Mimiq FN2804172 Finestra Miner User Manual
- June 6, 2024
- Mimiq
Table of Contents
FN2804172 Finestra Miner
User Manual
Introduction
Mimiq, in partnership with Sagem Teknoloji, is introducing the Finestra Miner,
a best-in-class performance, and highly secure gateway with a heartwarming
design that conceals sophisticated engineering. Secure the tamper-resistant
electronics with high-performance placement options.
The Finestra Miner comes with onboard mining, compliant with the current
Helium network specifications, it is ready to install and use with the Helium
App.
Before You Install
Note: Please visit thefinestra.com/ install to get the latest installation instructions. Please refer to the included Quick Start Guide to set your device up faster.
Preparing Your Finestra Miner
- Download the Helium App. Search “Helium Hotspot” in the Apple Store and Google Play.
- IMPORTANT: While signing into the Helium App, please make sure to note down the 12 keywords provided by the Helium App. We would highly recommend that you use the keywords notecard and pen we have sent in the box.
- Open the package and make sure all items are in the box. (See above: What’s in the Box.)
- Screw the provided antenna onto the antenna jack located on the Finestra Miner.
- Do not power your Finestra Miner up before placing it in the preferred location.
- If you choose to connect your Finestra Miner to the internet via the ethernet port you may do so now. For Wi-Fi look at the section “Connecting your Finestra Miner.”
What’s In The Box
1 x Finestra Miner
1 x Power Adaptor
1 x Antenna (915 Mhz)
1 x Power Cable Extender
3 x Wallet Security Keywords Cards
1 x Pen
Dimensions
4.3 x 4.3 x 1.6 in
(110 mm x 110 mm x 40 mm)
Weight
10.5 Oz. (300g)
Supply Voltage
5V / 2A
Device Connectivity
BLE, WiFi, and Ethernet
Working Temperature
-31°F to 167°F
(-35°C to 75°C)
Frequency Support
US915
Antenna Gain
2.6 dBi
Locating Your Finestra Miner
- Preferably place your Finestra Miner near a window with minimal external obstructions.
- If you prefer you can attach your Finestra Miner directly to a sturdy window glass pane with the reusable micro-suction base.
- To activate the micro-suction, examine your Finestra Miner base and carefully remove the protective plastic film on your micro-suction surface with a pair of tweezers.
- To remove and move Finestra Miner just grasp the edges firmly. Pull and twist it to lift the edge from the surface. Lift to remove.
- You can wipe the dust away from the micro-suction to refresh the adhesive property of the surface.
- For a better performance do not place the Finestra Miner near metal meshes, screens or other large metallic objects. Place away from other electronic devices.
Connecting your Finestra Miner
- Power up Finestra Miner using the included power supply.
- WARNING: Please wait for 2 to 3 minutes for your Finestra Miner to boot up before starting the installation process. Do not unplug the Finestra Miner during the set-up process.
- If you choose to connect via Wi-Fi follow the instructions in Helium App as indicated in Step
- Press the “+” button in the Helium App to add your gateway and follow the in-App instructions.
Troubleshooting
- Make sure Bluetooth is on and the phone is connected to the Internet while setting up Finestra Miner.
2. Make sure that the Helium App has Location permissions enabled. These can be found under App Info > Permissions > Location
3. Make sure you have downloaded the latest version of the Helium App from the store.
Limited Warranty
Mimiq provides a limited warranty for Finestra Miner please visit www.thefinestra.com/warranty.
Use and Care
Finestra Miner is not water-resistant. Please use Finestra Miner only indoors and avoid direct contact with water. Finestra Miner works best between -31° F and 167 °F (-35° C and 75° C).
FCC Compliance Statement
Contains FCC ID: 2ABCB-RPI4B
Contains IC: 20953-RPI4B
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
CAUTION: The grantee is not responsible for any changes or modifications
not expressly approved by the party responsible for compliance. Such
modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and all persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canadian Compliance Statement
Contains FCC ID: 2ABCB-RPI4B
Contains IC: 20953-RPI4B
This device contains license-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada license-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
NOTE: This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Product Name: Finestra Miner
Product Model: FN280417-2
Manufacturer:
Mimiq, Inc.
555 Bryant St. #819
Palo Alto, CA 94301
finestrasupport@mimiq.io
www.mimiq.io
Modular Components Used:
NAME: Raspberry Pi4 Model B
MODEL: Raspberry Pi4 Model B
FCC ID: 2ABCB-RPI4B
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Mimiq, Finestra Miner, and the logos are the trademarks of Mimiq, Inc. Helium
and the Helium logo are the trademarks of Helium, Inc. Apple and the Apple
logo are trademarks of Apple Inc.
Google Play and the Google Play logo are trademarks of Google LLC.
© Copyright 2021 Mimiq, Inc. All rights reserved.
Documents / Resources
|
Mimiq FN2804172 Finestra
Miner
[pdf] User Manual
FN2804172, 2A3CX-FN2804172, 2A3CXFN2804172, FN2804172 Finestra Miner, Finestra
Miner, Miner
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>