure, if
the power has been off for longer than the value shown in the technical characteristics
chart under “rising time”, the defrosted food must be consumed quickly or cooked
immediately and then refrozen (after cooling).

Fast freezing

(RF62FB-TNCBNE0, RF59FB-TNCBNE0, RF59FB-TN00NE0). Refer to the
description about fast freezing function in the ELECTRONIC CONTROL PANEL
DESCRIPTION section.

DEFROSTING, CLEANING AND CARE

REFRIGERATOR – FREEZER GETS DEFROSTED AUTOMATICALLY: it operates a frostfree
cooling system (No Frost). However, according to how often the freezer door were
opened and closed, and to – how warm products were placed into the appliance, the
frost can accumulate on walls of the freezer inner liner and drawers. It is normal. But the
thicker is the layer of frost, the higher is power consumption. In case if No Frost
system had not managed to evaporate the excess moisture and the frost layer has
formed on, you should defrost the appliance. To defrost the appliance, follow the steps
in sequence:

•  WARNING! Turn the appliance off and pull the plug out of the electrical socket.
•  Remove foodstuffs from the freezer compartment. The frozen foodstuffs will not warm up too much while you are thawing the freezer compartment if you cover them with athick cloth and keep them in a cool place.
•  Leave the door of freezer compartment open. When the frost melts, clean and wipe dry the surfaces and fixtures of the freezer compartment.
•  Close the appliance door. Plugin and turn on the appliance.

Before cleaning the cooling device and its rear compartment part, the

device must be disconnected from the mains by unplugging..

Regularly clean the hermetic gaskets of the doors. Wipe dry.

•  Do not use hard brushes, clean steel balls, wire brushes, abrasives, such as toothpaste, organic solvents (such as alcohol, acetone, banana oil, etc.), boiling water, acid or alkaline items clean appliance considering that this damage the freezer surface and interior.
•  Do not rinse with water so as not to affect the electrical insulation properties. Please use a dry cloth when cleaning temperature control knob and electrical components.
• How to disassemble the parts. If the refrigerating appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mold from developing within the appliance.

How to disassemble the parts.

Fridge door bottle rack:
Hold the bottle rack with both hands, and then push it up.

Fridge shelf:
Hold one end of the shelf, and lift it up while pulling it outwards.

ENVIRONMENTAL PROTECTION INFORMATION

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.
This symbol indicates that once the appliance is no longer needed, it cannot be disposed together with other miscellaneous municipal waste. Disposal must be carried out in accordance with local environmental regulations for waste disposal. For more detailed information about treatment, recovery and recycling of this product, please contact your local authority, your household waste disposal service or the retailer where you purchased the product. If you decided to scrap the appliance, make it impossible to use in order to prevent possible misadventure. Pull out the electric plug from the electricity supply socket and then cut off the cord. Tear off the gasket. Break the door lock if any.

Do not dismantle the appliance yourself. Pass it on to recycling

companies

Frequently asked questions

The following simple issues can be handled by the user. Please call the after- sale service department if the issues are not settled.

Failed operation

| Check whether the appliance is connected to power or whether the plug is in well contact. Check whether the voltage is too low. Check whether there is a power failure or partial circuits have tripped.
---|---

Odor

| Odorous foods shall be tightly wrapped. Check whether there is any rotten food. Clean the inside of the refrigerator.

Long-time operation of the compressor

| Long operation of the refrigerator is normal in summer when the ambient temperature is high. It is not suggestible having too much food in the appliance at the same time. Food shall get cool before being put into the

appliance. The doors are opened too frequently.

Loud noise

| Check whether the floor is level and whether the refrigerator is placed stably

Check whether accessories are placed at proper locations

Temperature setting impossible

| Check whether the Smart ECO, Fast Freeze, or Vacation function is enabled on the display panel. Exit the special function mode, and then set up the temperature (for details refer to the ELECTRONIC CONTROL PANEL DESCRIPTION section)
Freezer temperature displayed on the panel, with the temperature digits flashing| Press any key to lifting the alarm (for details refer to the ELECTRONIC CONTROL PANEL DESCRIPTION section

Over-temperature alarm function), and then check the foods inside the fridge and freezer compartments get spoiled

Hot housing

| Heat dissipation of the built-in condenser via the housing, which is normal.

When housing becomes hot due to high ambient temperature and storage of too much food,it is recommended to provide sound ventilation to facilitate heat dissipation.

Surface condensation

| Condensation on the exterior surface and door seals of the refrigerator is normal when the ambient humidity is too high. Just wipe the condensate with a clean towel.

Change the Door Stop

•  If necessary, the door can be changed from right•to left-hinged.
• Warning! Before you work on the appliance, always pull the mains plug out of the point.
•  In order to avoid damages to persons and properly execute the change of the door stop with two persons.
•  We recommend leaving the change of the doorstop to experts.
•  Before you start with the modifications, here is some general info:
•  Always pay attention to the number of shims the bearing pins and screws.
•  Position the doors always so that they close tightly.

a) Loosen the screw from the cover of the hinge and remove the cover (pictures similar to product).

b) Unscrew the 4 screws that hold the upper hinge and remove it.

c) Loosen 1 screw as shown in the figure below, order to remove the gap caver on the top side of the appliance.

d) Raise the refrigerator door about 50 mm, in order to remove it from the appliance.

Step 2
a) Loosen the 3 screws that hold the middle hinge and then remove it.

b) Raise the freezer door about 50 mm, so you can remove it from the fridge.

cl Remove the adjustable front stands below the lower hinge. Then, loosen the 4 screws that hold the lower hinge and remove it from the fridge.

The removal of the doors is now finished.

Step3
a) Install the removed parts on the opposite side of the appliance. Pull the door socket, as shown in the following figure, and install it in the respective position on the other side.

b) Remove the screws from the stopper, as shown in the following figure, and install it on the opposite side of the door.

c) Remove the shaft and the two stoppers from the lower hinge and install it in the position, as shown in the following figure.

Step 4
Install the refrigerator and freezer doors on tl1e opposite side.
a) Remove the adjustable stand in the front, as shown below. Then, install the lower hinge on the other side of the fridge and tighten thescrews.

b) Install the shorter adjustable stand in the front on the side, where the lower hinge is. By turning the stand, you can adjust the height on this side of the appliance until it is leveled out.

Step 5
a) Attach the freezer door, turn the middle hinge1so• and then install it on the opposite side of the appliance. Attach the middle hinge with the3 corresponding screws.

b) Attach the refrigerator door and install the upperhinge on the opposite side of the appliance.Attach the upper hinge with the 4 corresponding crews. Attach the upper hinge cover with ascrew.

c) Install the gap cover on the opposite side of the appliance and tighten the screw.

Finally, check for the right alignment of the doors and that they close properly on all sides. If necessary, adjust the stands in the front for a fully horizontal positioning of the appliance

If you have tilted the appliance by more than30°, please wait 4 hours before you connect the appliance to the main supply.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>